Yingzhi Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yingzhi Sun has a total of 98 co-authors. Here are the top co-authors by number of shared publications:
- Gerbrand Ceder
Department of Materials Science and Engineering University of California Berkeley California USA
10 shared publications - Zijian Cai
Lawrence Berkeley National Laboratory Materials Sciences Division Berkeley CA 94720 USA
6 shared publications - Zhengyan Lun
School of Chemical Sciences, University of Chinese Academy of Sciences, Beijing, China
4 shared publications - Bin Ouyang
Florida State University
3 shared publications - Chongmin Wang
Environmental Molecular Sciences Laboratory Pacific Northwest National Laboratory Richland Washington USA
3 shared publications - Haegyeom Kim
Lawrence Berkeley National Laboratory
3 shared publications
Latest Publications
- Open Access
- 19 September 2024
- Published by Springer Nature in Nature Nanotechnology
- Vol. 19 (12) , 1831-1839
Earth-abundant Li-ion cathode materials with nanoengineered microstructures
Manganese-based materials have tremendous potential to become the next-generation lithium-ion cathode as they are Earth abundant, low cost and stable. Here we show how the mobility of manganese cations can be used to obtain a unique nanosized microstructure in large-particle-sized cathode materials with enhanced electrochemical properties. By combining atomic-resolution scanning transmission electron microscopy, four-dimensional scanning electron nanodiffraction and in situ X-ray diffraction, we show that when a partially delithiated, high-manganese-content, disordered rocksalt cathode is slightly heated, it forms a nanomosaic of partially ordered spinel domains of 3–7 nm in size, which impinge on each other at antiphase boundaries. The short coherence length of these domains removes the detrimental two-phase lithiation reaction present near 3 V in a regular spinel and turns it into a solid solution. This nanodomain structure enables good rate performance and delivers 200 mAh g−1 discharge capacity in a (partially) disordered material with an average primary particle size of ∼5 µm. The work not only expands the synthesis strategies available for developing high-performance Earth-abundant manganese-based cathodes but also offers structural insights into the ability to nanoengineer spinel-like phases.
- 19 September 2024
- Published by Springer Nature in Nature Nanotechnology
- Vol. 19 (12) , 1831-1839
Open AccessEarth-abundant Li-ion cathode materials with nanoengineered microstructures
Manganese-based materials have tremendous potential to become the next-generation lithium-ion cathode as they are Earth abundant, low cost and stable. Here we show how the mobility of manganese cations can be used to obtain a unique nanosized microstructure in large-particle-sized cathode materials with enhanced electrochemical properties. By combining atomic-resolution scanning transmission electron microscopy, four-dimensional scanning electron nanodiffraction and in situ X-ray diffraction, we show that when a partially delithiated, high-manganese-content, disordered rocksalt cathode is slightly heated, it forms a nanomosaic of partially ordered spinel domains of 3–7 nm in size, which impinge on each other at antiphase boundaries. The short coherence length of these domains removes the detrimental two-phase lithiation reaction present near 3 V in a regular spinel and turns it into a solid solution. This nanodomain structure enables good rate performance and delivers 200 mAh g−1 discharge capacity in a (partially) disordered material with an average primary particle size of ∼5 µm. The work not only expands the synthesis strategies available for developing high-performance Earth-abundant manganese-based cathodes but also offers structural insights into the ability to nanoengineer spinel-like phases.
- Open Access
- 5 July 2024
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 10 (27) , eadp3309
Quantifying the regime of thermodynamic control for solid-state reactions during ternary metal oxide synthesis
The success of solid-state synthesis often hinges on the first intermediate phase that forms, which determines the remaining driving force to produce the desired target material. Recent work suggests that when reaction energies are large, thermodynamics primarily dictates the initial product formed, regardless of reactant stoichiometry. Here, we validate this principle and quantify its constraints by performing in situ characterization on 37 pairs of reactants. These experiments reveal a threshold for thermodynamic control in solid-state reactions, whereby initial product formation can be predicted when its driving force exceeds that of all other competing phases by ≥60 milli–electron volt per atom. In contrast, when multiple phases have a comparable driving force to form, the initial product is more often determined by kinetic factors. Analysis of the Materials Project data shows that 15% of possible reactions fall within the regime of thermodynamic control, highlighting the opportunity to predict synthesis pathways from first principles.
