Yuanquan Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yuanquan Yang has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
Runqing Liu
School of Materials Science and Engineering, Shenyang Ligong University, Shenyang, China
4 shared publicationsBaomin Wang
Institute of Building Materials, Faculty of Infrastructure Engineering, Dalian University of Technology, Dalian, 116024, China
3 shared publicationsBo Pang
School of Materials Science and Engineering, Shenyang Ligong University, Shenyang, China
3 shared publications- Bo Pang
School of Civil Engineering, Liuzhou Institute of Technology, Liuzhou 545616, China
3 shared publications Jun Liu
School of Materials Science and Engineering, Shenyang Ligong University 1 , Nanping Rd. No. 6, New Hunnan District, Shenyang 110168
3 shared publications- Runqing Liu
School of Materials Science and Engineering, Shenyang Ligong University, Shenyang 110159, China
3 shared publications
Latest Publications
- Open Access
Retarding Effect and Hydration Mechanism of Sodium Polyacrylate on Magnesium Potassium Phosphate Cement
Magnesium phosphate cement (MPC) is a type of rapid-hardening inorganic cementitious material, which has important application value in rapid road repair, solidification of hazardous and radioactive waste, and other fields. However, it suffers from excessively fast setting and hardening and a short working time retention, which severely restrict its engineering application. Therefore, the development of high-efficiency set retarders is of great significance for optimizing MPC performance, enhancing its construction workability, and expanding its application scope. In this study, the effect of sodium polyacrylate (PAAS) on the setting and hardening of magnesium potassium phosphate cement (MKPC) was investigated by testing the setting time and fluidity at a low water-to-solid ratio (W/S = 0.18). Through pH and electrical conductivity measurements, combined with XRD, TG/DTG, and FTIR characterizations, we elucidated the retarding mechanism of PAAS on MKPC using a high water-to-solid ratio (W/S = 10). The results indicate that the setting time of MKPC is positively correlated with the PAAS dosage, whereas the fluidity and compressive strength exhibited a negative correlation with the PAAS dosage. Additionally, PAAS reduces the total heat release and the heat release rate of MKPC. The addition of PAAS increased the pH of the suspension, thereby reducing the solubility of MgO, but did not inhibit the dissolution of KH2PO4. The carboxylate groups in PAAS chemically reacted with Mg2+ on the surface of MgO to form magnesium carboxylate complexes (Mg-PAA), which remained as precipitates in the MKPC suspension system, thus reducing the amount of available Mg2+ participating in the hydration reaction. Furthermore, PAAS had no effect on the final precipitate composition at the end of hydration, which was composed of MgKPO4·6H2O and Mg3(PO4)2·22H2O in all cases.
Open AccessRetarding Effect and Hydration Mechanism of Sodium Polyacrylate on Magnesium Potassium Phosphate Cement
Magnesium phosphate cement (MPC) is a type of rapid-hardening inorganic cementitious material, which has important application value in rapid road repair, solidification of hazardous and radioactive waste, and other fields. However, it suffers from excessively fast setting and hardening and a short working time retention, which severely restrict its engineering application. Therefore, the development of high-efficiency set retarders is of great significance for optimizing MPC performance, enhancing its construction workability, and expanding its application scope. In this study, the effect of sodium polyacrylate (PAAS) on the setting and hardening of magnesium potassium phosphate cement (MKPC) was investigated by testing the setting time and fluidity at a low water-to-solid ratio (W/S = 0.18). Through pH and electrical conductivity measurements, combined with XRD, TG/DTG, and FTIR characterizations, we elucidated the retarding mechanism of PAAS on MKPC using a high water-to-solid ratio (W/S = 10). The results indicate that the setting time of MKPC is positively correlated with the PAAS dosage, whereas the fluidity and compressive strength exhibited a negative correlation with the PAAS dosage. Additionally, PAAS reduces the total heat release and the heat release rate of MKPC. The addition of PAAS increased the pH of the suspension, thereby reducing the solubility of MgO, but did not inhibit the dissolution of KH2PO4. The carboxylate groups in PAAS chemically reacted with Mg2+ on the surface of MgO to form magnesium carboxylate complexes (Mg-PAA), which remained as precipitates in the MKPC suspension system, thus reducing the amount of available Mg2+ participating in the hydration reaction. Furthermore, PAAS had no effect on the final precipitate composition at the end of hydration, which was composed of MgKPO4·6H2O and Mg3(PO4)2·22H2O in all cases.
