Amar Bouazzouni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Amar Bouazzouni has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Magd Abdel Wahab
Ghent University
5 shared publications - Samir Tiachacht
Laboratory of Mechanics, Structure and Energetics (LMSE), Mouloud Mammeri University of Tizi-Ouzou, Tizi Ouzou, Algeria
5 shared publications - Yunlai Zhou
State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace Engineering, Xi’an Jiaotong University, Xi’an 710049, China
4 shared publications A. Behtani
3 shared publicationsS. Khatir
3 shared publicationsS Khatir
Department of Electrical energy, Systems and Automation, Faculty of Engineering and Architecture, Ghent University, Belgium
2 shared publications
Latest Publications
- 1 December 2018
- Published by Elsevier in Engineering Structures
- Vol. 177, 421-430
Damage assessment in structures using combination of a modified Cornwell indicator and genetic algorithm
- 1 December 2018
- Published by Elsevier in Engineering Structures
- Vol. 177, 421-430
Damage assessment in structures using combination of a modified Cornwell indicator and genetic algorithm
- Open Access
- 15 February 2018
- Published by JVE International Ltd. in Journal of Vibroengineering
- Vol. 20 (1) , 202-214
Structural health monitoring of 3D frame structures using finite element modal analysis and genetic algorithm
In this paper, we present a new application based on Genetic Algorithm (GA) to detect damage in 3D frame structures. Finite Element Method (FEM) is used to build models for intact and damaged structures. The identification of damage is formulated as an optimization problem using GA and the changes in natural frequencies. A 3D frame structure with two floor is used, as a numerical example, for damage identification. The proposed method is then applied to identify some removed elements. The results obtained using FEM is validated using experimental benchmark test of a 3D frame structure with eight floors. The results show that the proposed technique gives good damage identification compared with literature [1]. Furthermore, there is no error recorded in the prediction of location, however a small error is recorded in detecting damage severity. It is concluded that GA is an efficient tool to quantify single and multiple damages with high precision in 3D frame structures.
- 15 February 2018
- Published by JVE International Ltd. in Journal of Vibroengineering
- Vol. 20 (1) , 202-214
Open AccessStructural health monitoring of 3D frame structures using finite element modal analysis and genetic algorithm
In this paper, we present a new application based on Genetic Algorithm (GA) to detect damage in 3D frame structures. Finite Element Method (FEM) is used to build models for intact and damaged structures. The identification of damage is formulated as an optimization problem using GA and the changes in natural frequencies. A 3D frame structure with two floor is used, as a numerical example, for damage identification. The proposed method is then applied to identify some removed elements. The results obtained using FEM is validated using experimental benchmark test of a 3D frame structure with eight floors. The results show that the proposed technique gives good damage identification compared with literature [1]. Furthermore, there is no error recorded in the prediction of location, however a small error is recorded in detecting damage severity. It is concluded that GA is an efficient tool to quantify single and multiple damages with high precision in 3D frame structures.
- Open Access
- 15 November 2017
- Published by JVE International Ltd. in Journal of Vibroengineering
- Vol. 19 (7) , 4977-4988
Damage localization and quantification of composite beam structures using residual force and optimization
Structural Health Monitoring (SHM) and impact monitoring of composite structures have become important research topics in the recent year. In this research, a non-destructive vibration-based damage detection method is formulated using Genetic Algorithm (GA) and compared with classical method. The robustness and reliability of the capability to locate and to estimate the severity of damage, based on changes in dynamic characteristics of a structure, is investigated. The objective function for the damage identification problem is established by using the residual force method (FRM). Numerical experiments using finite element analysis are performed on composite beams with different damage scenarios in order to clarify the validity of the developed technique. The comparison between estimated and real damage illustrates the efficiency of the algorithm in damage detection. The results show that the present approach is correct and efficient for detecting structural local damages in composite beam structures.
