Małgorzata Kawalec
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Małgorzata Kawalec has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Andrzej Gradzik
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, Powstańców Warszawy 12, 35-959 Rzeszow, Poland
1 shared publication - Andrzej Kawalec
Department of Manufacturing Techniques and Automation, Faculty of Mechanical Engineering and Aeronautics, Rzeszów University of Technology, 35-029 Rzeszów, Poland
1 shared publication - Andrzej Pacana
Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszów, Poland
1 shared publication - Anna Bazan
Department of Manufacturing Techniques and Automation, Rzeszów University of Technology, 35-959 Rzeszów, Poland
1 shared publication - Artur Szajna
Department of Manufacturing Techniques and Automation, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Al. Powstancow Warszawy Street, 35-959 Rzeszow, Poland
1 shared publication - Barbara Kościelniak
Department of Materials Science, The Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, 12 Powstancow Warszawy Ave., 35-959 Rzeszow, Poland
1 shared publication
Latest Publications
- Open Access
- 1 December 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (8) , 181-190
The Effect of Milling Parameters of Vanadis 4 Extra Steel on Cutting Force Values and Roughness of Machined Surface
The article presents the results of experimental studies of the milling process of Vanadis 4 Extra - tool steel 1.2210 with a four-flute AlCrN-coated end mill. On the basis of the measured values of the total cutting force F and the roughness parameters Ra and Rz of machined surfaces, the...
- 1 December 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (8) , 181-190
Open AccessThe Effect of Milling Parameters of Vanadis 4 Extra Steel on Cutting Force Values and Roughness of Machined Surface
The article presents the results of experimental studies of the milling process of Vanadis 4 Extra - tool steel 1.2210 with a four-flute AlCrN-coated end mill. On the basis of the measured values of the total cutting force F and the roughness parameters Ra and Rz of machined surfaces, the...
- Open Access
- 1 February 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (1) , 291-305
The Effect of Re Content on Microstructure and Creep Resistance of Single Crystal Castings Made of Nickel-Based Superalloys
In this work the effect of crystal structure perfection on the creep resistance of single crystal superalloys. The CMSX-4 and CMSX-4®Plus with increased Re content is analyzed. Single crystal rods are made by directional solidification process at the withdrawal rates 3 and 5 mm/min. The...
- 1 February 2024
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 18 (1) , 291-305
Open AccessThe Effect of Re Content on Microstructure and Creep Resistance of Single Crystal Castings Made of Nickel-Based Superalloys
In this work the effect of crystal structure perfection on the creep resistance of single crystal superalloys. The CMSX-4 and CMSX-4®Plus with increased Re content is analyzed. Single crystal rods are made by directional solidification process at the withdrawal rates 3 and 5 mm/min. The...
- Open Access
- 1 May 2021
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 3 (1) , 79-88
Influence of Technical Condition of Control and Measurement Equipment on Calibration Results
In the paper there are analyzed the procedures used in the process of calibrating concerning control and measurement equipment. There was assumed the mathematical model of the measuring instrument which was then analyzed. The factors that result from the imperfect technical condition of the control and measurement equipment and may have an impact on the measurement results were also analyzed. Models of errors’ models were assumed that may affect the calibration results. The static calibration of control and measurement equipment was analyzed. The results of numerical simulations concerning the static calibration of control and measurement equipment were presented, taking into account the linear and non-linear processing functions of the measurement equipment. The results of computations obtained for various models of processing functions were compared with each other and conclusions were drawn regarding the accuracy of the mapping of the measured quantity.
- 1 May 2021
- Published by Walter de Gruyter GmbH in System Safety: Human - Technical Facility - Environment
- Vol. 3 (1) , 79-88
Open AccessInfluence of Technical Condition of Control and Measurement Equipment on Calibration Results
In the paper there are analyzed the procedures used in the process of calibrating concerning control and measurement equipment. There was assumed the mathematical model of the measuring instrument which was then analyzed. The factors that result from the imperfect technical condition of the control and measurement equipment and may have an impact on the measurement results were also analyzed. Models of errors’ models were assumed that may affect the calibration results. The static calibration of control and measurement equipment was analyzed. The results of numerical simulations concerning the static calibration of control and measurement equipment were presented, taking into account the linear and non-linear processing functions of the measurement equipment. The results of computations obtained for various models of processing functions were compared with each other and conclusions were drawn regarding the accuracy of the mapping of the measured quantity.