Luchuan Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Luchuan Ding has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Xiaodi Dai
Key Laboratory of Advanced Civil Engineering Materials of Ministry of Education, School of Materials Science and Engineering, Tongji University, Shanghai 201804, China
5 shared publications - Robby Caspeele
Ghent University
4 shared publications Zhengwu Jiang
4 shared publicationsGeert De Schutter
3 shared publications- Jianbing Chen
Tongji Univ
3 shared publications Qiang Ren
3 shared publications
Latest Publications
- Open Access
- 14 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (18) , 9112
Investigation into the Preparation Process and Properties of High-Ferrite Cement-Composite Cementitious Materials
In this study, ordinary Portland cement (OPC) clinker, high-ferrite cement (HFC) clinker, desulfurization gypsum, and limestone powder were utilized as raw materials. The effects of two processes, separate grinding followed by blending and co-grinding, on the particle size distribution, water requirement for normal consistency, and setting time of the OPC-HFC composite cementitious system were compared. On this basis, a strengthening agent was introduced to systematically investigate the rheological properties, early hydration heat evolution, and mortar strength development of the co-ground cementitious system. The results indicate that compared to separate grinding, the co-grinding process exploits the difference in the grindability of the two clinkers to produce a “self-widening” effect, thereby effectively optimizing the particle size distribution of the composite system. Among the three compositions examined, the co-ground CG2 system exhibited the lowest water requirement for normal consistency and relatively low yield stress, particularly at low w/b ratios. Furthermore, a relationship can be observed between the time-dependent rheological behavior of the paste and the staged characteristics of the early-age hydration heat evolution. The addition of the strengthening agent improved the 28 d compressive strength of the co-ground cementitious systems. These findings provide laboratory-scale experimental evidence regarding the performance feasibility of OPC–HFC composite cementitious materials and a reference for further composition and process optimization.
- 14 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (18) , 9112
Open AccessInvestigation into the Preparation Process and Properties of High-Ferrite Cement-Composite Cementitious Materials
In this study, ordinary Portland cement (OPC) clinker, high-ferrite cement (HFC) clinker, desulfurization gypsum, and limestone powder were utilized as raw materials. The effects of two processes, separate grinding followed by blending and co-grinding, on the particle size distribution, water requirement for normal consistency, and setting time of the OPC-HFC composite cementitious system were compared. On this basis, a strengthening agent was introduced to systematically investigate the rheological properties, early hydration heat evolution, and mortar strength development of the co-ground cementitious system. The results indicate that compared to separate grinding, the co-grinding process exploits the difference in the grindability of the two clinkers to produce a “self-widening” effect, thereby effectively optimizing the particle size distribution of the composite system. Among the three compositions examined, the co-ground CG2 system exhibited the lowest water requirement for normal consistency and relatively low yield stress, particularly at low w/b ratios. Furthermore, a relationship can be observed between the time-dependent rheological behavior of the paste and the staged characteristics of the early-age hydration heat evolution. The addition of the strengthening agent improved the 28 d compressive strength of the co-ground cementitious systems. These findings provide laboratory-scale experimental evidence regarding the performance feasibility of OPC–HFC composite cementitious materials and a reference for further composition and process optimization.
- 25 June 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 537
Understanding the effect of CO2 injection on cement hydration: A study on mass-transfer process modelling
- 25 June 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 537
Understanding the effect of CO2 injection on cement hydration: A study on mass-transfer process modelling
- Open Access
Axial Compressive Behavior of Square Double-Skin Hybrid Concrete Bar Columns with Small-Diameter Concrete-Infilled GFRP Tubes
With the increasing demand for lightweight, high-strength, and ductile structural systems in modern infrastructure, the hybrid composite column has emerged as a promising solution to overcome the limitations of single-material members. This paper proposes an innovative variant of double-skin tubular columns (DSTCs), termed as square double-skin hybrid concrete bar columns (SDHCBCs), composed of one square-shaped outer steel tube, small-diameter concrete-infilled glass FRP tubes (SDCFs), interstitial mortar, and an inner circular steel tube. A series of axial compression tests were conducted on eight SDHCBCs and one reference DSTC to investigate the effects of key parameters, including the thicknesses of the outer steel tube and GFRP tube, the substitution ratio of SDCFs, and their distribution patterns. As a result, significantly enhanced performance is observed in the proposed SDHCBCs, including the following: ultimate axial bearing capacity improved by 79.6%, while the ductility is increased by 328.3%, respectively, compared to the conventional DSTC. A validated finite element model was established to simulate the mechanical behavior of SDHCBCs under axial compression. The model accurately captured the stress distribution and progressive failure modes of each component, offering insights into the complex interaction mechanisms within the hybrid columns. The findings suggest that incorporating SDCFs into hybrid columns is a promising strategy to achieve superior load-carrying performance, with strong potential for application in high-rise and infrastructure engineering.
