AVAlesya Valer'Yevna Vurasko

Alesya Valer'Yevna Vurasko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Alesya Valer'Yevna Vurasko has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization of Sorption Materials Based on Cellulose from Non-Wood Plant Raw Materials

    by Anatoly P. Karmanov, Ludmila S. Kocheva, Alesia V. Vurasko, Natalia G. Rachkova, Valerii A. Demin

    This paper examines the issues related to the use of various types of non-wood plant raw materials for the development of new cellulose-based sorbents. The work aims to collect new data on the structural features and sorption properties of non-wood celluloses towards the heavy natural radionuclide uranium-238. Cellulose samples were isolated from the rye straw (Secale), wheat (Triticum), and oats (Avena sativa), as well as from the hogweed stems (Heracleum sosnowskyi) and the brown seaweed (Laminaria digitata). A study of plant raw materials has shown that, in terms of cellulose content, grasses are almost comparable to woody plants, and the cellulose content in their xylem ranges from 45 to 49 %. Fourier transform infrared spectroscopy revealed that all herbaceous plant celluloses have a virtually identical chemical structure. The surface-pore structure of cellulose was studied by means of low-temperature nitrogen adsorption. Analysis of nitrogen adsorption behavior has shown that all the studied samples should be classified as mesoporous materials with a low specific surface area. We have determined the general patterns governing the adsorption of uranium-238 from aqueous solutions with low concentrations of uranium-238 (0.750 μg/mL). The studied cellulose samples are characterized by strong retention of uranium-238, a significant portion of which (up to 90 %) is not desorbed by water or by aqueous solutions of CH3COONH4 and HCl (1 M). A correlation has been found between the parameters of the surface-porous structure and the adsorption-desorption parameters. Cellulose derived from hogweed, which has the highest specific surface area, can be recommended for the removal of trace amounts of the radionuclide uranium-238 from aqueous media. The results confirm the high innovative potential of cellulose derived from non-wood plants.

  • Open Access

    SORPTION PROPERTIES OF SILICА-CONTAINING CELLULOSE FROM RICE HUSK

    by Alesja Valer'EVna Vurasko, Inna Gennadyevna Pervova, Irina Olegovna Shapovalova, Yakov Vladimirovich Kazakov, Ekaterina Yuryevna Patrakova

    Cellulose-based sorbents from renewable sources, more specifically, plant cell membranes, are getting increasingly used as solid-phase matrix carriers in hybrid reagent indicator test systems, since the sorbents can provide high sensitivity to the toxicants to be detected/determined due to combining two operations - concentration and registration of the analytical signal, directly in the sorbent phase. The study was aimed to reveal relationships between the properties of preserved natural silicon dioxide during oxidative-organosolv delignification of rice husk and on the sorption properties. In this work, it was produced paper samples of silicon-based materials from silica-containing rice husk ash residue from 0.3 to 32.5% by weight of the absolutely dry raw materials, as well as it was found that the higher the content of mineral component, the higher specific surface area and pore volume. It was revealed that while forming a paper sheet, «concentrating» of mineral components occurs on the mesh side, which results in decreasing the crystallinity index and doubling the SiO2 content. It has been shown that it is the mineral part that appears to be quite stably colored after the silicon-containing cellulose matrices have been impregnated with the reagent 1-(4-aminosulfonylphenyl)-3-phenyl-5-(benzylbenzimidazolyl-2) formazan. Retention of organic reagents in the silica phase does not interfere with the chromogenic complexation reaction when the reagents interact with aqueous solutions of Cu (II) and Zn(II) salts. The contrasting color transition observed can be used for design of solid-phase reagent indicator test systems to detect copper (II) and zinc (II) ions in aqueous media.

  • Deriving Biocomposites of Polymer Phase Plasticised Cellulose Acetates with Varying Degrees of Acetylation

    by Urals State Forest Engineering University, Aleksey E. Shkuro, Victor V. Glukhikh, Kristina A. Usova, Denis D. Chirkov, Pavel S. Zakharov, Alesya V. Vurasko

