Michal Chyla
Research Subjects
Research Interests
Michal Chyla has a total of 134 co-authors. Here are the top co-authors by number of shared publications:
- Martin Smrž
HiLASE Centre, FZU - Institute of Physics of the Czech Academy of Sciences, Doln Brezany, Czech Republic
39 shared publications - Tomas Mocek
HiLASE Centre, Institute of Physics of the Czech Academy of Sciences, Za Radnicí 828, 252 41 Dolní Břežany, Czech Republic
31 shared publications Akira Endo
Fyzikalni Ustav AV CR, Vvi, HiLASE Ctr, Za Radnici 828, Dolni Brezany 25241, Czech Republic
23 shared publications- Ondřej Novák
Institute of Physics AS CR
21 shared publications Taisuke Miura
HiLASE Center, Institute of Physics CAS, Za Radnicí 828, Dolní Břežany 25241, Czech Republic
17 shared publications- Jiří Mužík
HiLASE Ctr. (Czech Republic)
10 shared publications
Latest Publications
- Open Access
- 1 January 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (1)
Active alignment control system for thin disk regenerative amplifier
We present an active alignment and stabilization control system for laser setups based on a thin-disk regenerative amplifier. This method eliminates power and pointing instability during the warm-up period and improves long-term stability throughout the entire operation. The alignment method is based on a four-mirror control system consisting of two motorized mirrors placed within the regenerative amplifier cavity, two additional motorized mirrors external to the amplifier cavity, and four camera detectors. The implemented stabilization system achieves significant performance improvements, increasing the power stability from 1.87% to 0.79% RMS and the peak-to-peak stability from 7.43% to 3.88%. Furthermore, the system significantly enhances beam positional stability, achieving up to a sixfold improvement in certain sensor measurements. The advantage of this method is the removal of long-term pointing instability by adding a second controlled motorized mirror to the cavity, in addition to using only one cavity end mirror for optimizing the overlap with the pump spot on the cavity medium. To achieve higher precision in pointing, the nonlinear hysteresis effect of the piezoelectric actuator is mitigated. Although the power and pointing stability of the cavity are secured, pointing instability at the input of the compressor occurs. This issue is resolved by two additional controlled motorized mirrors external to the cavity.
- 1 January 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (1)
Open AccessActive alignment control system for thin disk regenerative amplifier
We present an active alignment and stabilization control system for laser setups based on a thin-disk regenerative amplifier. This method eliminates power and pointing instability during the warm-up period and improves long-term stability throughout the entire operation. The alignment method is based on a four-mirror control system consisting of two motorized mirrors placed within the regenerative amplifier cavity, two additional motorized mirrors external to the amplifier cavity, and four camera detectors. The implemented stabilization system achieves significant performance improvements, increasing the power stability from 1.87% to 0.79% RMS and the peak-to-peak stability from 7.43% to 3.88%. Furthermore, the system significantly enhances beam positional stability, achieving up to a sixfold improvement in certain sensor measurements. The advantage of this method is the removal of long-term pointing instability by adding a second controlled motorized mirror to the cavity, in addition to using only one cavity end mirror for optimizing the overlap with the pump spot on the cavity medium. To achieve higher precision in pointing, the nonlinear hysteresis effect of the piezoelectric actuator is mitigated. Although the power and pointing stability of the cavity are secured, pointing instability at the input of the compressor occurs. This issue is resolved by two additional controlled motorized mirrors external to the cavity.
- 22 February 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (5) , 7708-7715
Investigation of the lasing performance of a crystalline-coated Yb:YAG thin-disk directly bonded onto a silicon carbide heatsink
We investigated the use of crystalline coatings as the highly reflective coating of an Yb:YAG thin disk directly bonded onto a silicon carbide heatsink. Compared to commonly used ion-beam-sputtered coatings, it possesses lower optical losses and higher thermal conductivity, resulting in better heat management and laser outputs. We pumped the disk up to 1.15 kW at 969 nm and reached 665 W of average output power, and disk temperature of 107 °C with a highly multi-modal V-cavity. These promising results were reached with this novel design despite the adoption of a cheap silicon carbide substrate having more than 3 times lower thermal conductivity compared to frequently used CVD diamond.
