Lianjie Yue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Lianjie Yue has a total of 59 co-authors. Here are the top co-authors by number of shared publications:
- Hao Chen
State Key Laboratory of High Temperature Gas Dynamics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
9 shared publications - Qifan Zhang
Chinese Academy of Sciences
6 shared publications Xinyu Chang
Institute of Mechanics, Chinese Academy of Sciences
5 shared publications- Weihang Luo
State Key Laboratory of High Temperature Gas Dynamics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China
3 shared publications XinYu Chang
Institute of Mechanics, Chinese Academy of Sciences
3 shared publications- Chengming He
Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon 999077, Hong Kong
2 shared publications
Latest Publications
- Open Access
Influence of Total Temperature and Pressure on Ejector Flow Patterns in RBCC Engines
The Rocket-Based Combined Cycle (RBCC) engine is a promising propulsion system for hypersonic and space launch applications due to its capability to operate efficiently over a broad range of flight conditions. This study investigates the influence of total temperature and total pressure on flow patterns in the rocket-ejector mode of a RBCC engine using two-dimensional numerical simulations—a simplification that facilitates efficient parametric analysis while inherently omitting three-dimensional effects. The transition between stable and wavy flow patterns under the Diffusion and Afterburning (DAB) combustion mode is analyzed. Higher total temperatures enhance mixing efficiency but can induce wavy flow patterns, leading to potential instability. Conversely, increased total pressures promote stability through Fabri-choking mechanisms while reducing mixing efficiency by limiting entrainment capacity. A significant hysteresis effect is observed, where transition thresholds for stable and wavy states vary based on operational history. Key mechanisms contributing to this effect are discussed in depth, including momentum flux dynamics, Fabri-choking behavior, shock wave reformation, and mass and heat exchange processes. These findings provide critical insights for optimizing RBCC engine performance by balancing flow stability and mixing efficiency under varying conditions. This study’s insights into flow pattern dynamics, particularly the hysteresis effect, are crucial for developing robust control strategies and optimizing RBCC engine designs for hypersonic and space launch applications.
Open AccessInfluence of Total Temperature and Pressure on Ejector Flow Patterns in RBCC Engines
The Rocket-Based Combined Cycle (RBCC) engine is a promising propulsion system for hypersonic and space launch applications due to its capability to operate efficiently over a broad range of flight conditions. This study investigates the influence of total temperature and total pressure on flow patterns in the rocket-ejector mode of a RBCC engine using two-dimensional numerical simulations—a simplification that facilitates efficient parametric analysis while inherently omitting three-dimensional effects. The transition between stable and wavy flow patterns under the Diffusion and Afterburning (DAB) combustion mode is analyzed. Higher total temperatures enhance mixing efficiency but can induce wavy flow patterns, leading to potential instability. Conversely, increased total pressures promote stability through Fabri-choking mechanisms while reducing mixing efficiency by limiting entrainment capacity. A significant hysteresis effect is observed, where transition thresholds for stable and wavy states vary based on operational history. Key mechanisms contributing to this effect are discussed in depth, including momentum flux dynamics, Fabri-choking behavior, shock wave reformation, and mass and heat exchange processes. These findings provide critical insights for optimizing RBCC engine performance by balancing flow stability and mixing efficiency under varying conditions. This study’s insights into flow pattern dynamics, particularly the hysteresis effect, are crucial for developing robust control strategies and optimizing RBCC engine designs for hypersonic and space launch applications.
- 1 May 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (5)
Collision-induced spin-to-orbital angular momentum conversion between two spinning droplets of unequal sizes
This paper focuses on the numerical study on the phenomenon and mechanism of spin-to-orbital angular momentum conversion for the head-on collision between a spinning droplet and a non-spinning droplet of unequal sizes. The droplet deformation process was phenomenologically described, where the gas film suppresses the rotating flow inside the spinning droplet and, in turn, rotates the non-spinning droplet through its shearing effects. The gas film tends to be curved by the size disparity, leading to a more complex gas film flow. The hysteresis mechanism of spin-to-orbital angular momentum conversion was analyzed. The decrease in spin angular momentum and increase in orbital angular momentum have an upper limit as increasing the size ratio, which is attributed to the droplet deformation that is similar to a droplet impacting on a liquid film. In addition, a wider range of size ratio, Weber number, and droplet spin angular speed were discussed, where some numerical findings are significant to the angular momentum conversion coefficient modeling.