- 15 December 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (36) , 2281
Preparation and wave-absorbing properties of Ni0.5Zn0.5Fe2O4—fumed silica absorbers
- 15 December 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (36) , 2281
Preparation and wave-absorbing properties of Ni0.5Zn0.5Fe2O4—fumed silica absorbers
- Open Access
Performance Evolution and Degradation Mechanism of Chemically Bonded Phosphate Ceramic Cement Under Freeze–Thaw Cycles
This study investigates the performance variations in chemically bonded phosphate ceramic (CBPC) cement under different media (water and 3% NaCl solution) environments subjected to varying numbers of freeze–thaw cycles, including changes in compressive strength, mass loss rate, phase composition, microstructure, external pH, and ion concentration, with the aim of elucidating its long-term durability degradation mechanisms and microstructural evolution. The results show that both the mass and compressive strength of CBPC cement first increase and then decrease with increasing freeze–thaw cycles. After 400 cycles, the compressive strength decreases by 29.91% in water and 25.16% in salt solution. The pH value rises with cycling, along with increased concentrations of K+, Mg2+, and PO43−, while Na+ and Cl− concentrations decrease in salt solution. XRD/Rietveld analysis reveals that the content of MgKPO4·6H2O decreases from 28.1% to 19.5% (water) and 20.7% (salt), with a gradual reduction in crystallinity. TG/DTG and FTIR results confirm these findings, showing extensive microcracking in hydration products, which aligns with the observed macro-performance changes.
Open AccessPerformance Evolution and Degradation Mechanism of Chemically Bonded Phosphate Ceramic Cement Under Freeze–Thaw Cycles
This study investigates the performance variations in chemically bonded phosphate ceramic (CBPC) cement under different media (water and 3% NaCl solution) environments subjected to varying numbers of freeze–thaw cycles, including changes in compressive strength, mass loss rate, phase composition, microstructure, external pH, and ion concentration, with the aim of elucidating its long-term durability degradation mechanisms and microstructural evolution. The results show that both the mass and compressive strength of CBPC cement first increase and then decrease with increasing freeze–thaw cycles. After 400 cycles, the compressive strength decreases by 29.91% in water and 25.16% in salt solution. The pH value rises with cycling, along with increased concentrations of K+, Mg2+, and PO43−, while Na+ and Cl− concentrations decrease in salt solution. XRD/Rietveld analysis reveals that the content of MgKPO4·6H2O decreases from 28.1% to 19.5% (water) and 20.7% (salt), with a gradual reduction in crystallinity. TG/DTG and FTIR results confirm these findings, showing extensive microcracking in hydration products, which aligns with the observed macro-performance changes.