- 22 February 2022
- Published by Optica Publishing Group in Optics Express
- Vol. 30 (5) , 7708-7715
Investigation of the lasing performance of a crystalline-coated Yb:YAG thin-disk directly bonded onto a silicon carbide heatsink
We investigated the use of crystalline coatings as the highly reflective coating of an Yb:YAG thin disk directly bonded onto a silicon carbide heatsink. Compared to commonly used ion-beam-sputtered coatings, it possesses lower optical losses and higher thermal conductivity, resulting in better heat management and laser outputs. We pumped the disk up to 1.15 kW at 969 nm and reached 665 W of average output power, and disk temperature of 107 °C with a highly multi-modal V-cavity. These promising results were reached with this novel design despite the adoption of a cheap silicon carbide substrate having more than 3 times lower thermal conductivity compared to frequently used CVD diamond.
- 11 March 2020
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 10 (4) , 891-898
Measurement of the piezooptic coefficient of ceramic YAG and analysis of depolarization
To analyze the thermal birefringence effects in laser gain materials, knowledge of the piezooptic coefficients of the materials is required. The piezooptic coefficients of ceramic YAG were measured using the four-point bending method. To our knowledge, this is the first report of this measurement for ceramic YAG. With the measured values, the depolarization of a ceramic YAG laser was analyzed. Overall, the results agree with that of single-crystal YAG in the [111] direction. Ceramic YAG will produce a larger depolarization compared with [100]-direction YAG with an appropriate input polarization angle.
- 11 March 2020
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 10 (4) , 891-898
Measurement of the piezooptic coefficient of ceramic YAG and analysis of depolarization
To analyze the thermal birefringence effects in laser gain materials, knowledge of the piezooptic coefficients of the materials is required. The piezooptic coefficients of ceramic YAG were measured using the four-point bending method. To our knowledge, this is the first report of this measurement for ceramic YAG. With the measured values, the depolarization of a ceramic YAG laser was analyzed. Overall, the results agree with that of single-crystal YAG in the [111] direction. Ceramic YAG will produce a larger depolarization compared with [100]-direction YAG with an appropriate input polarization angle.
- 2 March 2020
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11264, 39
Shaping of picosecond laser pulses by second harmonic generation with time predelay
Shaping and compression of short laser pulses in the course of a second harmonic (2H) generation is a well verified technique in the case of Nd:glass laser radiation converted in KTP crystal cut for type II phase-matching. The laser pulse, few ps in duration, is divided into two orthogonally polarized pulses and one is delayed in respect to the other. Both of them enter the nonlinear optical crystal, in which they propagate with different group velocities. As they are approaching each other, short 2H pulse is generated at their temporal overlap. Shaping of the 2H pulse is achieved by changing the predelay and input pulse intensities. For current high power picosecond laser sources of choice, Yb:YAG lasers, borate crystals have to be used for efficient harmonic generation because of their convenient thermal properties and long lifetime. Although the requirement on group velocities is not fulfilled for the LBO and BBO crystals, numerical calculations have revealed conditions where pulse shaping and even significant pulse compression occur. Fundamental input pulse of 1.8 ps was compressed down to 0.8 ps (FWHM) by 2H generation in LBO crystal. In this work, details about the calculations and measurements of shaping of 2H picosecond Yb:YAG laser pulses in LBO and BBO crystals in dependence on input intensities and predelay will be presented. The shaped 2H pulse measurements performed by an autocorrelator agree well with the calculations, achieving almost 3-fold compression. For the most interesting cases, 2H pulses are characterized by FROG in detail.
- 2 March 2020
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11264, 39
Shaping of picosecond laser pulses by second harmonic generation with time predelay
Shaping and compression of short laser pulses in the course of a second harmonic (2H) generation is a well verified technique in the case of Nd:glass laser radiation converted in KTP crystal cut for type II phase-matching. The laser pulse, few ps in duration, is divided into two orthogonally polarized pulses and one is delayed in respect to the other. Both of them enter the nonlinear optical crystal, in which they propagate with different group velocities. As they are approaching each other, short 2H pulse is generated at their temporal overlap. Shaping of the 2H pulse is achieved by changing the predelay and input pulse intensities. For current high power picosecond laser sources of choice, Yb:YAG lasers, borate crystals have to be used for efficient harmonic generation because of their convenient thermal properties and long lifetime. Although the requirement on group velocities is not fulfilled for the LBO and BBO crystals, numerical calculations have revealed conditions where pulse shaping and even significant pulse compression occur. Fundamental input pulse of 1.8 ps was compressed down to 0.8 ps (FWHM) by 2H generation in LBO crystal. In this work, details about the calculations and measurements of shaping of 2H picosecond Yb:YAG laser pulses in LBO and BBO crystals in dependence on input intensities and predelay will be presented. The shaped 2H pulse measurements performed by an autocorrelator agree well with the calculations, achieving almost 3-fold compression. For the most interesting cases, 2H pulses are characterized by FROG in detail.
