AKAleksandr A. Khodyakov

Aleksandr A. Khodyakov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Aleksandr A. Khodyakov has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Toxicity of a gasoline engine for small-scale mechanization

    by Alexander A. Khodyakov, Sergey V. Khlopkov, Danil V. Istomin, Djeqran R. Alibekova, Alexey A. Narozhnyy, Ходяков Александр Андреевич, Хлопков Сергей Валентинович, Нарожный Алексей Алексеевич

    The single-cylinder, four-stroke, overhead valve Biggs Stratton engine was studied for the possible toxinity with the view of solving the environmental pollution problem related to the internal combustion engine emissions. As an assessment of toxicity, the data recorded (INFRACAR 5M3T) in the exhaust gases of the power unit NOx, CO and CH was used. Evaluation of the toxicity of the engine running under load was carried out by testing (CARTEC LPS 2510 dynamometer) an engine-equipped vehicle of simplified design (buggy). It was shown that the presence of CO, CH and NOx in the exhaust gases is affected not only by the presence of alcohol in gasoline, but also by the crankshaft speed. It was found that the proportion of CH in the exhaust gases of the power unit running on gasoline is lower than the maximum allowable content of hydrocarbons in the exhaust gases of gasoline engines not equipped with a neutralization system. According to the data obtained from bench tests, it follows that the proportion of CH in the exhaust gases of a gasoline-fueled engine is on average 48% higher than in the exhaust gases of an engine fed with a gasoline-alcohol mixture. It was shown that a significant increase in power at the wheel does not lead to a sharp increase in the CH content in the exhaust gases. The proportion of CH in the exhaust gases in the obtained speed range is a constant value.

  • Open Access

    Physical and chemical properties of innovative and high-quality grades of gasoline

    by Alexander A. Khodyakov, Sergey V. Khlopkov, Artur R. Asoyan, Danil V. Istomin, Djeqran R. Alibekova, Alexey A. Narozhnyi, Ходяков Александр Андреевич, Хлопков Сергей Валентинович, Нарожный Алексей Алексеевич

    Studies of the physicochemical properties of traditional gasoline (G), innovative gasoline (IG) and high-quality gasoline (HQG) have been carried out. The purpose of this work was to analyze the physicochemical properties of innovative, high-quality grades of gasoline, to compare the performance of these fuels with those of conventional fuel that does not contain substances that improve the operational and environmental qualities. The research of the properties of gasolines was carried out using an automatic apparatus for distillation of petroleum products ARNS-1E, indicator (octanometer) OKTAN-IM, gas analyzer INFRACAR 5M3T, single-cylinder, 4-stroke, overhead valve engine (Biggs Stratton). It has been established that the density of gasolines, the final boiling point, the residue in the flask and the acidity correspond to the GOST standards. A six-month storage period for fuel samples does not affect the parameters of the fuel, its physical and chemical stability. It is shown that substances that improve the properties of innovative and high-quality fuels do not affect the result of measuring the octane number of gasoline. It has been established that the chemical stability of improved grades of gasoline is higher than that of traditional fuel. It is shown that innovative and high-quality gasoline is superior to gasolines that do not contain combustion-improving substances in terms of combustion efficiency. A similar conclusion was made for nitrogen oxides, the content of which is associated with the presence in gasoline of components that increase the temperature of gases that occur in the combustion chamber of the power unit.

  • Open Access

    Evaluation of the technical condition of electromagnetic injectors on the test bench according to the error in measuring the flow rate of the test liquid

    by Aleksandr A. Khodyakov, Sergey V. Khlopkov, Vlada V. Basova, Oleg I. Telkov, Anastasia D. Kosmacheva, Хлопков Сергей Валентинович

    It has been established that the average values of the error in measuring the flow rate of the test liquid (TL) by electromagnetic injectors (EMI) are associated with the vehicle mileage. The greater the mileage, the higher the value of the error. It is shown that the dependence of the error in measuring the flow rate on the run can be described in a rough approximation by regression. The technical condition of the EMI was assessed by an instrument for cleaning and analyzing fuel injectors HP-6V, complete with an Ultrasonic Cleaner ultrasonic bath. The objects of study are the EMI of gasoline engines with distributed fuel injection. The injectors were used in the power units of GAZ-27040 V (“Gazelle”), ZAZ Chance SX, VAZ 2121 (“Niva”), Chevrolet Lacetti and others, mileage from 0 to 188 thousand km. Siemens DEKA ZMZ 6354, Siemens DEKA VAZ 6238, Siemens DEKA VAZ 20734, Siemens DEKA VAZ 20735, Bosch 0 280 158 502, Bosch 0 280 158 017, Bosch 0 280 158 022, Bosch 0 280 150 9925, Denso 23925 injectors tested.

  • Open Access

    Evaluation of the gasoline electromagnetic injectors performance by the average absolute deviation values of the test liquid volume

    by Aleksandr A. Khodyakov, Sergey V. Khlopkov, Vlada V. Basova, Хлопков Сергей Валентинович

    An assessment of the technical condition of electromagnetic injectors (EMI) of gasoline engines with direct fuel injection has been carried out. The technical condition of the EMI was assessed using a stand for cleaning and testing injectors. A step-by-step cleaning of the nozzles from contamination was used, that is, in two stages. At the first stage, the “extra flushing” mode (without ultrasound) was applied. The detergent for this cleaning method was anhydrous BG-210 washing liquid, consisting of hydrotreated heavy and light oils, Stoddard’s solvent, 2-butoxyethanol, isopropyl alcohol, and xylene. At the second stage, the nozzles were cleaned for 10 minutes in an ultrasonic bath filled with LAVR Ln 2003 washing liquid. It is shown that the calculated average absolute deviations of the test liquid volume reflect not only the presence of contaminants in the nozzles, but also illustrates the cleaning process. The average absolute deviations of the volume of the test liquid after chemical treatment and exposure to ultrasound are 2-9 times lower than those obtained in nozzles that were not cleaned with chemical reagents and ultrasound.