- 1 May 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (5)
Collision-induced spin-to-orbital angular momentum conversion between two spinning droplets of unequal sizes
This paper focuses on the numerical study on the phenomenon and mechanism of spin-to-orbital angular momentum conversion for the head-on collision between a spinning droplet and a non-spinning droplet of unequal sizes. The droplet deformation process was phenomenologically described, where the gas film suppresses the rotating flow inside the spinning droplet and, in turn, rotates the non-spinning droplet through its shearing effects. The gas film tends to be curved by the size disparity, leading to a more complex gas film flow. The hysteresis mechanism of spin-to-orbital angular momentum conversion was analyzed. The decrease in spin angular momentum and increase in orbital angular momentum have an upper limit as increasing the size ratio, which is attributed to the droplet deformation that is similar to a droplet impacting on a liquid film. In addition, a wider range of size ratio, Weber number, and droplet spin angular speed were discussed, where some numerical findings are significant to the angular momentum conversion coefficient modeling.
- 29 April 2025
- Published by Elsevier in Aerospace Science and Technology
- Vol. 163
Shock reflection with the influence of wave structures near the intersection point in confined-space double-wedge
- 29 April 2025
- Published by Elsevier in Aerospace Science and Technology
- Vol. 163
Shock reflection with the influence of wave structures near the intersection point in confined-space double-wedge
- 13 January 2025
- Published by Springer Nature in Theoretical and Computational Fluid Dynamics
- Vol. 39 (1) , 1-16
Simple shape model for normal shock trains in straight channels
- 13 January 2025
- Published by Springer Nature in Theoretical and Computational Fluid Dynamics
- Vol. 39 (1) , 1-16
Simple shape model for normal shock trains in straight channels
- Open Access
Mitigation of Shock-Induced Separation Using Square-Shaped Micro-Serrations—A Preliminary Study
Suppressing shock-induced flow separation has been a long-standing problem in the design of supersonic vehicles. To reduce the structural and design complexity of control devices, a passive control technique based on micro-serrations is proposed and its controlling effects are preliminarily investigated under test conditions in which the Mach number is 2.5 and the ramp creating an incident shock is 15 deg. Meanwhile, a vorticity-based criterion for assessing separation scales is developed to resolve the inapplicability of the zero skin friction criterion caused by wall unevenness. The simulations demonstrate that the height of the first stair significantly influences the separation length. Generally, the separation length is shorter at higher stairs, but when the height is greater than half of the thickness of the incoming boundary layer, the corresponding separation point moves upstream. A stair with a height of only 0.4 times the thickness of the boundary layer reduces the separation length by 2.69%. Further parametric analysis reveals that while the remaining serrations have limited effects on the flow separation, an optimization of their shape (depth and width) can create more favorable spanwise vortices and offer a modest improvement of the overall controlling performance. Compared to the plate case, a 9.13% reduction in the separation length can be achieved using a slightly serrated design in which the leading stair is 0.1 high and the subsequent serrations are 0.2 deep and 0.05 wide (nondimensionalized, with the thickness of the incoming boundary layer). Meanwhile, the micro-serration structure even brings less drag. Considering the minor modification to the structure, the proposed method has the potential for use in conjunction with other techniques to exert enhanced control on separations.
Open AccessMitigation of Shock-Induced Separation Using Square-Shaped Micro-Serrations—A Preliminary Study
Suppressing shock-induced flow separation has been a long-standing problem in the design of supersonic vehicles. To reduce the structural and design complexity of control devices, a passive control technique based on micro-serrations is proposed and its controlling effects are preliminarily investigated under test conditions in which the Mach number is 2.5 and the ramp creating an incident shock is 15 deg. Meanwhile, a vorticity-based criterion for assessing separation scales is developed to resolve the inapplicability of the zero skin friction criterion caused by wall unevenness. The simulations demonstrate that the height of the first stair significantly influences the separation length. Generally, the separation length is shorter at higher stairs, but when the height is greater than half of the thickness of the incoming boundary layer, the corresponding separation point moves upstream. A stair with a height of only 0.4 times the thickness of the boundary layer reduces the separation length by 2.69%. Further parametric analysis reveals that while the remaining serrations have limited effects on the flow separation, an optimization of their shape (depth and width) can create more favorable spanwise vortices and offer a modest improvement of the overall controlling performance. Compared to the plate case, a 9.13% reduction in the separation length can be achieved using a slightly serrated design in which the leading stair is 0.1 high and the subsequent serrations are 0.2 deep and 0.05 wide (nondimensionalized, with the thickness of the incoming boundary layer). Meanwhile, the micro-serration structure even brings less drag. Considering the minor modification to the structure, the proposed method has the potential for use in conjunction with other techniques to exert enhanced control on separations.
