Валентин Алексієвець
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Валентин Алексієвець has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Andrii Ivaniuk
Національний університет водного господарства та природокористування
3 shared publications - I I Aleksiievets
Національний університет водного господарства та природокористування
3 shared publications S I Roshchina
2 shared publicationsA A Koshcheev
1 shared publicationA M Ivaniuk
1 shared publication- Alesya Romanovich
Vladimir State University named after Alexander and Nikolay Stoletovs
1 shared publication
Latest Publications
- 4 December 2025
- Published by National University of Water and Environmental Engineering in Ресурсоекономні матеріали, конструкції, будівлі та споруди
- No. 48,p. 171-177
ЩОДО АНАЛІЗУ ДОСЛІДЖЕНЬ РОБОТИ, РОЗРАХУНКІВ ТА НАПРУЖЕНОГО СТАНУ НАГЕЛЬНИХ З'ЄДНАНЬ ДЕРЕВ'ЯНИХ КОНСТРУКЦІЇ. РОЗРАХУНОК НАГЕЛЬНИХ З'ЄДНАНЬ «СТАЛЬ-ДЕРЕВИНА»
Наведено результати огляду досліджень вітчизняних та закордонних науковців, щодо роботи, розрахунку та напружено-деформованого стану дерев'яних конструкцій за різних видів навантаження. Більш детально зроблено акцентування на дослідження нагельних з'єднань дерев'яних конструкцій, для подальшого дослідження з’єднань типу «деревина сталь».
- 4 December 2025
- Published by National University of Water and Environmental Engineering in Ресурсоекономні матеріали, конструкції, будівлі та споруди
- No. 48,p. 171-177
ЩОДО АНАЛІЗУ ДОСЛІДЖЕНЬ РОБОТИ, РОЗРАХУНКІВ ТА НАПРУЖЕНОГО СТАНУ НАГЕЛЬНИХ З'ЄДНАНЬ ДЕРЕВ'ЯНИХ КОНСТРУКЦІЇ. РОЗРАХУНОК НАГЕЛЬНИХ З'ЄДНАНЬ «СТАЛЬ-ДЕРЕВИНА»
Наведено результати огляду досліджень вітчизняних та закордонних науковців, щодо роботи, розрахунку та напружено-деформованого стану дерев'яних конструкцій за різних видів навантаження. Більш детально зроблено акцентування на дослідження нагельних з'єднань дерев'яних конструкцій, для подальшого дослідження з’єднань типу «деревина сталь».
- 1 August 2022
- Published by National University of Water and Environmental Engineering in Ресурсоекономні матеріали, конструкції, будівлі та споруди
- No. 40,p. 73-78
КОНСТРУКТИВНІ РІШЕННЯ, РОЗРАХУНОК ТА ЗАСТОСУВАННЯ КЛЕЄНИХ ДЕРЕВ'ЯНИХ КОНСТРУКЦІЙ В БУДІВЛЯХ ГРОМАДСЬКОГО ПРИЗНАЧЕННЯ
Наведено результати розрахунку, проектування та застосуваннядерев'яних конструкцій напіврамного типу в будівлі з середнімипрольотами. Запропонована конструктивна схема напіврами з клеєнихдерев'яних конструкцій, що забезпечує необхідну надійність в процесіексплуатації будівлі.
- 1 August 2022
- Published by National University of Water and Environmental Engineering in Ресурсоекономні матеріали, конструкції, будівлі та споруди
- No. 40,p. 73-78
КОНСТРУКТИВНІ РІШЕННЯ, РОЗРАХУНОК ТА ЗАСТОСУВАННЯ КЛЕЄНИХ ДЕРЕВ'ЯНИХ КОНСТРУКЦІЙ В БУДІВЛЯХ ГРОМАДСЬКОГО ПРИЗНАЧЕННЯ
Наведено результати розрахунку, проектування та застосуваннядерев'яних конструкцій напіврамного типу в будівлі з середнімипрольотами. Запропонована конструктивна схема напіврами з клеєнихдерев'яних конструкцій, що забезпечує необхідну надійність в процесіексплуатації будівлі.
- 29 July 2022
- Published by National University of Water and Environmental Engineering in Ресурсоекономні матеріали, конструкції, будівлі та споруди
- No. 41,p. 267-275
ОСОБЛИВОСТІ РОБОТИ БУРОІН’ЄКЦІЙНИХ ПАЛЬ В НЕСТІЙКОМУ ВОДОНАСИЧЕНОМУ ҐРУНТІ
Наведено результати розрахунку, проектування та застосування буроін’єкційних паль в нестійких водонасичених ґрунтах на прикладі об’єкту проектування та реконструкції стадіону «Авангард» в м. Рівне. Виконані статичні випробування буроін’єкційних паль та підтверджено збільшення значень фактичної несучої здатності паль відносно розрахункової.
- 29 July 2022
- Published by National University of Water and Environmental Engineering in Ресурсоекономні матеріали, конструкції, будівлі та споруди
- No. 41,p. 267-275
ОСОБЛИВОСТІ РОБОТИ БУРОІН’ЄКЦІЙНИХ ПАЛЬ В НЕСТІЙКОМУ ВОДОНАСИЧЕНОМУ ҐРУНТІ
Наведено результати розрахунку, проектування та застосування буроін’єкційних паль в нестійких водонасичених ґрунтах на прикладі об’єкту проектування та реконструкції стадіону «Авангард» в м. Рівне. Виконані статичні випробування буроін’єкційних паль та підтверджено збільшення значень фактичної несучої здатності паль відносно розрахункової.
