Seung-Chang Han
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Seung-Chang Han has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Tea-Sung Jun
Department of Mechanical Engineering, Incheon National University, Incheon 22012, Republic of Korea
9 shared publications - Umer Masood Chaudry
Department of Mechanical Engineering, Incheon National University, Incheon, South Korea
3 shared publications Hafiz Muhammad Rehan Tariq
2 shared publications- Robert Maaß
Federal Institute of Materials Research and Testing (BAM), Berlin, Germany
2 shared publications Umer Masood Chaudry
2 shared publicationsAmeeq Farooq
1 shared publication
Latest Publications
- Open Access
- 6 August 2026
- Published by Springer Nature in npj Materials Degradation
- Vol. 10 (1)
Solid-state intermetallic grain-boundary precipitation as an early stage of liquid-metal embrittlement in advanced high-strength steels
Liquid-metal embrittlement (LME) in Zn-coated steels is traditionally understood as a consequence of liquid Zn penetration along grain boundaries (GBs) during thermo-mechanical processing. However, recent thermodynamic predictions brought to light a massive Zn segregation transition at Fe GBs that suggest a strong driving force for intermetallic phase formation at substantially lower temperatures than the melting point of Zn. Leveraging bulk mechanical testing, high-energy synchrotron diffraction, and transmission electron microscopy, we demonstrate here that embrittling Fe-rich intermetallic grain-boundary phases emerge in an advanced high-strength steel prior to any melting of Zn. Their formation and increasing presence with temperature correlates with severe mechanical degradation. These findings provide consistent evidence that the solid-state formation of Fe-rich Fe-Zn intermetallic phases constitutes an early contributing step to LME in galvanized high-strength steels.
- 6 August 2026
- Published by Springer Nature in npj Materials Degradation
- Vol. 10 (1)
Open AccessSolid-state intermetallic grain-boundary precipitation as an early stage of liquid-metal embrittlement in advanced high-strength steels
Liquid-metal embrittlement (LME) in Zn-coated steels is traditionally understood as a consequence of liquid Zn penetration along grain boundaries (GBs) during thermo-mechanical processing. However, recent thermodynamic predictions brought to light a massive Zn segregation transition at Fe GBs that suggest a strong driving force for intermetallic phase formation at substantially lower temperatures than the melting point of Zn. Leveraging bulk mechanical testing, high-energy synchrotron diffraction, and transmission electron microscopy, we demonstrate here that embrittling Fe-rich intermetallic grain-boundary phases emerge in an advanced high-strength steel prior to any melting of Zn. Their formation and increasing presence with temperature correlates with severe mechanical degradation. These findings provide consistent evidence that the solid-state formation of Fe-rich Fe-Zn intermetallic phases constitutes an early contributing step to LME in galvanized high-strength steels.
- Open Access
- 21 May 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 9549-9555
Impact of cyclic cryogenic treatment on the hardening behavior of pre-strained CoCrFeMnNi alloy
- 21 May 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 9549-9555
Open AccessImpact of cyclic cryogenic treatment on the hardening behavior of pre-strained CoCrFeMnNi alloy
- Open Access
- 14 May 2025
- Published by Elsevier in Scripta Materialia
- Vol. 265
On the preference of liquid-metal embrittlement along high-angle grain-boundaries in galvanized steels
- 14 May 2025
- Published by Elsevier in Scripta Materialia
- Vol. 265
Open AccessOn the preference of liquid-metal embrittlement along high-angle grain-boundaries in galvanized steels
- Open Access
- 16 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 1188-1200
Unraveling the anisotropic corrosion behavior along the building direction in laser powder bed fusion processed Hastelloy X
- 16 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 1188-1200
Open AccessUnraveling the anisotropic corrosion behavior along the building direction in laser powder bed fusion processed Hastelloy X
- Open Access
- 8 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 32, 4444-4455
Revealing the microstructural evolution and mechanical response of repaired Fe–Cr–Si based alloy by directed energy deposition
- 8 September 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 32, 4444-4455
Open AccessRevealing the microstructural evolution and mechanical response of repaired Fe–Cr–Si based alloy by directed energy deposition
- Open Access
- 1 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 29, 5118-5125
Achieving synergistic improvement of wear and mechanical properties in Ti–6Al–4V alloy by multiple cryogenic treatment
- 1 March 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 29, 5118-5125
Open AccessAchieving synergistic improvement of wear and mechanical properties in Ti–6Al–4V alloy by multiple cryogenic treatment
- Open Access
Effects of Paint Baking Heat Treatments on Mechanical Properties and Microstructure of Resistance Spot-Welded A5022-O and A6014-T4 Alloys
This study presents information on the behavior of paint baking (PB) after resistance spot welding of the 5- and 6xxx series aluminum alloys. The weld parameters are optimized, and the weld specimens are baked three times for 20 min at 180 °C to simulate the heat treatments required for paint baking. The mechanical properties of the samples were characterized by using the lap shear test, micro/nanoindentation hardness, and fatigue test. As the mechanical properties of the weld are affected by the characteristics of the heat-affected zone and those of the fusion zone, the microstructure of the cross-sections was also analyzed through optical and electron microscopy. The investigation of the 6xxx series welds showed that the post-processing heat treatment decreased both the strength and the toughness of the weld, which resulted from the reduced hardness of the microstructure. Additionally, the lap shear test indicated that the failure mode for the 6xxx series changed from nugget failure to partial nugget failure after the paint baking process. However, the mechanical properties of the 5xxx welds were not affected as much as the 6xxx series during baking heat treatment. The fatigue test for the 6xxx series showed a different tendency from the lap shear test. Its fatigue properties improved due to an increased elastic modulus after the heat treatment.