- Open Access
- 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
Self-similar unstart characteristics of supersonic contraction duct with an expansion corner
Inlet unstart is detrimental to hypersonic airbreathing flights. By unstart, we mean the separation-induced collapse of a supersonic duct flow. The unstart characteristics of a two-dimensional contraction duct with an expansion corner are numerically investigated to develop a universal prediction method and to determine the unstart mechanism. The unstart boundaries under varying contraction angles, entrance heights, and Reynolds numbers are obtained by translating the cowl plate. A self-similar empirical equation of unstart boundary that unifies multiple variables is proposed through similarity analysis. To estimate the unstart boundaries of large-angle ducts, the alternative area ratio is presented. Three types of unstarts are identified according to the distribution of the unstart boundaries and the evolution mechanism of separation region: the long-cowl, transitional, and short-cowl unstart. The long-cowl unstart stems from the mass flow limit at the throat, while the other two unstarts stem from the separation region growth. The wall pressure criteria for unstart are correlated with the dimensionless cowl length and the characteristic separation scale in the critical state to facilitate unstart detection. Moreover, the self-similar compression intensity is proposed to characterize the maximum pressure increase induced by the unit effective area contraction in the started state.
- 1 January 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (1)
Open AccessSelf-similar unstart characteristics of supersonic contraction duct with an expansion corner
Inlet unstart is detrimental to hypersonic airbreathing flights. By unstart, we mean the separation-induced collapse of a supersonic duct flow. The unstart characteristics of a two-dimensional contraction duct with an expansion corner are numerically investigated to develop a universal prediction method and to determine the unstart mechanism. The unstart boundaries under varying contraction angles, entrance heights, and Reynolds numbers are obtained by translating the cowl plate. A self-similar empirical equation of unstart boundary that unifies multiple variables is proposed through similarity analysis. To estimate the unstart boundaries of large-angle ducts, the alternative area ratio is presented. Three types of unstarts are identified according to the distribution of the unstart boundaries and the evolution mechanism of separation region: the long-cowl, transitional, and short-cowl unstart. The long-cowl unstart stems from the mass flow limit at the throat, while the other two unstarts stem from the separation region growth. The wall pressure criteria for unstart are correlated with the dimensionless cowl length and the characteristic separation scale in the critical state to facilitate unstart detection. Moreover, the self-similar compression intensity is proposed to characterize the maximum pressure increase induced by the unit effective area contraction in the started state.
- Open Access
- 1 September 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (9)
Spray combustion characteristics of a gas–liquid pintle injector with variable swirl intensities
The present paper experimentally verified and computationally explained an improved design concept of the spray combustion of a gas–liquid pintle injector with variable swirl intensities. By pintle injector, we mean a promising injector for the throttleable engines with variable thrust capacities, which features the moveable pintle continuously controlling the mass flow rates of fuel and oxidizer where the radial and axial flows encounter to form a spray cone and spray atomization. First, the cold flow test was conducted to study the swirl effects on the spray angle, followed by the combustion test to study the total pressure and the specific impulse under different swirl intensities. The results show that the swirl enhances the combustion performance by increasing the total pressure and specific impulse. Second, the swirl-assisted spray was numerically simulated based on a validated volume-of-fluid method to explain the experimental findings. The diameter distribution and spatial distribution of dispersed droplets were analyzed by the Sauter mean diameter (SMD) and the Voronoi tessellation, respectively. The results show that the swirl significantly promotes the breakup of liquid jet or film, producing smaller SMDs and a more uniform spatial distribution of dispersed droplets. The consolidated correlation between the non-reacting spray characteristics and the combustion performance suggests that the proposed methodology can be used to fast prescreen pintle injector designs.
