Ilmars Blumbergs
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ilmars Blumbergs has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Ashish Kumar Singh
Composite Materials and Mechanics Laboratory, Mechanical and Aerospace Engineering Department, New York University, Tandon School of Engineering, Brooklyn, USA
3 shared publications - Ints Steins
Faculty of Material Science and Applied Chemistry, Institute of Materials and Surface Engineering, Paula Valdena Street 3/7, Riga Technical University, Riga, LV-1048, Latvia
3 shared publications - Rafał Chatys
Kielce University of Technology, Al. Tysiąclecia Państwa Polskiego 7, 25-314 Kielce, Poland
3 shared publications - Reinis Drunka
Riga Technical University
3 shared publications - Aleksandr K. Arnautov
Institute of Polymer Mechanics
2 shared publications - Aya Medany
Riga Technical University/Aeronautics Institute, Transport Department
2 shared publications
Latest Publications
- Open Access
Flexural Strength Enhancement of Lightweight Concrete Beams Using Carbon Fiber and Epoxy Resin
The paper presents the effect of reinforcing aerated concrete and volcanic rock on flexural strength. The tests used a three-point flexural test on beams made of both materials and two types of reinforcement: an Epidian 5 epoxy resin coating and carbon fabric impregnated with the same resin. The carbon composite increased the strength of aerated concrete by 1940% and volcanic rock by 2633% compared to unreinforced samples. The resin alone improved the load-bearing capacity of the beams by aerated concrete 118% and volcanic rock 147%, respectively. The tests showed that the resin filled the pores of the porous materials, significantly increasing their flexural strength.
Open AccessFlexural Strength Enhancement of Lightweight Concrete Beams Using Carbon Fiber and Epoxy Resin
The paper presents the effect of reinforcing aerated concrete and volcanic rock on flexural strength. The tests used a three-point flexural test on beams made of both materials and two types of reinforcement: an Epidian 5 epoxy resin coating and carbon fabric impregnated with the same resin. The carbon composite increased the strength of aerated concrete by 1940% and volcanic rock by 2633% compared to unreinforced samples. The resin alone improved the load-bearing capacity of the beams by aerated concrete 118% and volcanic rock 147%, respectively. The tests showed that the resin filled the pores of the porous materials, significantly increasing their flexural strength.
- Open Access
- 24 October 2025
- Published by University of Applied Sciences in Tarnow, Poland in Science, Technology and Innovation
- Vol. 21 (2) , 37-44
Entropy-probabilistic model for controlling the human factor in the system of ensuring the airworthiness of aircraft and their components
The following issues are addressed in the paper: A mathematical model for controlling human factors in the aircraft maintenance system is proposed, aimed at identifying priority tasks in maintaining airworthiness under conditions of limited resources. The model is developed using factor analysis under uncertainty, employing the entropy ranking method. In this approach, non-conformances in the activities of technical personnel (violations and errors) are represented as a multidimensional random generalized factor that comprises several measurable specific factors. The task of the management system is to determine the entropy of the generalized factor based on these measurable components. A functional diagram of the control system is developed based on a systems approach, considering it as a dynamic system that, at each moment, is described by a set of physical variables (parameters). Based on statistical data on deviations in the activities of airline technical personnel collected over a 10-year period, entropy indicators were obtained for several logically grouped factors—generalized indicators characterizing the main areas of management activities related to the continuing airworthiness of aircraft. The results make it possible to identify the main areas of preventive activities within the airline aimed at reducing the negative impact of human factors during aircraft maintenance, which is particularly important under conditions of limited resources.
- 24 October 2025
- Published by University of Applied Sciences in Tarnow, Poland in Science, Technology and Innovation
- Vol. 21 (2) , 37-44
Open AccessEntropy-probabilistic model for controlling the human factor in the system of ensuring the airworthiness of aircraft and their components
The following issues are addressed in the paper: A mathematical model for controlling human factors in the aircraft maintenance system is proposed, aimed at identifying priority tasks in maintaining airworthiness under conditions of limited resources. The model is developed using factor analysis under uncertainty, employing the entropy ranking method. In this approach, non-conformances in the activities of technical personnel (violations and errors) are represented as a multidimensional random generalized factor that comprises several measurable specific factors. The task of the management system is to determine the entropy of the generalized factor based on these measurable components. A functional diagram of the control system is developed based on a systems approach, considering it as a dynamic system that, at each moment, is described by a set of physical variables (parameters). Based on statistical data on deviations in the activities of airline technical personnel collected over a 10-year period, entropy indicators were obtained for several logically grouped factors—generalized indicators characterizing the main areas of management activities related to the continuing airworthiness of aircraft. The results make it possible to identify the main areas of preventive activities within the airline aimed at reducing the negative impact of human factors during aircraft maintenance, which is particularly important under conditions of limited resources.
