Christof Weis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Christof Weis has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Peter Habisreuther
Karlsruhe Institute of Technology, Engler‐Bunte‐Institute, Division of Combustion Technology, Engler‐Bunte‐Ring 1, 76131 Karlsruhe, Germany
3 shared publications - Dimosthenis Trimis
Engler-Bunte-Institute: Combustion Technology, Karlsruhe Institute of Technology 3 , 76131 Karlsruhe, Germany
2 shared publications Nikolaos Zarzalis
Karlsruhe Institute of Technology, Karlsruhe, Germany
2 shared publicationsPeter Habisreuther
Karlsruhe Institute of Technology, Karlsruhe, Germany
2 shared publicationsAlexander Schwagerus
Karlsruhe Institute of Technology, Karlsruhe, Germany
1 shared publicationBerthold Koestlin
Siemens AG, Mülheim an der Ruhr, Germany
1 shared publication
Latest Publications
- Open Access
- 5 October 2025
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 41
Experimental investigation of turbulent premixed H2-jet flames at high exhaust gas recirculation
- 5 October 2025
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 41
Open AccessExperimental investigation of turbulent premixed H2-jet flames at high exhaust gas recirculation
- Open Access
- 23 September 2022
- Published by Elsevier in Combustion and Flame
- Vol. 245
3D direct pore level simulations of radiant porous burners
- 23 September 2022
- Published by Elsevier in Combustion and Flame
- Vol. 245
Open Access3D direct pore level simulations of radiant porous burners
- 5 July 2019
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 191 (9) , 1693-1710
Change in Flame Geometry of an Ethanol Spray Flame by Varying the Spray Characteristics
Turbulent swirl flames using fuel sprays are found in many combustion systems. Since sprays with different characteristics can be produced, pulsed spray injection allows the realization of different flame types using the same burner. Two different flame types have been studied experimentally and numerically: a burner-attached and a lifted flame. Large eddy simulations using Lagrangian particles to represent the spray, and a combined presumed PDF and tabulated chemistry approach to model the turbulent combustion are able to represent the different flame types. A simple-to-implement improvement of the numerical algorithm for the droplets is proposed, consisting of the redistribution of the droplet source terms between all neighbor cells of the gas phase. This improvement stabilizes the numerical method and allows the use of large time steps. The numerical results have been used to investigate the phenomena leading to the different flame geometries. They show that the burner-attached flame is caused by a destructive interaction between the spray droplets and the central recirculation zone (CRZ). In the case of the lifted flame, the CRZ is preserved.
- 5 July 2019
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 191 (9) , 1693-1710
Change in Flame Geometry of an Ethanol Spray Flame by Varying the Spray Characteristics
Turbulent swirl flames using fuel sprays are found in many combustion systems. Since sprays with different characteristics can be produced, pulsed spray injection allows the realization of different flame types using the same burner. Two different flame types have been studied experimentally and numerically: a burner-attached and a lifted flame. Large eddy simulations using Lagrangian particles to represent the spray, and a combined presumed PDF and tabulated chemistry approach to model the turbulent combustion are able to represent the different flame types. A simple-to-implement improvement of the numerical algorithm for the droplets is proposed, consisting of the redistribution of the droplet source terms between all neighbor cells of the gas phase. This improvement stabilizes the numerical method and allows the use of large time steps. The numerical results have been used to investigate the phenomena leading to the different flame geometries. They show that the burner-attached flame is caused by a destructive interaction between the spray droplets and the central recirculation zone (CRZ). In the case of the lifted flame, the CRZ is preserved.
- 17 June 2019
- Published by ASME International
Combustion Characteristics of Natural Gas Fueled, Premixed Turbulent Jet Flame Arrays Confined in a Hexagonal Combustor
In order to extend the operation regime of existing gas turbine combustion systems to lower the minimum loads, the applicability of matrix burners (arrays of jet flames) as an alternative to conventional swirl stabilized burners has been considered. In comparison to well-studied single jet flame systems, the effects of geometry and thermodynamic parameters on characteristics of matrix burner systems have not been studied in detail. Information, which is essential for design processes e.g. scaling of matrix burners, is not yet available in public domain. This work involves a systematic investigation of a matrix burner system operating at highly turbulent flow conditions (Reynolds Number ≈ 20000) prevailing in gas turbine combustion systems. In order to understand the effects of geometrical scaling, three variants of jet diameter have been investigated. A detailed test campaign including lean blow out limits detection, velocity field measurement and hydroxyl radical (OH*) chemiluminescence recording has been conducted. Influence of variation in stoichiometry and exit velocity of fuel-air mixture has been captured. The results show that it is possible to generalize the scaling of the matrix burner using the well-known Peclet criterion.
- 17 June 2019
- Published by ASME International
Combustion Characteristics of Natural Gas Fueled, Premixed Turbulent Jet Flame Arrays Confined in a Hexagonal Combustor
In order to extend the operation regime of existing gas turbine combustion systems to lower the minimum loads, the applicability of matrix burners (arrays of jet flames) as an alternative to conventional swirl stabilized burners has been considered. In comparison to well-studied single jet flame systems, the effects of geometry and thermodynamic parameters on characteristics of matrix burner systems have not been studied in detail. Information, which is essential for design processes e.g. scaling of matrix burners, is not yet available in public domain. This work involves a systematic investigation of a matrix burner system operating at highly turbulent flow conditions (Reynolds Number ≈ 20000) prevailing in gas turbine combustion systems. In order to understand the effects of geometrical scaling, three variants of jet diameter have been investigated. A detailed test campaign including lean blow out limits detection, velocity field measurement and hydroxyl radical (OH*) chemiluminescence recording has been conducted. Influence of variation in stoichiometry and exit velocity of fuel-air mixture has been captured. The results show that it is possible to generalize the scaling of the matrix burner using the well-known Peclet criterion.