- 1 September 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (9)
Open AccessSpray combustion characteristics of a gas–liquid pintle injector with variable swirl intensities
The present paper experimentally verified and computationally explained an improved design concept of the spray combustion of a gas–liquid pintle injector with variable swirl intensities. By pintle injector, we mean a promising injector for the throttleable engines with variable thrust capacities, which features the moveable pintle continuously controlling the mass flow rates of fuel and oxidizer where the radial and axial flows encounter to form a spray cone and spray atomization. First, the cold flow test was conducted to study the swirl effects on the spray angle, followed by the combustion test to study the total pressure and the specific impulse under different swirl intensities. The results show that the swirl enhances the combustion performance by increasing the total pressure and specific impulse. Second, the swirl-assisted spray was numerically simulated based on a validated volume-of-fluid method to explain the experimental findings. The diameter distribution and spatial distribution of dispersed droplets were analyzed by the Sauter mean diameter (SMD) and the Voronoi tessellation, respectively. The results show that the swirl significantly promotes the breakup of liquid jet or film, producing smaller SMDs and a more uniform spatial distribution of dispersed droplets. The consolidated correlation between the non-reacting spray characteristics and the combustion performance suggests that the proposed methodology can be used to fast prescreen pintle injector designs.
- 1 April 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (4)
Numerical study of periodic flame flashback in a cavity-based scramjet combustor
The periodic flame flashback phenomenon in an ethylene-fueled cavity-based scramjet combustor was numerically investigated by a three-dimensional unsteady Reynolds-averaged Navier–Stokes solver with two-step kinetics. The air inflow stagnation temperature is 1225 K, and its Mach number is 2.6. Spectral analyses revealed the combustion oscillations with flame flashbacks maintained in the separated scramjet mode with the establishment/vanishment of flow separation near the fuel injector, differing from previous studies of flame flashbacks connected to the ramjet/scramjet mode transitions. A mechanism with four evolution stages was proposed to elucidate the flow-flame interaction. In stage I, a rapid flame flashback upstream and shock-train extension were caused by the high-temperature induced auto-ignition tendency of well-mixed unburned gas in the near-sidewall low-speed region. In stage II, the combustion-induced back pressure and shock train gradually achieved an aerodynamic balance. The combustion flow barely changed in stage III. Meanwhile, a simplified model suggested that the gradual temperature rises occurring upstream of the cavity and away from the sidewall were caused by spanwise heat conduction. The higher temperatures would cause upstream flame propagation with enhanced heat release due to auto-ignition. However, the enhanced heat release occurred mostly in the subsonic flow, resulting in pressure decreases according to one-dimensional flow equations. A smaller near-sidewall separation was produced by the lower back-pressures, which prompted the rapid flame recession downstream in stage IV. Moreover, a simplified flame-spreading model was proposed to illuminate the flame propagation nature. The comparison of flame speeds with theoretical estimations indicated that the current flame was in the regime of turbulent flame propagation, rather than the C–J detonation or deflagration speculated in previous studies.
- 1 April 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (4)
Numerical study of periodic flame flashback in a cavity-based scramjet combustor
The periodic flame flashback phenomenon in an ethylene-fueled cavity-based scramjet combustor was numerically investigated by a three-dimensional unsteady Reynolds-averaged Navier–Stokes solver with two-step kinetics. The air inflow stagnation temperature is 1225 K, and its Mach number is 2.6. Spectral analyses revealed the combustion oscillations with flame flashbacks maintained in the separated scramjet mode with the establishment/vanishment of flow separation near the fuel injector, differing from previous studies of flame flashbacks connected to the ramjet/scramjet mode transitions. A mechanism with four evolution stages was proposed to elucidate the flow-flame interaction. In stage I, a rapid flame flashback upstream and shock-train extension were caused by the high-temperature induced auto-ignition tendency of well-mixed unburned gas in the near-sidewall low-speed region. In stage II, the combustion-induced back pressure and shock train gradually achieved an aerodynamic balance. The combustion flow barely changed in stage III. Meanwhile, a simplified model suggested that the gradual temperature rises occurring upstream of the cavity and away from the sidewall were caused by spanwise heat conduction. The higher temperatures would cause upstream flame propagation with enhanced heat release due to auto-ignition. However, the enhanced heat release occurred mostly in the subsonic flow, resulting in pressure decreases according to one-dimensional flow equations. A smaller near-sidewall separation was produced by the lower back-pressures, which prompted the rapid flame recession downstream in stage IV. Moreover, a simplified flame-spreading model was proposed to illuminate the flame propagation nature. The comparison of flame speeds with theoretical estimations indicated that the current flame was in the regime of turbulent flame propagation, rather than the C–J detonation or deflagration speculated in previous studies.