    It is anticipated that the creation of wood-polymer composites (WPC) made of naturally renewable polymers and their derivatives (biocomposites) would have a significant practical use due to the rise in prices for synthetic thermoplastic polymers derived from oil and gas. Furthermore, the necessity to replace synthetic polymers such as polyethylene, polypropylene, polyvinyl chloride, and others as components of composite materials is also associated with environmental hazards caused by their low degradation rate in the natural media (soil, water, and air). A further problem for manufacturers of WPC is the legislative requirement for autonomous neutralisation of production waste. One of the potential materials for practical application in the production of WPC are binders based on plasticised cellulose acetates. Russian and foreign scientists have studied the influence of the degree of acetylation of cellulose acetate on the properties of polymeric materials that do not contain lignocellulose fillers. There is no information found concerning the secondary use of cellulose acetate waste for the production of WPC. This article presents the results of an investigation into the hot pressing of biocomposites with a polymer phase of plasticised cellulose acetates of varying degrees of acetylation and fillers: wood flour and waste acetate photographic film. An experimental and statistical dependence of the effect of the degree of acetylation of cellulose acetate and filler content in the biocomposite on its properties was developed, sufficient to exceed a confidence level of 0.9. The experimental specifications included decomposition in activated soil, water absorption, bending strength, Brinell hardness, etc. Some test results showed that the derived biocomposites have the same level of properties as the reference WPC, which consists of a high-density polyethylene phase with a wood flour content of 50 %. The derived dependencies allow us to predict changes in the properties of biocomposites at different degrees of acetylation of plasticised cellulose acetate and filler content. Moreover, they solve the problem of choosing the optimal chemical combination for WPC for manufacturing a specific product by hot pressing. For citation: Shkuro A.E., Glukhikh V.V., Usova K.A., Chirkov D.D., Zakharov P.S., Vurasko A.V. Deriving Biocomposites of Polymer Phase Plasticised Cellulose Acetates with Varying Degrees of Acetylation. Lesnoy Zhurnal = Russian Forestry Journal, 2023, no. 4, pp. 155–168. (In Russ.). https://doi.org/10.37482/0536-1036-2023-4-155-168


  • Reduction of Paper Pulp Fluctuations in Tissue Paper Making Machine

    by Ural State Forestry Engineering University, Valeriy P. Sivakov, Alesia V. Vurasko, Alexey L. Sherstobitov

    The subject of the research is a paper for sanitary-hygienic purposes. The objects of the study are a pulper infeed system and a round grid perforated forming device. The purposes of the work are to identify sources and reduce fluctuations of 1 m2 of pulp for sanitaryhygienic paper, which decrease the structural irregularities of the paper web in longitudinal and transverse directions. The methodology of the study is to investigate the flow pulsation of the pulp, the fluctuations of the pulp web at the Yankee cylinder (without crepe), to verify the tensile strength of the paper web in longitudinal and transverse directions for identification of a correlation between the pulsation, the vibration of the pulp and the strength of the paper web. The trials were made during the production of sanitary-hygienic paper with the mass 17–18 g/m2 at a steady working speed of the machine 5 m/s. Pulsations of paper pulp in the low-frequency spectrum of 0.14–1.35 Hz prevail in the mass-intake device. The rectangular paper samples 432×230 mm2 were created for examination of structural irregularities of the paper web. The length 432 mm was taken in the longitudinal direction of paper movement in the machine. It was equal to 0.125 mm in the circumference of the round grid screen cylinder. The width of the paper web in the commodity bobbin was 230 mm. The samples were made from a single sheet of paper sequentially without intermediate cuts at 5 m/s speed of the machine. It was determined that the frequencies of fluctuations of the masses of sanitary paper samples coincide by 86 % with the pulsation frequencies of the pulp and depend on other factors by 14 %. The major frequency was 1.45 Hz. The amplitude of the deviation of the mass at this frequency from the arithmetic mean was 0.026 g. The tensile strength of the paper web in the machine direction was 5.6 times greater than in the transverse direction. It was caused by unregulated rotation frequency of the holey roll and clogging of its holes. The significant change of speed of the pulp flow on the short cylindrical part of the vacuum chambers initiated synchronically low frequency pulsation of the pulp and fluctuations of masses of the paper samples, therefor, the paper web in the machine. The irregularities of the structure of the paper web create the frequent paper breaks and reduced quality of the commodity products.

  • Open Access

    PREPARATION AND PROPERTIES OF TECHNICAL CELLULOSE FROM HOGWEED BY THE OXIDATIVE-ORGANOSOLVENT METHOD

    by Alesja Valer'EVna Vurasko, Maksim Arkad'YEvich Ageev, Valeriy Pavlovich Sivakov

    Hogweed multiplies rapidly and gains a large volume of phytomass during the growing season, which allows us to consider the mature biomass of hogweed as a raw material for cellulose production. The aim of the work is to obtain cellulose from lignified stems of hogweed by an oxidative-organosolvent method and study its properties. Raw materials in the form of stems harvested in August contain less lignin, more cellulose and minerals, compared to raw materials harvested in September. The component composition of raw materials: the mass fraction of lignin is 21.9%, cellulose is 46.4% of the absolutely dry raw materials. Depending on the conditions, cellulose with a yield of 49.5–49.7% was obtained by redox-organosolvent cooking with preliminary alkaline treatment % of absolutely dry raw materials, the mass fraction of lignin is 3.9–4.3% of the mass of absolutely dry cellulose, whiteness 72.0–80.2%. The best indicators for physical and mechanical properties are cellulose obtained at a consumption of 0.8 g/g of equilibrium peroxyacetic acid and with a duration of alkaline treatment of 90 minutes. The analysis of cellulose showed that it is possible to obtain cellulose from hogweed that is comparable in characteristics to GOST 28172-89. The anatomical elements of cellulose contain bast fibers, parenchymal cells and vessels. The average fiber length is 0.70 mm, and the average fiber width is 20.4 microns. According to the fractional composition and fiber sizes, the resulting cellulose should be attributed to short-fiber semi-finished products.


