Nazanin Hosseini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nazanin Hosseini has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Fathallah Karimzadeh
Department of Materials Engineering, Isfahan University of Technology, Isfahan, Iran
5 shared publications M.H. Abbasi
4 shared publications- Mohammad Hossein Enayati
Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111, Iran
4 shared publications Chan-Gyung Park
1 shared publicationG.M. Choi
1 shared publicationJong Kee
1 shared publication
Latest Publications
- 1 November 2016
- Published by Elsevier in Applied Surface Science
- Vol. 385, 122-129
Wafer level package of Au-Ge system using a Ge chemical vapor deposition (CVD) thin film
- 1 November 2016
- Published by Elsevier in Applied Surface Science
- Vol. 385, 122-129
Wafer level package of Au-Ge system using a Ge chemical vapor deposition (CVD) thin film
- 1 September 2014
- Published by Elsevier in Ceramics International
- Vol. 40 (8) , 12219-12226
Microstructural characterization and electrical conductivity of Cu Mn3−O4 (0.9≤x≤1.3) spinels produced by optimized glycine–nitrate combustion and mechanical milling processes
- 1 September 2014
- Published by Elsevier in Ceramics International
- Vol. 40 (8) , 12219-12226
Microstructural characterization and electrical conductivity of Cu Mn3−O4 (0.9≤x≤1.3) spinels produced by optimized glycine–nitrate combustion and mechanical milling processes
- 1 October 2012
- Published by Elsevier in Tribology International
- Vol. 54, 58-67
A comparative study on the wear properties of coarse-grained Al6061 alloy and nanostructured Al6061–Al2O3 composites
- 1 October 2012
- Published by Elsevier in Tribology International
- Vol. 54, 58-67
A comparative study on the wear properties of coarse-grained Al6061 alloy and nanostructured Al6061–Al2O3 composites
- 20 January 2011
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 25 (02) , 265-275
FABRICATION AND CHARACTERIZATION OF NANOSTRUCTURED Al6061 ALLOY AND ITS AGING BEHAVIOR
The present paper is focused on fabrication, characterization, and aging behavior of nanostructured Al 6061 alloy prepared by mechanical milling. The milling was performed on Al 6061 in a planetary ball mill under argon atmosphere for various times up to 30 h. Isothermal heat treatment was then carried out on 30 h milled powder at different temperatures up to 550°C. The structural evolution of milled and annealed powders was studied by X-ray diffraction, SEM observation, and hardness measurements. The results showed that the final milled product was an Al – Mg – Si supersaturated solid solution having a grain size of 35 nm and a microhardness of 157 HV. Additionally, Mg 2 Si precipitation between 250 and 300°C led to an increase in hardness with the peak-aging hardness value of 207 HV after heat treatment at 300°C for 2 h. Above this temperature, due to the dissolution of the precipitates and grain growth, the hardness values decreased to 130 HV after heat treatment at 550°C for 3 h.
- 20 January 2011
- Published by World Scientific Pub Co Pte Ltd in International Journal of Modern Physics B
- Vol. 25 (02) , 265-275
FABRICATION AND CHARACTERIZATION OF NANOSTRUCTURED Al6061 ALLOY AND ITS AGING BEHAVIOR
The present paper is focused on fabrication, characterization, and aging behavior of nanostructured Al 6061 alloy prepared by mechanical milling. The milling was performed on Al 6061 in a planetary ball mill under argon atmosphere for various times up to 30 h. Isothermal heat treatment was then carried out on 30 h milled powder at different temperatures up to 550°C. The structural evolution of milled and annealed powders was studied by X-ray diffraction, SEM observation, and hardness measurements. The results showed that the final milled product was an Al – Mg – Si supersaturated solid solution having a grain size of 35 nm and a microhardness of 157 HV. Additionally, Mg 2 Si precipitation between 250 and 300°C led to an increase in hardness with the peak-aging hardness value of 207 HV after heat treatment at 300°C for 2 h. Above this temperature, due to the dissolution of the precipitates and grain growth, the hardness values decreased to 130 HV after heat treatment at 550°C for 3 h.
- 1 December 2010
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 31 (10) , 4777-4785
Tribological properties of Al6061–Al2O3 nanocomposite prepared by milling and hot pressing
- 1 December 2010
- Published by Elsevier in Materials & Design (1980-2015)
- Vol. 31 (10) , 4777-4785
Tribological properties of Al6061–Al2O3 nanocomposite prepared by milling and hot pressing
- 15 November 2009
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 525 (1-2) , 107-111
Structural evolution and grain growth kinetics during isothermal heat treatment of nanostructured Al6061
- 15 November 2009
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 525 (1-2) , 107-111
Structural evolution and grain growth kinetics during isothermal heat treatment of nanostructured Al6061