- 1 November 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (11) , 116103
Numerical study on wave configuration of wedge-induced oblique detonation wave: Reactive boundary layer effect
A numerical simulation solving the Reynolds-averaged Navier–Stokes equation is presented to investigate the initiation and evolution of the wedge-induced oblique detonation wave (ODW) with emphasis on the effects of the burning boundary layer. The nondimensional activation energy (Ea) is selected as the bifurcate parameter, which varies from 30 to 50. The largest induction ignition length behind the oblique shock/detonation wave is shown to be proportional to the Ea. The initiation of ODW can be attributed to the collision and diffraction of reactive waves. The wave configuration, a series of compression waves (or shock wave), is observed at the conjunction point of the burning boundary layer and combustion wave, which intensifies the pressure jump as increasing the Ea. The polar line analysis demonstrates that the pressure jump triggers the transition from regular reflection to Mach reflection near triple-point. The oscillations of the ODW wave structures, for example, the triple-point and Mach stem, can be attributed to the Rayleigh–Taylor instabilities developed on the reaction front of the boundary layer, which shall be appropriately suppressed to remain the steadiness of the ODW and flow configuration.
- 1 November 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (11) , 116103
Numerical study on wave configuration of wedge-induced oblique detonation wave: Reactive boundary layer effect
A numerical simulation solving the Reynolds-averaged Navier–Stokes equation is presented to investigate the initiation and evolution of the wedge-induced oblique detonation wave (ODW) with emphasis on the effects of the burning boundary layer. The nondimensional activation energy (Ea) is selected as the bifurcate parameter, which varies from 30 to 50. The largest induction ignition length behind the oblique shock/detonation wave is shown to be proportional to the Ea. The initiation of ODW can be attributed to the collision and diffraction of reactive waves. The wave configuration, a series of compression waves (or shock wave), is observed at the conjunction point of the burning boundary layer and combustion wave, which intensifies the pressure jump as increasing the Ea. The polar line analysis demonstrates that the pressure jump triggers the transition from regular reflection to Mach reflection near triple-point. The oscillations of the ODW wave structures, for example, the triple-point and Mach stem, can be attributed to the Rayleigh–Taylor instabilities developed on the reaction front of the boundary layer, which shall be appropriately suppressed to remain the steadiness of the ODW and flow configuration.
- Open Access
Lagrange Optimization of Shock Waves for Two-Dimensional Hypersonic Inlet with Geometric Constraints
The present paper focuses on the Lagrange optimization of shock waves for a two-dimensional hypersonic inlet by limiting the cowl internal angle and inlet length. The results indicate the significant influences of geometric constraints on the configuration of shock waves and performances of an inlet. Specifically, the cowl internal angle mainly affects the internal compression section; the inlet length affects both the internal and external compression sections where the intensity of internal and external compression shock waves shows a deviation of equal. In addition, the performances of optimized inlets at off-design points are further numerically simulated. A prominent discovery is that a longer inlet favors a higher total pressure recovery at the positive AOA; conversely, a shorter inlet can increase the total pressure recovery at the negative AOA.
Open AccessLagrange Optimization of Shock Waves for Two-Dimensional Hypersonic Inlet with Geometric Constraints
The present paper focuses on the Lagrange optimization of shock waves for a two-dimensional hypersonic inlet by limiting the cowl internal angle and inlet length. The results indicate the significant influences of geometric constraints on the configuration of shock waves and performances of an inlet. Specifically, the cowl internal angle mainly affects the internal compression section; the inlet length affects both the internal and external compression sections where the intensity of internal and external compression shock waves shows a deviation of equal. In addition, the performances of optimized inlets at off-design points are further numerically simulated. A prominent discovery is that a longer inlet favors a higher total pressure recovery at the positive AOA; conversely, a shorter inlet can increase the total pressure recovery at the negative AOA.