  • Calculation of impregnating column for seismic stability

    by Ural State Forestry Engineering University, Valeriy Sivakov, Alesia Vurasko, Ruslan Garifyanov

    ????? ??????????, ?????????? ??????????????, ?????????? ??????????, ??????? ???????, ?????? ?? ????????, ?????????? ????????, ???????? ??????????, ??????????? ???????, ????? ? ??????????, ?????????? ??????????, ??????? ??????????

  • Open Access

    IMPROVING THE TECHNOLOGY OF PRODUCING CELLULOSE OXIDATION-ORGANOSOLVENT WAY OF NON-WOOD PLANT MATERIALS

    by Alesya Valer'Yevna Vurasko, Elena Igorevna Simonova, Anastasiya Rashitovna Minakova, Valeriy Pavlovich Sivakov

    Разработана усовершенствованная принципиальная технологическая схема получения целлюлозы окислительно-органосольвентным способом из недревесного растительного сырья с предварительной щелочной обработкой и рекуперацией отработанного варочного раствора. Показана возможность получения технической целлюлозы с заданными свойствами при многократном использовании отработанного варочного раствора, что позволяет сократить расход уксусной кислоты и свежей воды в два и 1.7 раза соответственно. Схема включает следующие стадии: подготовку сырья; приготовление варочной композиции и щелочного раствора, щелочную обработку, варку и промывку целлюлозы, рекуперацию отработанного варочного раствора, нейтрализацию отработанного щелочного раствора и использование загрязненной воды. При реализации предложенной технологической схемы образуются следующие виды загрязненной воды: вода для промывки растительного сырья циркулирует по первой и второй ступеням при добавлении воды с нейтрализатора; оборотная вода от промывки технической целлюлозы в три ступени – промывную воду с первой ступени промывки направляют в нейтрализатор; промывную воду со второй ступени промывки направляют на первую ступень промывки технической целлюлозы; на третью ступень промывки подают воду с барабанного фильтра с добавлением свежей воды; концентрация гидроксида натрия в отработанном щелочном растворе составляет 1.75%. В нейтрализаторе образуется вода с концентрацией уксусной кислоты 0.83 % и ацетата натрия с концентрацией 2.5%; воду с нейтрализатора подают на первую ступень промывки растительного сырья. Свежая вода используется для приготовления равновесной перуксусной кислоты, щелочного раствора и на третью ступень промывки технической целлюлозы. Твердые отходы образуются в гидроразбивателе при промывке растительного сырья; в баке отработанного варочного раствора в виде осадка из нулевого волокна; в нейтрализаторе промытый осадок можно использовать как противоморозную добавку для бетонов. В качестве основного технологического оборудования предложено использовать реактор и нейтрализатор.


  • Open Access

    RECOVERY OF PERFORMED COOKING SOLUTIONS AT OXIDATIVE-ORGAN-SOLVENT WARNES IN NEEDRE PLANT RAW MATERIALS

    by Alesya Valer'Yevna Vurasko, Anastasiya Rashitovna Minakova, Elena Igorevna Simonova

    The possibility of recovering the spent cooking solution with the replacement of the missing amount of lignifying reagents in the oxidative-organic solvent cooking of non-woody plant raw materials (rice husk) with preliminary alkaline treatment and the production of technical pulp with desired properties is shown. Analysis of scientific and patent information revealed that two methods of regeneration are used for regeneration of spent cooking solutions during oxidation-organosolve cooking: azeotropic distillation and return of part of the spent cooking solution for re-cooking with the completion of the missing amount of reagents. For the oxidation-organosolvent cooking non-wood plant materials the most promising is the second option. To avoid the preservation of mineral components in industrial pulp, non-wood plant materials are subjected to alkaline treatment. It has been established that to obtain technical pulp with recovery of the spent cooking solution, it is required two times less acetic acid and 1.7 times fresh water as compared to oxidation-organic solvent cooking under standard conditions with a constant amount of caustic soda.


  • Hybrid composites based on technical cellulose from rice husk

    by Irina Shapovalova, Alesya Vurasko, Lev Petrov, Eduard Kraus, Heinrich Leicht, Michael Heilig, Oleg Stoyanov

    We introduced the preparation of hybrid composites using technical cellulose as a matrix material from rice husks with a natural SiO2 content from 0% to 19.4%. In this work, the physicochemical characteristics of the resulting hybrid composites have been investigated. The presence of SiOC chemical bonds in the resulting hybrid composites was determined by infrared spectroscopy. Microscopic analysis showed the complete removal of the mineral component and lignin from the cell wall of the rice husk fibers. This allows obtaining of an expanded surface of the fibers (101.7 m2/g) with uniform distribution of the TiO2 aggregates. It could be shown that with content increasing of natural silicon dioxide in the hybrid composite the decomposition rate of H2O2 also increases. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45796.