Bing Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bing Zhou has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Baoping Gong
Southwestern Institute of Physics, Chengdu 610041, China
4 shared publications Long Zhang
Southwestern Institute of Physics, Chengdu, China
4 shared publicationsXiaoyu Wang
Southwestern Institute of Physics, Chengdu, China
4 shared publicationsYanling Wang
Southwestern Institute of Physics, Chengdu, China
3 shared publicationsBo Hu
2 shared publicationsDeqi Chen
2 shared publications
Latest Publications
- 30 December 2025
- Published by Elsevier in Fusion Engineering and Design
- Vol. 224
Experimental study on particle crushing and pressure drop characteristics of Li4SiO4 breeder pebble beds
- 30 December 2025
- Published by Elsevier in Fusion Engineering and Design
- Vol. 224
Experimental study on particle crushing and pressure drop characteristics of Li4SiO4 breeder pebble beds
- 15 August 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 207
Experimental study on the pressure drop of helium purge gas in particle crushing pebble beds
- 15 August 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 207
Experimental study on the pressure drop of helium purge gas in particle crushing pebble beds
- Open Access
Holistic Hydraulic Simulation for Pebble Bed Using Porous Media Approach
The porous media approach is regarded as an appropriate methodology for hydraulic simulations of complex pebble beds in fusion reactors. In order to determine the parameters (permeability α and inertial loss coefficient C) of the porous media accurately, two methods are proposed: the correction method and the fitting method. In this paper, a single-channel model with sequentially packed pebbles is constructed in order to obtain the pressure drop gradient against superficial velocities. Two methods, the correction method and fitting method, are employed to determine the permeability and inertial loss coefficient, and the results are evaluated with comparisons. Based on the results, both the correction method and fitting method are deemed feasible for the parameter determinations. In consideration of the consumption of resources and time for simulation, the fitting method is recommended during the preliminary design phase to shorten the duration of design, while the correction method is suggested to obtain precise results when the design is accomplished. Both of the methods would be evaluated with the data obtained from experiments in the future.
Open AccessHolistic Hydraulic Simulation for Pebble Bed Using Porous Media Approach
The porous media approach is regarded as an appropriate methodology for hydraulic simulations of complex pebble beds in fusion reactors. In order to determine the parameters (permeability α and inertial loss coefficient C) of the porous media accurately, two methods are proposed: the correction method and the fitting method. In this paper, a single-channel model with sequentially packed pebbles is constructed in order to obtain the pressure drop gradient against superficial velocities. Two methods, the correction method and fitting method, are employed to determine the permeability and inertial loss coefficient, and the results are evaluated with comparisons. Based on the results, both the correction method and fitting method are deemed feasible for the parameter determinations. In consideration of the consumption of resources and time for simulation, the fitting method is recommended during the preliminary design phase to shorten the duration of design, while the correction method is suggested to obtain precise results when the design is accomplished. Both of the methods would be evaluated with the data obtained from experiments in the future.
- Open Access
- 8 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (6) , 2289
Investigation of Wall Effect on Packing Structures and Purge Gas Flow Characteristics in Pebble Beds for Fusion Blanket by Combining Discrete Element Method and Computational Fluid Dynamics Simulation
In a tritium-breeding blanket of a fusion reaction, helium, used as a tritium-purging gas, will purge the tritium breeder pebble beds to extract the tritium in blanket. The purge gas flow characteristics will affect the tritium extraction efficiency. The effect of the fixed wall on the pebble packing structures and purge gas flow characteristics was investigated by combining the discrete element method (DEM) and computational fluid dynamics (CFD) method. The results indicate that the fixed wall leads to a regular packing of the pebbles adjacent to the fixed wall in association with drastic fluctuations in the porosity of the pebble bed, which can affect the purge gas flow behaviors. Further analyses of helium flow behaviors show that the helium pressure in the pebble bed decreases in a linear manner along the flow direction, whereas the pressure drop gradient of helium increases gradually with an increase in the packing factor. The reduction in porosity in the pebble bed leads to a notable escalation in helium flow velocity. Concerning the direction perpendicular to the helium gas flow, the evolution of the cut-plane averaged velocity of helium is similar to that of the porosity, except in the region immediately adjacent to the wall. The pressure drop and flow characteristics obtained in this study can serve as input for the thermohydraulic analysis of the tritium blowing systems in the tritium-breeding blanket of a fusion reactor.