- Open Access
- 13 January 2020
- Published by IOP Publishing in Laser Physics
- Vol. 30 (2) , 025405
Balancing the conversion efficiency and beam quality of second harmonic generation of a two-picosecond Yb:YAG thin-disk laser
In this work, the optimization of the second harmonic generation in an LiB3O5 crystal of the 1 kHz, 2 ps Yb:YAG laser is being investigated. Depending on the crystal thickness, an optimal intensity exists, above which the back-conversion process negatively affects the beam quality and pulse shape, while decreasing conversion efficiency. For a selected 2 mm thick frequency doubling crystal, the conversion efficiency of 80% at an optimal intensity of 120 GW cm−2 has been achieved, with output pulse duration of 1.3 ps and with beam quality of 1.4 and 1.6 in a horizontal and vertical direction, respectively, which is only slightly worse than the beam quality at a fundamental frequency.
- 13 January 2020
- Published by IOP Publishing in Laser Physics
- Vol. 30 (2) , 025405
Open AccessBalancing the conversion efficiency and beam quality of second harmonic generation of a two-picosecond Yb:YAG thin-disk laser
In this work, the optimization of the second harmonic generation in an LiB3O5 crystal of the 1 kHz, 2 ps Yb:YAG laser is being investigated. Depending on the crystal thickness, an optimal intensity exists, above which the back-conversion process negatively affects the beam quality and pulse shape, while decreasing conversion efficiency. For a selected 2 mm thick frequency doubling crystal, the conversion efficiency of 80% at an optimal intensity of 120 GW cm−2 has been achieved, with output pulse duration of 1.3 ps and with beam quality of 1.4 and 1.6 in a horizontal and vertical direction, respectively, which is only slightly worse than the beam quality at a fundamental frequency.
- Open Access
- 13 January 2020
- Published by IOP Publishing in Laser Physics
- Vol. 30 (2) , 025005
Investigation of spectrally-dependent phonon relaxation mechanism in Yb:YAG gain media and its consequences for thin disk laser performance
Nonlinear phonon relaxation in Yb:YAG gain media has previously been investigated, and a hypothesis correlating photo-induced free electrons and heat generation in crystals pumped at a wavelength of 940 nm was established (Brandt et al 2011 Appl. Phys. B 102 765–8). Later, we demonstrated efficient suppression of nonlinear phonon relaxation by zero-phonon line (ZPL) pumping of Yb:YAG (969 nm). However, no hypothesis has yet been tested that correlates the heat load and the free electrons in Yb:YAG media. We investigate, both theoretically and experimentally, the behaviour of an Yb:YAG slab pumped by a high-power laser diode at a conventional broadband line (absorption maximum at 941 nm) and a ZPL (absorption maximum at 969 nm), and we compare the generated photocurrent, temperature, and absorbed pump power for those two pump wavelengths. Although the hypothesis established by Brandt et al (2011 Appl. Phys. B 102 765–8) was not confirmed, and the measured photocurrent was identical for the two pump wavelengths, our measurement contributes to the knowledge of the inner processes in Yb:YAG active media. In the following steps we characterized an Yb:YAG thin disk laser, measured the spectrally-resolved absorption and disk surface temperature, and optimised our predictive model of thin disk behaviour. All the experimental and theoretical results are reported.
- 13 January 2020
- Published by IOP Publishing in Laser Physics
- Vol. 30 (2) , 025005
Open AccessInvestigation of spectrally-dependent phonon relaxation mechanism in Yb:YAG gain media and its consequences for thin disk laser performance
Nonlinear phonon relaxation in Yb:YAG gain media has previously been investigated, and a hypothesis correlating photo-induced free electrons and heat generation in crystals pumped at a wavelength of 940 nm was established (Brandt et al 2011 Appl. Phys. B 102 765–8). Later, we demonstrated efficient suppression of nonlinear phonon relaxation by zero-phonon line (ZPL) pumping of Yb:YAG (969 nm). However, no hypothesis has yet been tested that correlates the heat load and the free electrons in Yb:YAG media. We investigate, both theoretically and experimentally, the behaviour of an Yb:YAG slab pumped by a high-power laser diode at a conventional broadband line (absorption maximum at 941 nm) and a ZPL (absorption maximum at 969 nm), and we compare the generated photocurrent, temperature, and absorbed pump power for those two pump wavelengths. Although the hypothesis established by Brandt et al (2011 Appl. Phys. B 102 765–8) was not confirmed, and the measured photocurrent was identical for the two pump wavelengths, our measurement contributes to the knowledge of the inner processes in Yb:YAG active media. In the following steps we characterized an Yb:YAG thin disk laser, measured the spectrally-resolved absorption and disk surface temperature, and optimised our predictive model of thin disk behaviour. All the experimental and theoretical results are reported.