- 5 July 2024
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 10 (27) , eadp3309
Open AccessQuantifying the regime of thermodynamic control for solid-state reactions during ternary metal oxide synthesis
The success of solid-state synthesis often hinges on the first intermediate phase that forms, which determines the remaining driving force to produce the desired target material. Recent work suggests that when reaction energies are large, thermodynamics primarily dictates the initial product formed, regardless of reactant stoichiometry. Here, we validate this principle and quantify its constraints by performing in situ characterization on 37 pairs of reactants. These experiments reveal a threshold for thermodynamic control in solid-state reactions, whereby initial product formation can be predicted when its driving force exceeds that of all other competing phases by ≥60 milli–electron volt per atom. In contrast, when multiple phases have a comparable driving force to form, the initial product is more often determined by kinetic factors. Analysis of the Materials Project data shows that 15% of possible reactions fall within the regime of thermodynamic control, highlighting the opportunity to predict synthesis pathways from first principles.
- Open Access
- 27 March 2024
- Published by Springer Nature in Nature Materials
- Vol. 23 (5) , 724
Publisher Correction: Unlocking Li superionic conductivity in face-centred cubic oxides via face-sharing configurations
- 27 March 2024
- Published by Springer Nature in Nature Materials
- Vol. 23 (5) , 724
Open AccessPublisher Correction: Unlocking Li superionic conductivity in face-centred cubic oxides via face-sharing configurations
- Open Access
- 2 February 2024
- Published by Springer Nature in Nature Materials
- Vol. 23 (4) , 535-542
Unlocking Li superionic conductivity in face-centred cubic oxides via face-sharing configurations
Oxides with a face-centred cubic (fcc) anion sublattice are generally not considered as solid-state electrolytes as the structural framework is thought to be unfavourable for lithium (Li) superionic conduction. Here we demonstrate Li superionic conductivity in fcc-type oxides in which face-sharing Li configurations have been created through cation over-stoichiometry in rocksalt-type lattices via excess Li. We find that the face-sharing Li configurations create a novel spinel with unconventional stoichiometry and raise the energy of Li, thereby promoting fast Li-ion conduction. The over-stoichiometric Li–In–Sn–O compound exhibits a total Li superionic conductivity of 3.38 × 10−4 S cm−1 at room temperature with a low migration barrier of 255 meV. Our work unlocks the potential of designing Li superionic conductors in a prototypical structural framework with vast chemical flexibility, providing fertile ground for discovering new solid-state electrolytes.
- 2 February 2024
- Published by Springer Nature in Nature Materials
- Vol. 23 (4) , 535-542
Open AccessUnlocking Li superionic conductivity in face-centred cubic oxides via face-sharing configurations
Oxides with a face-centred cubic (fcc) anion sublattice are generally not considered as solid-state electrolytes as the structural framework is thought to be unfavourable for lithium (Li) superionic conduction. Here we demonstrate Li superionic conductivity in fcc-type oxides in which face-sharing Li configurations have been created through cation over-stoichiometry in rocksalt-type lattices via excess Li. We find that the face-sharing Li configurations create a novel spinel with unconventional stoichiometry and raise the energy of Li, thereby promoting fast Li-ion conduction. The over-stoichiometric Li–In–Sn–O compound exhibits a total Li superionic conductivity of 3.38 × 10−4 S cm−1 at room temperature with a low migration barrier of 255 meV. Our work unlocks the potential of designing Li superionic conductors in a prototypical structural framework with vast chemical flexibility, providing fertile ground for discovering new solid-state electrolytes.