- 8 March 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (6) , 2289
Open AccessInvestigation of Wall Effect on Packing Structures and Purge Gas Flow Characteristics in Pebble Beds for Fusion Blanket by Combining Discrete Element Method and Computational Fluid Dynamics Simulation
In a tritium-breeding blanket of a fusion reaction, helium, used as a tritium-purging gas, will purge the tritium breeder pebble beds to extract the tritium in blanket. The purge gas flow characteristics will affect the tritium extraction efficiency. The effect of the fixed wall on the pebble packing structures and purge gas flow characteristics was investigated by combining the discrete element method (DEM) and computational fluid dynamics (CFD) method. The results indicate that the fixed wall leads to a regular packing of the pebbles adjacent to the fixed wall in association with drastic fluctuations in the porosity of the pebble bed, which can affect the purge gas flow behaviors. Further analyses of helium flow behaviors show that the helium pressure in the pebble bed decreases in a linear manner along the flow direction, whereas the pressure drop gradient of helium increases gradually with an increase in the packing factor. The reduction in porosity in the pebble bed leads to a notable escalation in helium flow velocity. Concerning the direction perpendicular to the helium gas flow, the evolution of the cut-plane averaged velocity of helium is similar to that of the porosity, except in the region immediately adjacent to the wall. The pressure drop and flow characteristics obtained in this study can serve as input for the thermohydraulic analysis of the tritium blowing systems in the tritium-breeding blanket of a fusion reactor.
- Open Access
Experimental Investigation on Pressure Drops of Purge Gas Helium in Packed Pebble Beds for Nuclear Fusion Blanket
The flow characteristics of purge gas helium in the pebble bed of the tritium breeding blanket are important in analyzing the tritium purging process and optimizing the design of the solid breeder blanket. Therefore, the flow characteristics of helium gas in randomly packed pebble beds are investigated experimentally with a focus on the analysis of the pressure loss distribution. The results show that gas velocity, bed dimension, and pebble diameters have an obvious influence on the helium flow characteristics in pebble beds. With the increase in the inlet helium gas velocity, the pressure drop gradient of helium in the pebble bed gradually increased. With increases in the pebble bed dimension, the pressure drop gradient of helium in the pebble bed gradually increased. With the increase in the pebble diameter, the pressure drop gradient gradually decreased. In addition, the effect of temperature on the pressure drop of helium in the pebble bed was also preliminarily investigated. The pressure drop gradient of the helium through the pebble bed obviously increased with the increase in the helium and the bed temperature. The experimentally obtained pressure loss characteristics can be used for the validation of the simulation of a blanket pebble bed and as input parameters in the thermo-hydraulic analysis of solid-tritium breeder blankets.
Open AccessExperimental Investigation on Pressure Drops of Purge Gas Helium in Packed Pebble Beds for Nuclear Fusion Blanket
The flow characteristics of purge gas helium in the pebble bed of the tritium breeding blanket are important in analyzing the tritium purging process and optimizing the design of the solid breeder blanket. Therefore, the flow characteristics of helium gas in randomly packed pebble beds are investigated experimentally with a focus on the analysis of the pressure loss distribution. The results show that gas velocity, bed dimension, and pebble diameters have an obvious influence on the helium flow characteristics in pebble beds. With the increase in the inlet helium gas velocity, the pressure drop gradient of helium in the pebble bed gradually increased. With increases in the pebble bed dimension, the pressure drop gradient of helium in the pebble bed gradually increased. With the increase in the pebble diameter, the pressure drop gradient gradually decreased. In addition, the effect of temperature on the pressure drop of helium in the pebble bed was also preliminarily investigated. The pressure drop gradient of the helium through the pebble bed obviously increased with the increase in the helium and the bed temperature. The experimentally obtained pressure loss characteristics can be used for the validation of the simulation of a blanket pebble bed and as input parameters in the thermo-hydraulic analysis of solid-tritium breeder blankets.
- 26 September 2023
- Published by Elsevier in Fusion Engineering and Design
- Vol. 196
Preliminary accident analyses of in-box LOCA for CFETR HCCB blanket system
- 26 September 2023
- Published by Elsevier in Fusion Engineering and Design
- Vol. 196
Preliminary accident analyses of in-box LOCA for CFETR HCCB blanket system
- 26 March 2022
- Published by Elsevier in Fusion Engineering and Design
- Vol. 178
Preliminary accident analyses of ex-vessel LOCA and TES pipe break for CFETR HCCB blanket system
- 26 March 2022
- Published by Elsevier in Fusion Engineering and Design
- Vol. 178
Preliminary accident analyses of ex-vessel LOCA and TES pipe break for CFETR HCCB blanket system
- 1 November 2021
- Published by Elsevier in Fusion Engineering and Design
- Vol. 172
Preliminary activation analysis and radioactive waste classification for CFETR
- 1 November 2021
- Published by Elsevier in Fusion Engineering and Design
- Vol. 172
Preliminary activation analysis and radioactive waste classification for CFETR
- 1 November 2021
- Published by Elsevier in Fusion Engineering and Design
- Vol. 172
Accident classification and initial events for CFETR
- 1 November 2021
- Published by Elsevier in Fusion Engineering and Design
- Vol. 172
Accident classification and initial events for CFETR