AJAgnieszka Jachura

Agnieszka Jachura

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Agnieszka Jachura has a total of 2 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Wpływ wykorzystania odnawialnych źródeł energii na środowisko na przykładzie lokalnego studium przypadku

    by Agnieszka Jachura

    W artykule zaprezentowano wyniki oceny ekologicznej trzech wariantów wykorzystujących odnawialne źródła energii (OZE) w budynku jednorodzinnym. W celu oceny wpływu produkcji ciepła i energii elektrycznej na środowisko, określono ilość emitowanych do powietrza głównych substancji zanieczyszczających. Aby móc porównać różne źródła energii oraz ocenić całkowity wpływ na środowisko, wyznaczono emisję równoważną oraz redukcję emisji zanieczyszczeń. Uzyskano najmniejsze obciążenie na środowisko w wariancie OZE3, który wykazał najwyższą redukcję dla wszystkich badanych zanieczyszczeń. Największe rozbieżności redukcji emisji zanieczyszczeń, w poszczególnych wariantach, uzyskano dla dwutlenku węgla (CO2) i tlenków azotu (NOX). Benzo-(a)-piren (B-a-P) wykazywał najwyższą toksycznością z pośród wszystkich badanych zanieczyszczeń. Zredukowanie jego emisji o ponad 99% znacząco wpłynie na zdrowie ludzkie. Uzyskana w wariancie OZE1 najniższa efektywność w redukcji emisji NOX oraz CO2, sugeruje ograniczoną skuteczność technologii zastosowanych w tym rozwiązaniu. Wykazano, że wszystkie warianty OZE znacząco poprawiają jakość powietrza, szczególnie w odniesieniu do pyłu, sadzy, B-a-P, dwutlenku siarki i tlenku węgla. Ich redukcja przekracza lub jest zbliżona do poziomu 90%.

  • Open Access

    Life Cycle Assessment of Dispersed Phase Change Material Heat Accumulators for Cooperation with Buildings in the District Heating System

    by Michał Turski, Agnieszka Jachura

    The wide use of energy-efficient district heating systems allows for decreased atmospheric pollution resulting from lower emissions. One of the ways to increase the efficiency of existing district heating systems, and a key element of new systems using renewable energy sources, is modern heat storage technology—the utilization of dispersed PCM heat accumulators. However, the use of different solutions and the inconsistency of selection methods make it difficult to compare the obtained results. Therefore, in this paper, using TRNSYS software, a standardization of the selection of dispersed PCM heat accumulators for cooperation with buildings in the DHS was proposed along with a Life Cycle Assessment. Life Cycle Assessment could be a good, versatile indicator for new developments in district heating systems. A new contribution to the research topic was the Life Cycle Assessment itself as well as the range of heat output of the substations up to 2000 kW and the development of nomograms and unitary values for the selection of individual parameters based on the relative amount of heat uncollected by buildings. The technical potential of heat storage value, %ΔQi,st, was from 49.4% to 59.6% of the theoretical potential of heat storage. The increases in the active volume of the PCM heat accumulator, dVPCM, and the mass of the required amount of PCM, dmst, were, respectively, 0.8 × 10−2–4.0 m3/kW and 1.3–6.7 × 10−2 kg/kW. Due to dispersed heat storage, an increase in system efficiency of 41% was achieved. LCA analysis showed that a positive impact on the environment was achieved, expressed as negative values of the Eco-indicator from −0.504 × 10−2 to −6.44 × 10−2 kPt/kW.


  • Open Access

    Life Cycle Assessment of the Use of Phase Change Material in an Evacuated Solar Tube Collector

    by Agnieszka Jachura, Robert Sekret

    This paper presents an environmental impact assessment of the entire cycle of existence of the tube-vacuum solar collector prototype. The innovativeness of the solution involved using a phase change material as a heat-storing material, which was placed inside the collector’s tubes-vacuum. The PCM used in this study was paraffin. The system boundaries contained three phases: production, operation (use phase), and disposal. An ecological life cycle assessment was carried out using the SimaPro software. To compare the environmental impact of heat storage, the amount of heat generated for 15 years, starting from the beginning of a solar installation for preparing domestic hot water for a single-family residential building, was considered the functional unit. Assuming comparable production methods for individual elements of the ETC and waste management scenarios, the reduction in harmful effects on the environment by introducing a PCM that stores heat inside the ETC ranges from 17 to 24%. The performed analyses have also shown that the method itself of manufacturing the materials used for the construction of the solar collector and the choice of the scenario of the disposal of waste during decommissioning the solar collector all play an important role in its environmental assessment. With an increase in the application of the advanced technologies of materials manufacturing and an increase in the amount of waste subjected to recycling, the degree of the solar collector’s environmental impact decreased by 82% compared to its standard manufacture and disposal.