Meihong Zhang
Meihong Zhang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Huiwen Xu
Shanghai Aircraft Design and Research Institute
1 shared publication - Kun Mao
Shanghai Aircraft Design and Research Institute
1 shared publication - Kun Mao
Harbin Institute of Technology, Harbin 150006, China
1 shared publication - Pan Cheng
Shanghai Aircraft Design and Research Institute, Shanghai 200232, China
1 shared publication - Shengyang Nie
School of Civil Engineering and Architecture, Xi’an University of Technology, Xi’an 710048, China
1 shared publication - Wenkui Wang
Shanghai Aircraft Design and Research Institute
1 shared publication
Latest Publications
- 14 October 2025
- Published by Springer Nature
- p. 31-42
Aerodynamic Design and Experimental Validation of Ailerons Downward Deflection in the Takeoff Configuration of a Civil Aircraft
- 14 October 2025
- Published by Springer Nature
- p. 31-42
Aerodynamic Design and Experimental Validation of Ailerons Downward Deflection in the Takeoff Configuration of a Civil Aircraft
- Open Access
A Modification to the Enhanced Correction Factor Technique for the Subsonic Wing–Body Interference Model
In this work, the enhanced correction factor technique (ECFT) is modified for a subsonic wing–body interference model, which can consider the forces on both the lifting boxes and the body elements of an idealized airplane, termed the advanced ECFT method. A passenger aircraft model is chosen as the simulation model, and the longitudinal static aeroelasticity at the transonic situation for two-degree freedom, including the α (angle of attack) degree and ϕ (angle of horizontal tail) degree, is simulated in this paper. The corresponding CFD results are used to correct the aerodynamic influence coefficients (AIC) matrix, which is then simulated by MSC.NASTRAN. The pressure distribution results of different aircraft components received by the advanced ECFT method indicate that it is suitable for the subsonic wing–body interference model. Compared with the uncorrected linear method and the diagonal corrected method, it is generally more consistent with the CFD/CSD coupling method, not only for the lifting boxes, but also for the body elements. In addition, the aerodynamic derivative results also show good agreement with the flight test data, which solidly verifies the advance ECFT method.
Open AccessA Modification to the Enhanced Correction Factor Technique for the Subsonic Wing–Body Interference Model
In this work, the enhanced correction factor technique (ECFT) is modified for a subsonic wing–body interference model, which can consider the forces on both the lifting boxes and the body elements of an idealized airplane, termed the advanced ECFT method. A passenger aircraft model is chosen as the simulation model, and the longitudinal static aeroelasticity at the transonic situation for two-degree freedom, including the α (angle of attack) degree and ϕ (angle of horizontal tail) degree, is simulated in this paper. The corresponding CFD results are used to correct the aerodynamic influence coefficients (AIC) matrix, which is then simulated by MSC.NASTRAN. The pressure distribution results of different aircraft components received by the advanced ECFT method indicate that it is suitable for the subsonic wing–body interference model. Compared with the uncorrected linear method and the diagonal corrected method, it is generally more consistent with the CFD/CSD coupling method, not only for the lifting boxes, but also for the body elements. In addition, the aerodynamic derivative results also show good agreement with the flight test data, which solidly verifies the advance ECFT method.
- Open Access
The Application of the γ-Reθt Transition Model Using Sustaining Turbulence
The freestream turbulence intensity is an important parameter for Tollmien–Schlichting waves and is also used as one of the key variables for the local- and transport-equation-based transition model in the simulations. To obtain the similar turbulence level in the vicinity to the aircraft as the turbulence intensity measured in a wind tunnel or in free-flight conditions, the sustaining turbulence term can be used for the transition model. It is important to investigate the model behavior when the sustaining turbulence is coupled with the frequently used SST-variants for transitional flows. Additionally, it is essential to obtain a nearly independent solution using the same transition model for different users on different meshes with similar grid resolution for purposes of verification and validation. So far, the relevant work has not been performed sufficiently and the sustaining turbulence technology introduces non-independent results into the freestream values. Thus, a modified sustaining turbulence approach is adopted and investigated in several test cases, including a computational effort on NACA0021 test case at 10 angles of attack. The results indicate that the modified sustaining turbulence in conjunction with the SST-2003 turbulence model yields results nearly independent to the freestream value of ω for the prediction of both streamwise and crossflow transition for two-dimensional flows without increasing computational effort too much. For three-dimensional flow, the sensitivity to initial value of ω is reduced significantly as well in comparison to the SST-based transition model, and it is highly recommended to use present sustaining turbulence technology in conjunction with the SST-2003-based transition model for engineering applications.
Open AccessThe Application of the γ-Reθt Transition Model Using Sustaining Turbulence
The freestream turbulence intensity is an important parameter for Tollmien–Schlichting waves and is also used as one of the key variables for the local- and transport-equation-based transition model in the simulations. To obtain the similar turbulence level in the vicinity to the aircraft as the turbulence intensity measured in a wind tunnel or in free-flight conditions, the sustaining turbulence term can be used for the transition model. It is important to investigate the model behavior when the sustaining turbulence is coupled with the frequently used SST-variants for transitional flows. Additionally, it is essential to obtain a nearly independent solution using the same transition model for different users on different meshes with similar grid resolution for purposes of verification and validation. So far, the relevant work has not been performed sufficiently and the sustaining turbulence technology introduces non-independent results into the freestream values. Thus, a modified sustaining turbulence approach is adopted and investigated in several test cases, including a computational effort on NACA0021 test case at 10 angles of attack. The results indicate that the modified sustaining turbulence in conjunction with the SST-2003 turbulence model yields results nearly independent to the freestream value of ω for the prediction of both streamwise and crossflow transition for two-dimensional flows without increasing computational effort too much. For three-dimensional flow, the sensitivity to initial value of ω is reduced significantly as well in comparison to the SST-based transition model, and it is highly recommended to use present sustaining turbulence technology in conjunction with the SST-2003-based transition model for engineering applications.