- Open Access
Analysis of Fatigue and Residual Strength Estimation of Polymer Matrix Composites Using the Theory of the Markov Chain Method
This paper deals with an important issue, which is the influence of failure caused by the quality of matrix post-curing on the strength of complex and difficult materials of the “new generation” such as fibre composites, particularly with a polymer matrix. In recent years, significant advances in the field of adhesive materials chemistry have led to the constant development of bonding technology. The effectiveness of bonding depends, to a large extent, on the suitable selection of the adhesive and the use of appropriate surface treatment technology. It is difficult to imagine virtually any modern industry without adhesive joints, be it the aircraft, aerospace or automotive industries, which simultaneously highlights the great importance of adhesives and adhesive materials for the present-day economy. In modern technology, it is extremely important to obtain the right combination of modern construction materials. The statistical analysis of the components showed the complexity of the layered composite structure. The proposed model of the weakest micro-volume developed in this study indirectly reflects the experimentally based curing variables that affect the stresses of the components in the composite (laminate) structure. The strength of fibrous composite structures based on the Markov chain theory considers technological aspects during hardening. The model proposed in the paper was validated on the basis of examples from the literature and experimental data obtained in the research project. The numerical results are in good agreement with the literature database and measurement data. The presented model could be a novel method, which allows better insight into the curing process of epoxy resins.
Open AccessAnalysis of Fatigue and Residual Strength Estimation of Polymer Matrix Composites Using the Theory of the Markov Chain Method
This paper deals with an important issue, which is the influence of failure caused by the quality of matrix post-curing on the strength of complex and difficult materials of the “new generation” such as fibre composites, particularly with a polymer matrix. In recent years, significant advances in the field of adhesive materials chemistry have led to the constant development of bonding technology. The effectiveness of bonding depends, to a large extent, on the suitable selection of the adhesive and the use of appropriate surface treatment technology. It is difficult to imagine virtually any modern industry without adhesive joints, be it the aircraft, aerospace or automotive industries, which simultaneously highlights the great importance of adhesives and adhesive materials for the present-day economy. In modern technology, it is extremely important to obtain the right combination of modern construction materials. The statistical analysis of the components showed the complexity of the layered composite structure. The proposed model of the weakest micro-volume developed in this study indirectly reflects the experimentally based curing variables that affect the stresses of the components in the composite (laminate) structure. The strength of fibrous composite structures based on the Markov chain theory considers technological aspects during hardening. The model proposed in the paper was validated on the basis of examples from the literature and experimental data obtained in the research project. The numerical results are in good agreement with the literature database and measurement data. The presented model could be a novel method, which allows better insight into the curing process of epoxy resins.
- Open Access
- 28 February 2025
- Published by Praise Worthy Prize in International Review of Aerospace Engineering (IREASE)
- Vol. 18 (1) , 1-7
Recovery Model for Aircraft at Airports Within the Airline Network of the Airline Company
Recovery Model for Aircraft at Airports Within the Airline Network of the Airline Company
- 28 February 2025
- Published by Praise Worthy Prize in International Review of Aerospace Engineering (IREASE)
- Vol. 18 (1) , 1-7
Open AccessRecovery Model for Aircraft at Airports Within the Airline Network of the Airline Company
Recovery Model for Aircraft at Airports Within the Airline Network of the Airline Company
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2989 (1)
Effect of chemical and phase composition of feedstock materials and sintering temperature on spark plasma sintered mullite ceramics
Spark plasma sintering (SPS) is a method to consolidate fine powders to produce ceramic parts. Due to thermal cycles and pressures applied during SPS, phase transformations occur in raw materials used for producing high performance ceramics. In this study alumina in two forms, a-and γ-Al2O3, and silica (SiO2) mixed with zirconia (ZrO2) were sintered to form zirconia-mullite (MMA and MMG, respectively). The properties of these ceramics were compared with those produced by sintering pre-synthesized mullite nano-powder with and without zirconia addition. The content of mullite formed was studied for specimens made with alumina and silica feedstocks. The raw materials were sintered at different temperatures to obtain the correct temperature for obtaining highest mullite content and high density. Phase composition, morphology and mechanical properties of the ceramics were studied. It was found that the mullite prepared at 1500 °C with γ-Al2O3 has a higher percentage of mullite phase. However, the specimen made with pre-synthesized mullite powder had the highest mechanical properties.