- 11 December 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (05) , 3626-3631
CURRENT ADVANCES IN HIGH AVERAGE POWER DIODE-PUMPED LASERS
In the last two decades, the price of the laser diodes significantly dropped and made them an energy-effective solution for pumping high energy class high average power solid-state lasers. This is a significant advantage for the potential use of such lasers in industry, where operation cost is co...
- 11 December 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (05) , 3626-3631
CURRENT ADVANCES IN HIGH AVERAGE POWER DIODE-PUMPED LASERS
In the last two decades, the price of the laser diodes significantly dropped and made them an energy-effective solution for pumping high energy class high average power solid-state lasers. This is a significant advantage for the potential use of such lasers in industry, where operation cost is co...
- 11 December 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (05) , 3620-3625
COMPACT, PICOSECOND, KW-CLASS THIN-DISK LASER PERLA FOR HI-TECH INDUSTRIAL APPLICATIONS
Ultrashort-pulse, high average power thin-disk lasers matured and became efficient tools for precise material processing and hi-tech laser applications. Hilase centre developed a diode-pumped thin-disk laser platform for Yb:YAG regenerative amplifiers delivering pulse energy >40 mJ, pulse repe...
- 11 December 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (05) , 3620-3625
COMPACT, PICOSECOND, KW-CLASS THIN-DISK LASER PERLA FOR HI-TECH INDUSTRIAL APPLICATIONS
Ultrashort-pulse, high average power thin-disk lasers matured and became efficient tools for precise material processing and hi-tech laser applications. Hilase centre developed a diode-pumped thin-disk laser platform for Yb:YAG regenerative amplifiers delivering pulse energy >40 mJ, pulse repe...
- 11 December 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (05) , 3406-3409
EUV SOURCE AT HiLASE: THE STATE OF THE ART
An overview of the Extreme Ultraviolet (EUV) source to be constructed in the frame of the Czech national R&D project HiLASE (High average power pulsed LASErs) is presented. The HiLASE EUV source will be devoted to industrial and medical applications, as well as to fundamental studies (such as...
- 11 December 2019
- Published by MM Publishing, s.r.o. in MM Science Journal
- Vol. 2019 (05) , 3406-3409
EUV SOURCE AT HiLASE: THE STATE OF THE ART
An overview of the Extreme Ultraviolet (EUV) source to be constructed in the frame of the Czech national R&D project HiLASE (High average power pulsed LASErs) is presented. The HiLASE EUV source will be devoted to industrial and medical applications, as well as to fundamental studies (such as...
- 22 October 2019
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 36 (11) , 3098-3103
Single-shot laser beam parameter measurement system for near-infrared laser beams
We present a simple and fast technique for measuring laser beam parameters, including focus shift using Yaglass, a telecentric lens, and a camera. Our technique is based on imaging of visible fluorescence that represents caustic of the focused near-infrared laser beam. By processing a single camera frame, a large number of second-moment beam diameters are calculated simultaneously without any need for a traditional scan in the propagation direction. The ${{M}^2}$ values measured with this method and standard method are in excellent agreement. We extend this technique to measure the focus shift and focus spot size. This method is fast and allows the real-time monitoring of laser beam parameters simultaneously during the manufacturing process.- 22 October 2019
- Published by Optica Publishing Group in Journal of the Optical Society of America B
- Vol. 36 (11) , 3098-3103
Single-shot laser beam parameter measurement system for near-infrared laser beams
We present a simple and fast technique for measuring laser beam parameters, including focus shift using Yaglass, a telecentric lens, and a camera. Our technique is based on imaging of visible fluorescence that represents caustic of the focused near-infrared laser beam. By processing a single camera frame, a large number of second-moment beam diameters are calculated simultaneously without any need for a traditional scan in the propagation direction. The ${{M}^2}$ values measured with this method and standard method are in excellent agreement. We extend this technique to measure the focus shift and focus spot size. This method is fast and allows the real-time monitoring of laser beam parameters simultaneously during the manufacturing process.