  • Open Access

    Analysis of antifreeze properties before and after their operation in engine

    by Oleg I. Telkov, Anastasia D. Kosmacheva, Aleksandr A. Khodyakov, Sergey V. Khlopkov, Igor K. Danilov, Хлопков Сергей Валентинович

    The results of diagnostics of antifreeze indicators before and after their operation in an internal combustion engine are presented. The chosen direction of research is relevant, since it allows one to predict not only the change in the properties of antifreeze during its operation, but also to obtain evidence of the course of metal corrosion processes. The purpose of the study - to conduct control tests of antifreezes before and after their operation in an internal combustion engine, that ensures the maintenance of the power unit in good condition. The objects of study were fresh AGA Z-40-G12++ antifreeze (release of 2021; A-21) and coolant AGA Z-40-G12+ (release of 2012; AE-12) after its operation for several years. It is shown that the pH, density, viscosity, electrical conductivity of the coolant samples before and after its operation are different. It was found that the course of the dependences of electrical conductivity on temperature t for samples A-21 and AE-12 is the same. The dependence of on t is described by a polynomial (quadratic) model. It has been suggested that higher values of the AE-12 hydrogen index may indicate the occurrence of electrochemical corrosion of metals, which, in the process of contact with antifreeze, form short-circuited galvanic pairs. With the help of a complete factorial experiment, it was demonstrated that higher pH values of used antifreeze can be a reflection of the degradation of the properties of monoethylene glycol and the ongoing processes of metal corrosion.

  • Open Access

    Effect of gasoline composition on the absorption and retention of fuel vapor by activated carbon of the automobile adsorber

    by A A Khodyakov, S V Khlopkov, A V Azanov, R Kh Abu-Nidzhim

    The physicochemical characteristics of petrol samples are studied. It is established that the fuel purchased at fuel stations corresponds to the standard parameters presented in the EURO standard for unleaded petrol. The presence of saturated hydrocarbons in petrol is determined using concentrated sulfuric acid, which reacts with unsaturated (alkenes, olefins) and aromatic hydrocarbons, without reacting with saturated hydrocarbons. The fractional composition of petrol samples is determined from the distillation temperatures measured by a mercury thermometer included in the automatic oil distillation apparatus ARNS-1E, acidity titration with an alcohol solution of potassium hydroxide gasoline mixtures with 80% ethanol. An acid-base phenolphthalein indicator (pH = 8.0-9.6) is used to indicate an excess of OH−. The density of the fuel samples is measured with oleometers (densimeters), octane numbers (ON) - indicator (Octanometer) OKTAN-IM. The limit of the permissible absolute error of the measurement of ON is ± 2 octane units. It is established that all petrols without exception contain saturated, unsaturated and aromatic hydrocarbons. It is shown that of the seven samples studied, two samples have some peculiarities. It is concluded that when controlling the quality of fuel, it is necessary to take into account not only the conformity of the determined value to the parameter of the norm, but also the differences in the values of the indices obtained when testing a series of fuel samples.

  • Open Access

    Research of the effect of washing of fuel system engines on traction-speed properties of cars

    by S Khlopkov, I Danilov, A Khodyakov, A Azanov, S Borychev, I Uspensky, G Kokorev, I Yukhin, M Latyshenok, A Asoyan, et al.

    The results of tests on the Cartec LPS 2510 dynamometer stand (test mode P-max) according to ISO 1585 are presented. Regardless of car model, year of manufacture, mileage and engine size, power unit power loss and a decrease in torque are observed. Flushing the fuel system with special fluids and ultrasonic cleaning of the nozzles allow the restoration of engine power and torque.

  • Open Access

    Study of impact of tribotechnical composition on rubber technical products to assess its applicability in wheeled transport engine

    by A V Azanov, M V Azanov, A G Amosov, S V Khlopkov, A A Khodyakov

    Tribotechnical coating helps to reduce the friction factor and improves the performance of the internal-combustion engine, but in the process, the generic components of the engine oil and other additives interfuse together. Besides, the coating mixture excretes acids and can destroy general mechanical rubber goods and metals. For this research the oil-gasoline-resistant rubber was used which is half-disk shaped with the dimensions of 27x7x2 mm. These samples of rubber have been heated to 110°C and exposed to generic components of engine oil, tribotechnical coating «ACTIVE PLUS» and strong acid H2SO4. In the total, the volume of the tribotechnical coating and engine oil was approximately 1 % of strong acid H2SO4. The article describes most common properties of aged rubbers such as rubber hardness, resilience, elasticity after exposure to generic components of engine oil and its additives. Results were obtained in the laboratory where samples of rubber were exposed to heat, engine oil, tribotechnical coating in conditions of absence of mechanical load. This study has identified an important issue according to which sulfuric acid destroys the system of oil-ultrafine particles in the absence of swelling of rubber.