- Open Access
- 30 January 2024
- Published by Springer Nature in Nature Synthesis
- Vol. 3 (4) , 527-536
Optimal thermodynamic conditions to minimize kinetic by-products in aqueous materials synthesis
Phase diagrams offer substantial predictive power for materials synthesis by identifying the stability regions of target phases. However, thermodynamic phase diagrams do not offer explicit information regarding the kinetic competitiveness of undesired by-product phases. Here we propose a quantitative and computable thermodynamic metric to identify synthesis conditions under which the propensity to form kinetically competing by-products is minimized. We hypothesize that thermodynamic competition is minimized when the difference in free energy between a target phase and the minimal energy of all other competing phases is maximized. We validate this hypothesis for aqueous materials synthesis through two empirical approaches: first, by analysing 331 aqueous synthesis recipes text-mined from the literature; and second, by systematic experimental synthesis of LiIn(IO3)4 and LiFePO4 across a wide range of aqueous electrochemical conditions. Our results show that even for synthesis conditions that are within the stability region of a thermodynamic Pourbaix diagram, phase-pure synthesis occurs only when thermodynamic competition with undesired phases is minimized.
- 30 January 2024
- Published by Springer Nature in Nature Synthesis
- Vol. 3 (4) , 527-536
Open AccessOptimal thermodynamic conditions to minimize kinetic by-products in aqueous materials synthesis
Phase diagrams offer substantial predictive power for materials synthesis by identifying the stability regions of target phases. However, thermodynamic phase diagrams do not offer explicit information regarding the kinetic competitiveness of undesired by-product phases. Here we propose a quantitative and computable thermodynamic metric to identify synthesis conditions under which the propensity to form kinetically competing by-products is minimized. We hypothesize that thermodynamic competition is minimized when the difference in free energy between a target phase and the minimal energy of all other competing phases is maximized. We validate this hypothesis for aqueous materials synthesis through two empirical approaches: first, by analysing 331 aqueous synthesis recipes text-mined from the literature; and second, by systematic experimental synthesis of LiIn(IO3)4 and LiFePO4 across a wide range of aqueous electrochemical conditions. Our results show that even for synthesis conditions that are within the stability region of a thermodynamic Pourbaix diagram, phase-pure synthesis occurs only when thermodynamic competition with undesired phases is minimized.
- Open Access
- 5 October 2023
- Published by Springer Nature in Nature Energy
- Vol. 9 (1) , 27-36
In situ formed partially disordered phases as earth-abundant Mn-rich cathode materials
Earth-abundant cathode materials are urgently needed to enable scaling of the Li-ion industry to multiply terawatt hours of annual production, necessitating reconsideration of how good cathode materials can be obtained. Irreversible transition metal migration and phase transformations in Li-ion cathodes are typically believed to be detrimental because they may trigger voltage hysteresis, poor kinetics and capacity degradation. Here we challenge this conventional consensus by reporting an unusual phase transformation from disordered Li- and Mn-rich rock salts to a new phase (named δ), which displays partial spinel-like ordering with short coherence length and exhibits high energy density and rate capability. Unlike other Mn-based cathodes, the δ phase exhibits almost no voltage fade upon cycling. We identify the driving force and kinetics of this in situ cathode formation and establish design guidelines for Li- and Mn-rich compositions that combine high energy density, high rate capability and good cyclability, thereby enabling Mn-based energy storage.
- 5 October 2023
- Published by Springer Nature in Nature Energy
- Vol. 9 (1) , 27-36
Open AccessIn situ formed partially disordered phases as earth-abundant Mn-rich cathode materials
Earth-abundant cathode materials are urgently needed to enable scaling of the Li-ion industry to multiply terawatt hours of annual production, necessitating reconsideration of how good cathode materials can be obtained. Irreversible transition metal migration and phase transformations in Li-ion cathodes are typically believed to be detrimental because they may trigger voltage hysteresis, poor kinetics and capacity degradation. Here we challenge this conventional consensus by reporting an unusual phase transformation from disordered Li- and Mn-rich rock salts to a new phase (named δ), which displays partial spinel-like ordering with short coherence length and exhibits high energy density and rate capability. Unlike other Mn-based cathodes, the δ phase exhibits almost no voltage fade upon cycling. We identify the driving force and kinetics of this in situ cathode formation and establish design guidelines for Li- and Mn-rich compositions that combine high energy density, high rate capability and good cyclability, thereby enabling Mn-based energy storage.