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2989 (1)
Open AccessEffect of chemical and phase composition of feedstock materials and sintering temperature on spark plasma sintered mullite ceramics
Spark plasma sintering (SPS) is a method to consolidate fine powders to produce ceramic parts. Due to thermal cycles and pressures applied during SPS, phase transformations occur in raw materials used for producing high performance ceramics. In this study alumina in two forms, a-and γ-Al2O3, and silica (SiO2) mixed with zirconia (ZrO2) were sintered to form zirconia-mullite (MMA and MMG, respectively). The properties of these ceramics were compared with those produced by sintering pre-synthesized mullite nano-powder with and without zirconia addition. The content of mullite formed was studied for specimens made with alumina and silica feedstocks. The raw materials were sintered at different temperatures to obtain the correct temperature for obtaining highest mullite content and high density. Phase composition, morphology and mechanical properties of the ceramics were studied. It was found that the mullite prepared at 1500 °C with γ-Al2O3 has a higher percentage of mullite phase. However, the specimen made with pre-synthesized mullite powder had the highest mechanical properties.
- Open Access
Combined PEO and Spray Pyrolysis Coatings of Phosphate and ZnO for Enhancing Corrosion Resistance in AZ31 Mg Alloy
Oxide films produced from plasma electrolytic oxidation are porous in structure. While they have some passivating effect in Mg alloys, the pores still lead to corrosion over long periods of exposure. In this study, spray pyrolysis was used to seal the porous oxide layer developed through the plasma electrolytic oxidation method on Mg alloy AZ31. The PEO coating acted as a good base for the application of spray pyrolysis due to its morphology. Three different kinds of coatings were obtained using different precursors: zinc acetate for ZnO, phosphoric acid for phosphate (P), and a mixture of zinc acetate and sodium phosphate for ZnO+P. The corrosion performance of all three coatings was studied by performing electrochemical impedance and polarization tests on the samples. Mass loss over a duration of 1 week was measured in 3% NaCl solution using immersion gravimetry. The coating with only phosphate (P) was found to be most corrosion-resistant with 52 times lower rate of corrosion and 50 times more polarization potential. The chemical composition of the corrosion products was studied using XRD and SEM-EDS analysis. Mass loss in ZnO+P was the highest, at up to 1.4 and 5.1 times higher than ZnO and P, respectively.
Open AccessCombined PEO and Spray Pyrolysis Coatings of Phosphate and ZnO for Enhancing Corrosion Resistance in AZ31 Mg Alloy
Oxide films produced from plasma electrolytic oxidation are porous in structure. While they have some passivating effect in Mg alloys, the pores still lead to corrosion over long periods of exposure. In this study, spray pyrolysis was used to seal the porous oxide layer developed through the plasma electrolytic oxidation method on Mg alloy AZ31. The PEO coating acted as a good base for the application of spray pyrolysis due to its morphology. Three different kinds of coatings were obtained using different precursors: zinc acetate for ZnO, phosphoric acid for phosphate (P), and a mixture of zinc acetate and sodium phosphate for ZnO+P. The corrosion performance of all three coatings was studied by performing electrochemical impedance and polarization tests on the samples. Mass loss over a duration of 1 week was measured in 3% NaCl solution using immersion gravimetry. The coating with only phosphate (P) was found to be most corrosion-resistant with 52 times lower rate of corrosion and 50 times more polarization potential. The chemical composition of the corrosion products was studied using XRD and SEM-EDS analysis. Mass loss in ZnO+P was the highest, at up to 1.4 and 5.1 times higher than ZnO and P, respectively.
- 20 July 2023
- Published by Springer Nature
- p. 441-452
Space Law: Current Situation and Development in Ukraine and Latvia
- 20 July 2023
- Published by Springer Nature
- p. 441-452
Space Law: Current Situation and Development in Ukraine and Latvia
- Open Access
Nanomechanical and Electrochemical Corrosion Testing of Nanocomposite Coating Obtained on AZ31 via Plasma Electrolytic Oxidation Containing TiN and SiC Nanoparticles
Lightweight magnesium alloys offer excellent benefits over Al alloys due to their high specific strength and damping properties, but they are more prone to galvanic corrosion. Plasma electrolytic oxidation (PEO) coatings reinforced by nanoparticles have been shown to improve corrosion resistance and possess better mechanical properties. A lot of research has been published that focuses on the effect of nanoparticle concentration in the PEO electrolyte solution, and the type of nanoparticle, on the properties obtained. The aim of paper is to study the effect of processing time on the nanoparticle-reinforced PEO coating on AZ31 magnesium alloy. TiN and SiC nanoparticles were produced using plasma chemical synthesis and added to KOH-based electrolyte to develop PEO coatings. The concentration of nanoparticles was kept constant at 0.5 g/L and the treatment time was varied as follows: 1, 2, 3, 5, and 10 min. The coatings were tested for their microstructure, phase, chemical makeup, nano-mechanical properties, and corrosion resistance. Nanoparticles were found to be clustered in the coating and spread unevenly but led to a decrease in the size and number of pores on the PEO coating surface. The corrosion resistance and nano-mechanical properties of the coating improved with treatment time. The hardness and contact modulus of coatings with TiN particles were 26.7 and 25.2% greater than those with SiC particles. Addition of TiN nanoparticles resulted in improved corrosion resistance of the PEO coatings when the processing time was 5 or 10 min. The lowest corrosion rate of 6.3 × 10−5 mm/yr was obtained for TiN-added PEO coating processed for 10 min.