- Open Access
The Effect of Different Particle Sizes of Fly Ash on the Properties of Mortar
Fly ash is a commonly used mineral addition in construction engineering. Research on its different particle size distributions can help optimize material performance, promote resource utilization, and support environmental protection. In this study, the particle size of fly ash was used as a variable; fly ash with a single particle size was prepared by means of sieving, and the particle size was precisely controlled as a variable, thus avoiding the errors caused by the addition of multiple different particle sizes. Replacing 10% of the cement with fly ash to prepare cement mortar, the influence of fly ash particle size on the performance of cement mortar was investigated. The results show that the mortar incorporating fly ash with a particle size range of 10–20 μm achieves a 28-day compressive strength of 58.25 MPa and a flexural strength of 10.29 MPa. The hydration heat release rate of fly ash in the 10–20 μm range reaches a maximum of 1.84 mW/g, and the total hydration heat release peaks at 211.17 J/g at 70 h. The influence of fly ash particle size on the total hydration heat release is relatively small in the early stages but increases rapidly with prolonged hydration time. When the fly ash particle size is in the 10–20 μm range, the cement mortar exhibits the lowest total porosity at 12.88%, with the smallest average pore size of 27.1 nm and the smallest most probable pore size of 21.2 nm. This reduces harmful pores, increases the number of harmless pores, makes the cement mortar structure denser, and improves the durability of the mortar. The types of hydration products of different particle sizes of fly ash did not change. The smaller the particle size of fly ash, the more complete the volcanic ash reaction, promoting the hydration of mortar.
Open AccessThe Effect of Different Particle Sizes of Fly Ash on the Properties of Mortar
Fly ash is a commonly used mineral addition in construction engineering. Research on its different particle size distributions can help optimize material performance, promote resource utilization, and support environmental protection. In this study, the particle size of fly ash was used as a variable; fly ash with a single particle size was prepared by means of sieving, and the particle size was precisely controlled as a variable, thus avoiding the errors caused by the addition of multiple different particle sizes. Replacing 10% of the cement with fly ash to prepare cement mortar, the influence of fly ash particle size on the performance of cement mortar was investigated. The results show that the mortar incorporating fly ash with a particle size range of 10–20 μm achieves a 28-day compressive strength of 58.25 MPa and a flexural strength of 10.29 MPa. The hydration heat release rate of fly ash in the 10–20 μm range reaches a maximum of 1.84 mW/g, and the total hydration heat release peaks at 211.17 J/g at 70 h. The influence of fly ash particle size on the total hydration heat release is relatively small in the early stages but increases rapidly with prolonged hydration time. When the fly ash particle size is in the 10–20 μm range, the cement mortar exhibits the lowest total porosity at 12.88%, with the smallest average pore size of 27.1 nm and the smallest most probable pore size of 21.2 nm. This reduces harmful pores, increases the number of harmless pores, makes the cement mortar structure denser, and improves the durability of the mortar. The types of hydration products of different particle sizes of fly ash did not change. The smaller the particle size of fly ash, the more complete the volcanic ash reaction, promoting the hydration of mortar.
- 11 September 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (26) , 1-14
Design and microwave absorption properties of cement-based composites with CoCrFeO₄–carbon fiber hybrid absorbers
- 11 September 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (26) , 1-14
Design and microwave absorption properties of cement-based composites with CoCrFeO₄–carbon fiber hybrid absorbers
- 13 November 2024
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 35 (32) , 1-15
An investigation on preparation and wave-absorbing properties of carbon nanotube/ferrite/polyaniline complexes
- 13 November 2024
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 35 (32) , 1-15
An investigation on preparation and wave-absorbing properties of carbon nanotube/ferrite/polyaniline complexes
- 22 October 2024
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 52 (6) , 3408-3417
Dynamic Mechanical Properties of PVA Fiber-Reinforced Concrete after Freeze-Thaw Cycles
Concrete structures have been employed in a multitude of low- and even ultra–low-temperature environments, necessitating that these structures exhibit a certain degree of impact and explosion resistance in addition to the capacity to withstand the elevated temperatures induced by the low-temperature environment and the additional load. In this study, the dynamic mechanical properties of polyvinyl alcohol (PVA) fiber-reinforced concrete were investigated under freeze-thaw cycles at temperatures ranging from 20°C to −70°C. The research employed a split-Hopkinson pressure bar with a diameter of 75 mm. The findings revealed that the PVA fibers were randomly dispersed within the concrete matrix, exhibiting a superior bridging effect, effectively supporting the tensile stress generated by the impact. The impact toughness of concrete exhibited a biphasic response to the addition of PVA fiber admixture. Initially, the toughness increased with increasing fiber content, reaching a peak at 1.2 kg/m3. Subsequently, the toughness decreased with further increases in fiber content. The incorporation of PVA fibers significantly enhanced the energy absorption capacity of the concrete at freeze-thaw cycles between 20°C and −70°C.