- Open Access
- 28 April 2023
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 9 (17)
Unraveling Li growth kinetics in solid electrolytes due to electron beam charging
Revealing the local structure of solid electrolytes (SEs) with electron microscopy is critical for the fundamental understanding of the performance of solid-state batteries (SSBs). However, the intrinsic structural information in the SSB can be misleading if the sample’s interactions with the electron beams are not fully understood. In this work, we systematically investigate the effect of electron beams on Al-doped lithium lanthanum zirconium oxide (LLZO) under different imaging conditions. Li metal is observed to grow directly on the clean surface of LLZO. The Li metal growth kinetics and the morphology obtained are found to be heavily influenced by the temperature, accelerating voltage, and electron beam intensity. We prove that the lithium growth is due to the LLZO delithiation activated by a positive charging effect under electron beam emission. Our results deepen the understanding of the electron beam impact on SEs and provide guidance for battery material characterization using electron microscopy.
- 28 April 2023
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 9 (17)
Open AccessUnraveling Li growth kinetics in solid electrolytes due to electron beam charging
Revealing the local structure of solid electrolytes (SEs) with electron microscopy is critical for the fundamental understanding of the performance of solid-state batteries (SSBs). However, the intrinsic structural information in the SSB can be misleading if the sample’s interactions with the electron beams are not fully understood. In this work, we systematically investigate the effect of electron beams on Al-doped lithium lanthanum zirconium oxide (LLZO) under different imaging conditions. Li metal is observed to grow directly on the clean surface of LLZO. The Li metal growth kinetics and the morphology obtained are found to be heavily influenced by the temperature, accelerating voltage, and electron beam intensity. We prove that the lithium growth is due to the LLZO delithiation activated by a positive charging effect under electron beam emission. Our results deepen the understanding of the electron beam impact on SEs and provide guidance for battery material characterization using electron microscopy.
- 11 October 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (43) , 23155-23164
Electronic structure manipulation via composition tuning for the development of highly conductive and acid-stable oxides
Exploring materials that simultaneously possess high conductivity and electrochemical stability is critical for various energy-conversion applications. In this study, our combined computations and experiments suggest the Mg–Ti–O chemical space for novel ternary oxide compounds offering high electrical conductivity and corrosion stability in acidic conditions to be potentially used as catalyst supporter of polymer electrolyte membrane fuel cells. High electrical conductivity (6.09 × 10−1 S cm−1) is achieved at room temperature by tuning the chemical composition of Mg1−xTi2+xO5 while still maintaining good corrosion stability (1.2 × 10−4 mA cm−2 after six days) in acidic conditions. Furthermore, we discover that a reducing gas environment during the synthesis increases the Ti solubility in Mg1−xTi2+xO5 with a reduced valence state of Ti, thus resulting in high conductivity.
- 11 October 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (43) , 23155-23164
Electronic structure manipulation via composition tuning for the development of highly conductive and acid-stable oxides
Exploring materials that simultaneously possess high conductivity and electrochemical stability is critical for various energy-conversion applications. In this study, our combined computations and experiments suggest the Mg–Ti–O chemical space for novel ternary oxide compounds offering high electrical conductivity and corrosion stability in acidic conditions to be potentially used as catalyst supporter of polymer electrolyte membrane fuel cells. High electrical conductivity (6.09 × 10−1 S cm−1) is achieved at room temperature by tuning the chemical composition of Mg1−xTi2+xO5 while still maintaining good corrosion stability (1.2 × 10−4 mA cm−2 after six days) in acidic conditions. Furthermore, we discover that a reducing gas environment during the synthesis increases the Ti solubility in Mg1−xTi2+xO5 with a reduced valence state of Ti, thus resulting in high conductivity.