- 15 November 2017
- Published by JVE International Ltd. in Journal of Vibroengineering
- Vol. 19 (7) , 4977-4988
Open AccessDamage localization and quantification of composite beam structures using residual force and optimization
Structural Health Monitoring (SHM) and impact monitoring of composite structures have become important research topics in the recent year. In this research, a non-destructive vibration-based damage detection method is formulated using Genetic Algorithm (GA) and compared with classical method. The robustness and reliability of the capability to locate and to estimate the severity of damage, based on changes in dynamic characteristics of a structure, is investigated. The objective function for the damage identification problem is established by using the residual force method (FRM). Numerical experiments using finite element analysis are performed on composite beams with different damage scenarios in order to clarify the validity of the developed technique. The comparison between estimated and real damage illustrates the efficiency of the algorithm in damage detection. The results show that the present approach is correct and efficient for detecting structural local damages in composite beam structures.
- Open Access
- 1 May 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 842 (1) , 012027
A proposal application based on strain energy for damage detection and quantification of beam composite structure using vibration data
In this research paper, the damage in Carbon Fibre Reinforced Polymer (CFRP) laminate beams under free vibration and simply supported conditions, is investigated numerically by Finite Element Method (FEM) using Matlab program. The developed Cornwell Indicator is used for damage detection and quantification in the considered composite beams. The data was acquired by developing a software that performs dynamic analysis of composite beams based on FEM. The results show that the efficiency of the developed indicator.
- 1 May 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 842 (1) , 012027
Open AccessA proposal application based on strain energy for damage detection and quantification of beam composite structure using vibration data
In this research paper, the damage in Carbon Fibre Reinforced Polymer (CFRP) laminate beams under free vibration and simply supported conditions, is investigated numerically by Finite Element Method (FEM) using Matlab program. The developed Cornwell Indicator is used for damage detection and quantification in the considered composite beams. The data was acquired by developing a software that performs dynamic analysis of composite beams based on FEM. The results show that the efficiency of the developed indicator.
- Open Access
- 1 May 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 842 (1) , 012028
Damage localization and quantification of composite stratified beam Structures using residual force method
In this paper, the problem of using measured modal parameters to detect and locate damage in beam composite stratified structures with four layers of graphite/epoxy [0°/902°/0°] is investigated. A technique based on the residual force method is applied to composite stratified structure with different boundary conditions, the results of damage detection for several damage cases demonstrate that using residual force method as damage index, the damage location can be identified correctly and the damage extents can be estimated as well.
- 1 May 2017
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 842 (1) , 012028
Open AccessDamage localization and quantification of composite stratified beam Structures using residual force method
In this paper, the problem of using measured modal parameters to detect and locate damage in beam composite stratified structures with four layers of graphite/epoxy [0°/902°/0°] is investigated. A technique based on the residual force method is applied to composite stratified structure with different boundary conditions, the results of damage detection for several damage cases demonstrate that using residual force method as damage index, the damage location can be identified correctly and the damage extents can be estimated as well.
- 1 April 2012
- Published by Elsevier in Composite Structures
- Vol. 94 (5) , 1805-1813
Perturbed solution of free non-linear vibrations of composite beams
- 1 April 2012
- Published by Elsevier in Composite Structures
- Vol. 94 (5) , 1805-1813
Perturbed solution of free non-linear vibrations of composite beams
- Open Access
- 1 January 2005
- Published by Hindawi Limited in Shock and Vibration
- Vol. 12 (5) , 377-388
Finite Element Model Updating Using FRF Measurements
This study presents a new updating method based on measured frequency response functions. The objective function of the minimization procedure is formed by the difference between the measured and the analytical frequency responses. The updating parameters are the correction coefficients related to each the elementary mass and stiffness matrices. While making use of a number of incomplete measurements for some frequencies, one builds a non-linear system of equations. The linearisation of the numerical system leads to an iterative procedure. An intrinsic frequency parametrization is proposed in order to accelerate the convergence of the iterative system. The obtained results are comparable with those of the known least squares methods.
- 1 January 2005
- Published by Hindawi Limited in Shock and Vibration
- Vol. 12 (5) , 377-388
Open AccessFinite Element Model Updating Using FRF Measurements
This study presents a new updating method based on measured frequency response functions. The objective function of the minimization procedure is formed by the difference between the measured and the analytical frequency responses. The updating parameters are the correction coefficients related to each the elementary mass and stiffness matrices. While making use of a number of incomplete measurements for some frequencies, one builds a non-linear system of equations. The linearisation of the numerical system leads to an iterative procedure. An intrinsic frequency parametrization is proposed in order to accelerate the convergence of the iterative system. The obtained results are comparable with those of the known least squares methods.