ASAna Cristina S. Serra

Ana Cristina S. Serra

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ana Cristina S. Serra has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Fuel Oil Production in Catalytic Pyrolysis of Polyolefins with a Chromium Pillared Clay

    by da Silva Serra, Ana Cristina, Jacyra Guimarães Faillace, da Costa Marques Calderari, Monica Regina

    HDPE, LDPE and PP are the most produced polyolefins today. As these polymers are mainly used in packaging, their life cycle is short, generating large amounts of post-consumer plastic waste. The purpose of this study was to evaluate the efficiency of chromium pillared clay (CrPILC) as catalyst in pyrolysis of virgin and post-consumer polyolefins (HDPE, LDPE and PP) to obtain fuel oil in diesel fraction rich in n-paraffins. CrPILC was synthesized from a commercial Brazilian clay and an acid-restructured clay (K10) was used for comparison. Assays were performed in a fixed-bed reactor at 450 °C for 15 min. Chemical composition of liquids from pyrolysis was analyzed by Gas Chromatography-Mass Spectrometry (GC–MS) and Gas Chromatography with Simulated Distillation (GC-SIMDIS). Catalytic pyrolysis of polyolefins with K10 generated higher proportions of pyrolytic liquid than CrPILC. The liquids from catalytic pyrolysis with HDPE presented a homologous series distribution of n-alkanes like diesel oil, mainly using CrPILC. Simulated distillation curves from pyrolysis of polyolefins with K10 produced higher contents of light hydrocarbons in diesel range (C 9 -C 24 ), (~ 80%) than CrPILC (~ 65%). The content of light hydrocarbons in diesel range increased with HDPE (35%), LDPE and PP (20%) in pyrolysis with K10 and 20% in pyrolysis of CrPILC only with HDPE, if compared to thermal cracking of the polyolefins. Cracking results suggest that K10 was more effective for cracking polyolefins, while CrPILC was more selective for cracking HDPE. The content of acid sites and mesopore properties from K10 probably favored the production of paraffinic compounds.


  • Reviewing the use of zeolites and clay based catalysts for pyrolysis of plastics and oil fractions

    by Ana C. S. Serra, Jonatas V. Milato, Jacyra G. Faillace, Monica R. C. M. Calderari


  • Open Access

    Laser flash photolysis study of the phenolic hydrogen abstraction by 1,2-aceanthrylenedione triplet

    by Ana Cristina S. Serra, Nanci C. de Lucas, José Carlos Netto-Ferreira

    The nanosecond laser flash photolysis technique has been used to study the reactivity of 1,2-aceanthrylenedione (1) triplet towards phenols. Using acetonitrile as solvent, the quenching rate constant k q ranged from 3.3 x 10(5) L mol-1s-1 (phenol) to 1.3 x 10(7) L mol-1s-1 (4hydroxyphenol). Phenols with electron donating substituents were more reactive. The kinetic isotope effect (kH/kD) observed for the quenching of 1 with 4-methoxyphenol was 1.5. The Hammett plot for the reaction of the triplet of 1 with phenols gave a reaction constant rho = 1.04 in acetonitrile solution. The low value for the quenching rate constant measured for this triplet with 1,3-cyclohexadiene (k q=2.0 x 10(4) L mol-1s-1) and the diffusion controlled quenching rate constant obtained for beta-carotene suggest that the energy of the lowest triplet state for 1,2-aceanthrylenedione is located between 88 and 219 kJ mol-1.