- Open Access
- 25 May 2022
- Published by Springer Nature in Scientific Data
- Vol. 9 (1) , 1-11
Dataset of solution-based inorganic materials synthesis procedures extracted from the scientific literature
The development of a materials synthesis route is usually based on heuristics and experience. A possible new approach would be to apply data-driven approaches to learn the patterns of synthesis from past experience and use them to predict the syntheses of novel materials. However, this route is impeded by the lack of a large-scale database of synthesis formulations. In this work, we applied advanced machine learning and natural language processing techniques to construct a dataset of 35,675 solution-based synthesis procedures extracted from the scientific literature. Each procedure contains essential synthesis information including the precursors and target materials, their quantities, and the synthesis actions and corresponding attributes. Every procedure is also augmented with the reaction formula. Through this work, we are making freely available the first large dataset of solution-based inorganic materials synthesis procedures.
- 25 May 2022
- Published by Springer Nature in Scientific Data
- Vol. 9 (1) , 1-11
Open AccessDataset of solution-based inorganic materials synthesis procedures extracted from the scientific literature
The development of a materials synthesis route is usually based on heuristics and experience. A possible new approach would be to apply data-driven approaches to learn the patterns of synthesis from past experience and use them to predict the syntheses of novel materials. However, this route is impeded by the lack of a large-scale database of synthesis formulations. In this work, we applied advanced machine learning and natural language processing techniques to construct a dataset of 35,675 solution-based synthesis procedures extracted from the scientific literature. Each procedure contains essential synthesis information including the precursors and target materials, their quantities, and the synthesis actions and corresponding attributes. Every procedure is also augmented with the reaction formula. Through this work, we are making freely available the first large dataset of solution-based inorganic materials synthesis procedures.
- 17 April 2022
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (21)
Thermodynamically Driven Synthetic Optimization for Cation‐Disordered Rock Salt Cathodes
Relating the synthesis conditions of materials to their functional performance has long been an experience‐based trial‐and‐error process. However, this methodology is not always efficient in identifying an appropriate protocol and can lead to overlooked opportunities for the performance optimization of materials through simple modifications of the synthesis process. In this work, the authors systematically track the structural evolution in the synthesis of a representative disordered rock salt (a promising next‐generation Li‐ion cathode material) at the scale of both the long‐range crystal structure and the short‐range atomic structure using various in situ and ex situ techniques, including transmission electron microscopy, X‐ray diffraction, and pair distribution function analysis. An optimization strategy is proposed for the synthesis protocol, leading to a remarkably enhanced capacity (specific energy) of 313 mAh g−1 (987 Wh kg−1) at a low rate (20 mA g−1), with a capacity of more than 140 mAh g−1 retained even at a very high cycling rate of 2000 mA g−1. This strategy is further rationalized using ab initio calculations, and important opportunities for synthetic optimization demonstrated in this study are highlighted.
- 17 April 2022
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (21)
Thermodynamically Driven Synthetic Optimization for Cation‐Disordered Rock Salt Cathodes
Relating the synthesis conditions of materials to their functional performance has long been an experience‐based trial‐and‐error process. However, this methodology is not always efficient in identifying an appropriate protocol and can lead to overlooked opportunities for the performance optimization of materials through simple modifications of the synthesis process. In this work, the authors systematically track the structural evolution in the synthesis of a representative disordered rock salt (a promising next‐generation Li‐ion cathode material) at the scale of both the long‐range crystal structure and the short‐range atomic structure using various in situ and ex situ techniques, including transmission electron microscopy, X‐ray diffraction, and pair distribution function analysis. An optimization strategy is proposed for the synthesis protocol, leading to a remarkably enhanced capacity (specific energy) of 313 mAh g−1 (987 Wh kg−1) at a low rate (20 mA g−1), with a capacity of more than 140 mAh g−1 retained even at a very high cycling rate of 2000 mA g−1. This strategy is further rationalized using ab initio calculations, and important opportunities for synthetic optimization demonstrated in this study are highlighted.