- 22 October 2024
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 52 (6) , 3408-3417
Dynamic Mechanical Properties of PVA Fiber-Reinforced Concrete after Freeze-Thaw Cycles
Concrete structures have been employed in a multitude of low- and even ultra–low-temperature environments, necessitating that these structures exhibit a certain degree of impact and explosion resistance in addition to the capacity to withstand the elevated temperatures induced by the low-temperature environment and the additional load. In this study, the dynamic mechanical properties of polyvinyl alcohol (PVA) fiber-reinforced concrete were investigated under freeze-thaw cycles at temperatures ranging from 20°C to −70°C. The research employed a split-Hopkinson pressure bar with a diameter of 75 mm. The findings revealed that the PVA fibers were randomly dispersed within the concrete matrix, exhibiting a superior bridging effect, effectively supporting the tensile stress generated by the impact. The impact toughness of concrete exhibited a biphasic response to the addition of PVA fiber admixture. Initially, the toughness increased with increasing fiber content, reaching a peak at 1.2 kg/m3. Subsequently, the toughness decreased with further increases in fiber content. The incorporation of PVA fibers significantly enhanced the energy absorption capacity of the concrete at freeze-thaw cycles between 20°C and −70°C.
- 22 February 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 21 (3) , 1735-1746
Hydration properties of magnesium phosphate cement paste mixed with metakaolin and silica fume
Magnesium phosphate cement (MPC) exhibits a faster setting time and higher early strength, making it suitable for crack repair. However, its application in civil engineering is hindered by its fast initial hydration rate and poor water resistance. To address these limitations, metakaolin (MK) and silica fume (SF) were utilized to enhance the properties of MPC. The effects of MK and SF on the setting time, compressive strength, water resistance, hydration process, and microstructure of MPC were investigated. The results demonstrate that both MK and SF significantly prolong the setting time of MPC and improve its water resistance. The main hydration products of MPC, after incorporating MK and SF, are k‐struvite (MgKPO 4 ·6H 2 O) and unreacted MgO. The presence of MgSiO 3 and AlPO 4 also contributes to the enhancement of compressive strength and water resistance. The incorporation of MK and SF actively participates in the hydration reaction of the MPC system. Furthermore, MgSiO 3 and AlPO 4 intertwine with MKP, resulting in a denser internal structure of the cured MPC, thereby improving its water resistance.
- 22 February 2024
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 21 (3) , 1735-1746
Hydration properties of magnesium phosphate cement paste mixed with metakaolin and silica fume
Magnesium phosphate cement (MPC) exhibits a faster setting time and higher early strength, making it suitable for crack repair. However, its application in civil engineering is hindered by its fast initial hydration rate and poor water resistance. To address these limitations, metakaolin (MK) and silica fume (SF) were utilized to enhance the properties of MPC. The effects of MK and SF on the setting time, compressive strength, water resistance, hydration process, and microstructure of MPC were investigated. The results demonstrate that both MK and SF significantly prolong the setting time of MPC and improve its water resistance. The main hydration products of MPC, after incorporating MK and SF, are k‐struvite (MgKPO 4 ·6H 2 O) and unreacted MgO. The presence of MgSiO 3 and AlPO 4 also contributes to the enhancement of compressive strength and water resistance. The incorporation of MK and SF actively participates in the hydration reaction of the MPC system. Furthermore, MgSiO 3 and AlPO 4 intertwine with MKP, resulting in a denser internal structure of the cured MPC, thereby improving its water resistance.