- 18 March 2022
- Published by Springer Nature
- p. 1459-1466
Geodesic Domes with Installing Floor Using a Cable Stay System
- 18 March 2022
- Published by Springer Nature
- p. 1459-1466
Geodesic Domes with Installing Floor Using a Cable Stay System
- Open Access
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 896 (1)
Load-carrying capacity of bolted joints of timber structures under static loading
The paper is devoted to the study of the single loads effect on the load-carrying capacity and deformability of bolted joints of wooden structures. The introduction substantiates the relevance of the topic, gives a general description of the work, its scientific novelty and practical value. The authors propose an experimental technique for determining the load-carrying capacity of bolted joints when separating the deformation of the dowel hole and that of tensile strain of bolts. The operation of such joints was experimentally and theoretically investigated. The study resulted in statistical confirmation of satisfactory convergence between the theoretical data obtained by the proposed method and the experimental data of the authors, as well as the recommendations on practical application of the suggested calculation method were developed. The deformations of the bolt and the wood were experimentally separated, the diagrams of the deformation of the stretched zone of the bolt were made, and the percentage ratio of the bolt deformations to the total deformations of the entire joint was calculated. To describe the process of the bolt joint deformation due to the action of single static loads, it is recommended to use a hyperbolic dependence, which well reflects the relationship between the load-strain values (F-Δ). A new method is proposed for calculating the bearing capacity of bolted joints, which is based on the use of the initial modulus of strain capacity E0 and the strain capacity coefficient of the joint β. According to this technique, the load-carrying capacity of bolted joints with various geometric characteristics was calculated. The ratio of theoretical values of load-carrying capacity to the experimental values by, on average, 30% showed a greater convergence when compared to the load-carrying capacity calculated according to the current regulatory documents.
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 896 (1)
Open AccessLoad-carrying capacity of bolted joints of timber structures under static loading
The paper is devoted to the study of the single loads effect on the load-carrying capacity and deformability of bolted joints of wooden structures. The introduction substantiates the relevance of the topic, gives a general description of the work, its scientific novelty and practical value. The authors propose an experimental technique for determining the load-carrying capacity of bolted joints when separating the deformation of the dowel hole and that of tensile strain of bolts. The operation of such joints was experimentally and theoretically investigated. The study resulted in statistical confirmation of satisfactory convergence between the theoretical data obtained by the proposed method and the experimental data of the authors, as well as the recommendations on practical application of the suggested calculation method were developed. The deformations of the bolt and the wood were experimentally separated, the diagrams of the deformation of the stretched zone of the bolt were made, and the percentage ratio of the bolt deformations to the total deformations of the entire joint was calculated. To describe the process of the bolt joint deformation due to the action of single static loads, it is recommended to use a hyperbolic dependence, which well reflects the relationship between the load-strain values (F-Δ). A new method is proposed for calculating the bearing capacity of bolted joints, which is based on the use of the initial modulus of strain capacity E0 and the strain capacity coefficient of the joint β. According to this technique, the load-carrying capacity of bolted joints with various geometric characteristics was calculated. The ratio of theoretical values of load-carrying capacity to the experimental values by, on average, 30% showed a greater convergence when compared to the load-carrying capacity calculated according to the current regulatory documents.
- Open Access
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 896 (1)
Local deformation and strength characteristics of S-shaped reinforcement in wood
Reinforced wooden beam structures under the influence of critical loads are subject to brittle fracture, which is dangerous when operating beams in buildings. To solve this problem, reinforcement of wooden beams for civil and industrial buildings was invented using steel rope as a reinforcing element. The rope is located in the stretched area of the beams along the original S-shaped trajectory. Numerical studies of the deformation of the reinforcement model using the LIRA program are performed. Based on numerical studies, samples were made for testing for pulling S-shaped anchoring elements from solid wood. The analysis of deformation - strength characteristics based on the results of tests on a tensile testing machine glued curved rods. A triple increase in the ductility of the deformation of the paste in the zone of destructive loads was revealed. The main problems of this type of reinforcement are the appearance of stress concentrators in areas with a small radius of curvature of the reinforcement. As a result of the study, the optimal trajectory of the reinforcement insert was determined with the aim of obtaining higher strength and deformation characteristics - with a reduced oscillation amplitude. The possibility of using structures in the form of safety elements has been established, which allows to increase the destruction time of beam systems when exceeding the permissible load.
- 1 July 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 896 (1)
Open AccessLocal deformation and strength characteristics of S-shaped reinforcement in wood
Reinforced wooden beam structures under the influence of critical loads are subject to brittle fracture, which is dangerous when operating beams in buildings. To solve this problem, reinforcement of wooden beams for civil and industrial buildings was invented using steel rope as a reinforcing element. The rope is located in the stretched area of the beams along the original S-shaped trajectory. Numerical studies of the deformation of the reinforcement model using the LIRA program are performed. Based on numerical studies, samples were made for testing for pulling S-shaped anchoring elements from solid wood. The analysis of deformation - strength characteristics based on the results of tests on a tensile testing machine glued curved rods. A triple increase in the ductility of the deformation of the paste in the zone of destructive loads was revealed. The main problems of this type of reinforcement are the appearance of stress concentrators in areas with a small radius of curvature of the reinforcement. As a result of the study, the optimal trajectory of the reinforcement insert was determined with the aim of obtaining higher strength and deformation characteristics - with a reduced oscillation amplitude. The possibility of using structures in the form of safety elements has been established, which allows to increase the destruction time of beam systems when exceeding the permissible load.