Open AccessAxial Compressive Behavior of Square Double-Skin Hybrid Concrete Bar Columns with Small-Diameter Concrete-Infilled GFRP Tubes
With the increasing demand for lightweight, high-strength, and ductile structural systems in modern infrastructure, the hybrid composite column has emerged as a promising solution to overcome the limitations of single-material members. This paper proposes an innovative variant of double-skin tubular columns (DSTCs), termed as square double-skin hybrid concrete bar columns (SDHCBCs), composed of one square-shaped outer steel tube, small-diameter concrete-infilled glass FRP tubes (SDCFs), interstitial mortar, and an inner circular steel tube. A series of axial compression tests were conducted on eight SDHCBCs and one reference DSTC to investigate the effects of key parameters, including the thicknesses of the outer steel tube and GFRP tube, the substitution ratio of SDCFs, and their distribution patterns. As a result, significantly enhanced performance is observed in the proposed SDHCBCs, including the following: ultimate axial bearing capacity improved by 79.6%, while the ductility is increased by 328.3%, respectively, compared to the conventional DSTC. A validated finite element model was established to simulate the mechanical behavior of SDHCBCs under axial compression. The model accurately captured the stress distribution and progressive failure modes of each component, offering insights into the complex interaction mechanisms within the hybrid columns. The findings suggest that incorporating SDCFs into hybrid columns is a promising strategy to achieve superior load-carrying performance, with strong potential for application in high-rise and infrastructure engineering.
- 6 October 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 114
Effects of simulated reinforcement corrosion on the static and dynamic progressive collapse behavior of RC subassemblies
- 6 October 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 114
Effects of simulated reinforcement corrosion on the static and dynamic progressive collapse behavior of RC subassemblies
- 22 September 2025
- Published by Elsevier in Engineering Structures
- Vol. 344
A unified regression model for the force-based dynamic increase factor in relation to progressive collapse analyses of frame structures
- 22 September 2025
- Published by Elsevier in Engineering Structures
- Vol. 344
A unified regression model for the force-based dynamic increase factor in relation to progressive collapse analyses of frame structures
- Open Access
Impact of Reinforcement Corrosion on Progressive Collapse Behavior of Multi-Story RC Frames
The progressive collapse performance of reinforced concrete (RC) building structures has been extensively investigated using the alternate load path method. However, most studies have focused on newly designed structures, with limited attention given to existing buildings. Since progressive collapse can occur at any point during a structure’s service life and at various locations within the structural system, this study examines the progressive collapse behavior of deteriorated RC frames subjected to simulated reinforcement corrosion. This paper presents an investigation into the system-level progressive collapse responses of deteriorated RC frames, which extends the current state of the art in this field. The influence of different material deteriorations, different corrosion locations, different column removal scenarios, and dynamic effects on structural response is explored. According to the results obtained in this research, a significant reduction in progressive collapse resistance can be resulted in with increasing corrosion levels. Notably, only reinforcement corrosion in the beams located directly above the removed column (i.e., within the directly affected part) for the investigated RC frame had a substantial impact on structural performance. In contrast, corrosion in other regions and concrete deterioration exhibited minimal influence in this work. An increased number of corroded floors further reduced collapse resistance. Dynamic progressive collapse resistance was found to be considerably lower than its static counterpart and decreased at a slightly faster rate as corrosion progressed. Additionally, the energy-based method was shown to provide a reasonable approximation of the maximum dynamic responses at different corrosion levels, offering a computationally efficient alternative to full dynamic analysis.
Open AccessImpact of Reinforcement Corrosion on Progressive Collapse Behavior of Multi-Story RC Frames
The progressive collapse performance of reinforced concrete (RC) building structures has been extensively investigated using the alternate load path method. However, most studies have focused on newly designed structures, with limited attention given to existing buildings. Since progressive collapse can occur at any point during a structure’s service life and at various locations within the structural system, this study examines the progressive collapse behavior of deteriorated RC frames subjected to simulated reinforcement corrosion. This paper presents an investigation into the system-level progressive collapse responses of deteriorated RC frames, which extends the current state of the art in this field. The influence of different material deteriorations, different corrosion locations, different column removal scenarios, and dynamic effects on structural response is explored. According to the results obtained in this research, a significant reduction in progressive collapse resistance can be resulted in with increasing corrosion levels. Notably, only reinforcement corrosion in the beams located directly above the removed column (i.e., within the directly affected part) for the investigated RC frame had a substantial impact on structural performance. In contrast, corrosion in other regions and concrete deterioration exhibited minimal influence in this work. An increased number of corroded floors further reduced collapse resistance. Dynamic progressive collapse resistance was found to be considerably lower than its static counterpart and decreased at a slightly faster rate as corrosion progressed. Additionally, the energy-based method was shown to provide a reasonable approximation of the maximum dynamic responses at different corrosion levels, offering a computationally efficient alternative to full dynamic analysis.
- 15 August 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 444
Development of 3D printable alkali-activated slag-metakaolin concrete
- 15 August 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 444
Development of 3D printable alkali-activated slag-metakaolin concrete