Open AccessNanomechanical and Electrochemical Corrosion Testing of Nanocomposite Coating Obtained on AZ31 via Plasma Electrolytic Oxidation Containing TiN and SiC Nanoparticles
Lightweight magnesium alloys offer excellent benefits over Al alloys due to their high specific strength and damping properties, but they are more prone to galvanic corrosion. Plasma electrolytic oxidation (PEO) coatings reinforced by nanoparticles have been shown to improve corrosion resistance and possess better mechanical properties. A lot of research has been published that focuses on the effect of nanoparticle concentration in the PEO electrolyte solution, and the type of nanoparticle, on the properties obtained. The aim of paper is to study the effect of processing time on the nanoparticle-reinforced PEO coating on AZ31 magnesium alloy. TiN and SiC nanoparticles were produced using plasma chemical synthesis and added to KOH-based electrolyte to develop PEO coatings. The concentration of nanoparticles was kept constant at 0.5 g/L and the treatment time was varied as follows: 1, 2, 3, 5, and 10 min. The coatings were tested for their microstructure, phase, chemical makeup, nano-mechanical properties, and corrosion resistance. Nanoparticles were found to be clustered in the coating and spread unevenly but led to a decrease in the size and number of pores on the PEO coating surface. The corrosion resistance and nano-mechanical properties of the coating improved with treatment time. The hardness and contact modulus of coatings with TiN particles were 26.7 and 25.2% greater than those with SiC particles. Addition of TiN nanoparticles resulted in improved corrosion resistance of the PEO coatings when the processing time was 5 or 10 min. The lowest corrosion rate of 6.3 × 10−5 mm/yr was obtained for TiN-added PEO coating processed for 10 min.
- 22 February 2023
- Published by Springer Nature
- p. 645-654
Analysis of International Air Hubs: A Competitiveness Review
- 22 February 2023
- Published by Springer Nature
- p. 645-654
Analysis of International Air Hubs: A Competitiveness Review
- Open Access
- 1 February 2023
- Published by Walter de Gruyter GmbH in Latvian Journal of Physics and Technical Sciences
- Vol. 60 (1) , 67-75
Methodological Approaches to the Design of a Mobile Test Facility Simulating the Outer Space
The article presents the results of the analysis of methodological approaches to the development of a mobile space simulator test facility following a low-budget project under the conditional name Metamorphosis. The project was performed at the Institute of Aeronautics of Riga Technical University together with Cryogenic and Vacuum Systems Ltd., a company specializing in the development and production of vacuum and cryogenic equipment, with extensive experience in creating technologies used in space research, and development and exploitation of the space environment simulation. The main aim of the study is to find an inexpensive outer space simulator test facility. The study shows that the liquid helium, hydrogen, and neon are significantly more expensive substances than liquid nitrogen, liquid carbon dioxide, liquid ammonia, and organic refrigerants (as well as equipment for their liquefaction). It is desirable to consider a nitrogen system for cooling the workspace due to the physical properties of nitrogen and cheap refrigerants for a projected low-cost simulator test facility. The description of the systems that should be included in the projected mobile space simulator is provided in the article. A generalized scheme of the simulator based on a cryogenic system is also presented.
- 1 February 2023
- Published by Walter de Gruyter GmbH in Latvian Journal of Physics and Technical Sciences
- Vol. 60 (1) , 67-75
Open AccessMethodological Approaches to the Design of a Mobile Test Facility Simulating the Outer Space
The article presents the results of the analysis of methodological approaches to the development of a mobile space simulator test facility following a low-budget project under the conditional name Metamorphosis. The project was performed at the Institute of Aeronautics of Riga Technical University together with Cryogenic and Vacuum Systems Ltd., a company specializing in the development and production of vacuum and cryogenic equipment, with extensive experience in creating technologies used in space research, and development and exploitation of the space environment simulation. The main aim of the study is to find an inexpensive outer space simulator test facility. The study shows that the liquid helium, hydrogen, and neon are significantly more expensive substances than liquid nitrogen, liquid carbon dioxide, liquid ammonia, and organic refrigerants (as well as equipment for their liquefaction). It is desirable to consider a nitrogen system for cooling the workspace due to the physical properties of nitrogen and cheap refrigerants for a projected low-cost simulator test facility. The description of the systems that should be included in the projected mobile space simulator is provided in the article. A generalized scheme of the simulator based on a cryogenic system is also presented.