Open AccessEffects of Paint Baking Heat Treatments on Mechanical Properties and Microstructure of Resistance Spot-Welded A5022-O and A6014-T4 Alloys
This study presents information on the behavior of paint baking (PB) after resistance spot welding of the 5- and 6xxx series aluminum alloys. The weld parameters are optimized, and the weld specimens are baked three times for 20 min at 180 °C to simulate the heat treatments required for paint baking. The mechanical properties of the samples were characterized by using the lap shear test, micro/nanoindentation hardness, and fatigue test. As the mechanical properties of the weld are affected by the characteristics of the heat-affected zone and those of the fusion zone, the microstructure of the cross-sections was also analyzed through optical and electron microscopy. The investigation of the 6xxx series welds showed that the post-processing heat treatment decreased both the strength and the toughness of the weld, which resulted from the reduced hardness of the microstructure. Additionally, the lap shear test indicated that the failure mode for the 6xxx series changed from nugget failure to partial nugget failure after the paint baking process. However, the mechanical properties of the 5xxx welds were not affected as much as the 6xxx series during baking heat treatment. The fatigue test for the 6xxx series showed a different tendency from the lap shear test. Its fatigue properties improved due to an increased elastic modulus after the heat treatment.
- 11 July 2023
- Published by Elsevier in Materials Letters
- Vol. 349
Mitigating HAZ softening of friction stir welded ferrite-martensite DP steel followed by post weld heat treatment
- 11 July 2023
- Published by Elsevier in Materials Letters
- Vol. 349
Mitigating HAZ softening of friction stir welded ferrite-martensite DP steel followed by post weld heat treatment
- Open Access
Effect of Heat Treatment on Corrosion and Mechanical Properties of M789 Alloy Fabricated Using DED
The directed energy deposition (DED) process offers potential advantages, such as a large building space, limited dilutions, narrow heat-affected zones (HAZ) and potentially improved surface properties. Moreover, heat treatments have been reported to significantly improve the properties of the as-built sample by modifying the microstructure. In this study, the influences of various combinations of heating and cryogenic treatments on the mechanical performance and corrosion resistance of DED M789 steel have been critically investigated. The microstructure and hardness were examined to discuss the characteristics of the M789 parts in the as-printed and heat-treated states. The corrosion rate was determined from the weight loss monitoring based on the seawater immersion condition. The microstructural results revealed the distortion of martensite lattice and the formation of nano-carbide precipitates after the cryogenic treatment. Moreover, the microhardness of the cryogenically treated M789 steel was found to be significantly higher which was attributed to the precipitate strengthening and elimination of retained austenite, resulting from the increased volume fraction of carbides due to cryogenic treatment. The corrosion characteristics were also modified by the heating/cryogenic treatments, and the substrate-to-deposit ratio of the corrosion sample also substantially affected the overall corrosion rate.
Open AccessEffect of Heat Treatment on Corrosion and Mechanical Properties of M789 Alloy Fabricated Using DED
The directed energy deposition (DED) process offers potential advantages, such as a large building space, limited dilutions, narrow heat-affected zones (HAZ) and potentially improved surface properties. Moreover, heat treatments have been reported to significantly improve the properties of the as-built sample by modifying the microstructure. In this study, the influences of various combinations of heating and cryogenic treatments on the mechanical performance and corrosion resistance of DED M789 steel have been critically investigated. The microstructure and hardness were examined to discuss the characteristics of the M789 parts in the as-printed and heat-treated states. The corrosion rate was determined from the weight loss monitoring based on the seawater immersion condition. The microstructural results revealed the distortion of martensite lattice and the formation of nano-carbide precipitates after the cryogenic treatment. Moreover, the microhardness of the cryogenically treated M789 steel was found to be significantly higher which was attributed to the precipitate strengthening and elimination of retained austenite, resulting from the increased volume fraction of carbides due to cryogenic treatment. The corrosion characteristics were also modified by the heating/cryogenic treatments, and the substrate-to-deposit ratio of the corrosion sample also substantially affected the overall corrosion rate.
- Open Access
- 23 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 4976-4989
Effect of welding speed on the microstructure and texture development in the individual weld zone of friction stir welded DP780 steel
- 23 February 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 23, 4976-4989
Open AccessEffect of welding speed on the microstructure and texture development in the individual weld zone of friction stir welded DP780 steel