Ichiro Ogura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ichiro Ogura has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Kiwamu Ashida
National Institute of Advanced Industrial Science and Technology (AIST)
4 shared publications - Hideo Kosaka
Yokohama National University
3 shared publications - Takahiro Numai
College of Science and Engineering, Ritsumeikan University, Kusatsu, Japan
3 shared publications - German Herrera-Granados
National Institute of Industrial Science and Technology (AIST), Tokyo, Japan
2 shared publications K. Kasahara
NEC Corporation, Ibaraki, Japan
2 shared publicationsK. Kurihara
NEC Corporation, Ibaraki, Japan
2 shared publications
Latest Publications
- Open Access
- 5 September 2025
- Published by Fuji Technology Press Ltd. in International Journal of Automation Technology
- Vol. 19 (5) , 801-810
Determination of Gear Skiving Tool Life Using an Image-Based Wear Detection System
Gear skiving is a high-precision cutting technology that is particularly well-suited for machining internal gears. It is essential to evaluate tool wear on the machine in a timely manner to accurately estimate tool life. Existing research focuses on the development of an evaluation system that estimates wear and breakage through image-based observation. This study outlines the system configuration and presents an image processing method for extracting tool geometry. However, the flank surface reflection interfered with the extraction of the rake face ridge during bottom-up observation, where a reflector was placed behind the tool. To resolve this, a new contour-extraction method was employed. This method involves installing a blue or other colored reflector, illuminating the adjacent surface with diffusely reflected light, capturing an image of the tool bottom illuminated with white light, and applying RGB color decomposition. An index value that comprehensively evaluates the difference between the tool profile before and after each machining operation is also proposed. Additionally, a corresponding procedure is established to identify tool wear or chipping by comparing the index value to a threshold value that is determined based on its relationship to the actual amount of wear. The experimental results demonstrate that the index value increases progressively with tool wear advancement, validating the effectiveness of the proposed method. However, owing to image focus, wear detection can become unreliable, making it a critical consideration in image-based wear detection methodologies.
- 5 September 2025
- Published by Fuji Technology Press Ltd. in International Journal of Automation Technology
- Vol. 19 (5) , 801-810
Open AccessDetermination of Gear Skiving Tool Life Using an Image-Based Wear Detection System
Gear skiving is a high-precision cutting technology that is particularly well-suited for machining internal gears. It is essential to evaluate tool wear on the machine in a timely manner to accurately estimate tool life. Existing research focuses on the development of an evaluation system that estimates wear and breakage through image-based observation. This study outlines the system configuration and presents an image processing method for extracting tool geometry. However, the flank surface reflection interfered with the extraction of the rake face ridge during bottom-up observation, where a reflector was placed behind the tool. To resolve this, a new contour-extraction method was employed. This method involves installing a blue or other colored reflector, illuminating the adjacent surface with diffusely reflected light, capturing an image of the tool bottom illuminated with white light, and applying RGB color decomposition. An index value that comprehensively evaluates the difference between the tool profile before and after each machining operation is also proposed. Additionally, a corresponding procedure is established to identify tool wear or chipping by comparing the index value to a threshold value that is determined based on its relationship to the actual amount of wear. The experimental results demonstrate that the index value increases progressively with tool wear advancement, validating the effectiveness of the proposed method. However, owing to image focus, wear detection can become unreliable, making it a critical consideration in image-based wear detection methodologies.
- 7 January 2025
- Published by Springer Nature
- p. 496-501
Monitoring System for Laser Welding and Emitting Energy Distribution Model to Explain Nonlinear Relationship
- 7 January 2025
- Published by Springer Nature
- p. 496-501
Monitoring System for Laser Welding and Emitting Energy Distribution Model to Explain Nonlinear Relationship
- 4 March 2024
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 112 (8) , 5811-5824
Mechanism of mechanical nanolithography using self-excitation microcantilever
- 4 March 2024
- Published by Springer Nature in Nonlinear Dynamics
- Vol. 112 (8) , 5811-5824
Mechanism of mechanical nanolithography using self-excitation microcantilever
- 1 April 2018
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 254, 248-253
Proposal of laser assisted hot embossing technology for glass
- 1 April 2018
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 254, 248-253
Proposal of laser assisted hot embossing technology for glass
- 1 January 2016
- Published by Elsevier in Precision Engineering
- Vol. 43, 544-553
Development of a non-rigid micro-scale cutting mechanism applying a normal cutting force control system
- 1 January 2016
- Published by Elsevier in Precision Engineering
- Vol. 43, 544-553
Development of a non-rigid micro-scale cutting mechanism applying a normal cutting force control system
- 1 November 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 523-524, 93-98
Micro-Groove Cutting for Different Materials Using an Elastic Leaf Spring Type Tool Holder
Micro-grooves fabrication is increasing due to its importance in different technology fields, as they are required for higher functional applications such as the development of optical lens or micro channels for heat exchangers. A novel method based on the technology developed for Atomic Force Microscopes (AFM) nano-cutting is proposed, where nano-scratches are made using a micro-cantilever with a sharp tip where a normal load sufficient to remove material is applied. Instead of a rigid system to control the relative position between the tool and the workpiece, AFM nano-cutting uses a force feedback control (FBC) of the normal load on the tool edge in order to maintain a constant cutting depth during the manufacture. Due to the limited scale range of AFM machining, a larger mechanism was developed and consists on a XYZ-stage system where an elastic leaf spring type tool holder is mounted with a diamond tool chip. FBC is not yet implemented on this system; however, basic experiments (micro-grooves cutting) were performed on different materials to verify the feasibility of this setup. With these results, it is possible to analyze the relationship between static indentation tests and the normal load required during the micro-grooves fabrication.
- 1 November 2012
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 523-524, 93-98
Micro-Groove Cutting for Different Materials Using an Elastic Leaf Spring Type Tool Holder
Micro-grooves fabrication is increasing due to its importance in different technology fields, as they are required for higher functional applications such as the development of optical lens or micro channels for heat exchangers. A novel method based on the technology developed for Atomic Force Microscopes (AFM) nano-cutting is proposed, where nano-scratches are made using a micro-cantilever with a sharp tip where a normal load sufficient to remove material is applied. Instead of a rigid system to control the relative position between the tool and the workpiece, AFM nano-cutting uses a force feedback control (FBC) of the normal load on the tool edge in order to maintain a constant cutting depth during the manufacture. Due to the limited scale range of AFM machining, a larger mechanism was developed and consists on a XYZ-stage system where an elastic leaf spring type tool holder is mounted with a diamond tool chip. FBC is not yet implemented on this system; however, basic experiments (micro-grooves cutting) were performed on different materials to verify the feasibility of this setup. With these results, it is possible to analyze the relationship between static indentation tests and the normal load required during the micro-grooves fabrication.
- 1 January 1993
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 32 (1S) , 604
Double-Mesa-Structure Vertical-to-Surface Transmission Electro-Photonic Device with a Vertical Cavity
We report a high electronic-optical power conversion efficiency of 11.4% in the laser operation of a double-mesa-structure vertical-to-surface transmission electro-photonic device with a vertical cavity. This high conversion efficiency is due to both reduction in the device resistance and increase in light emission efficiency. To reduce electrical resistance, a double mesa structure with a highly doped region is proposed and the resistance reduction is analyzed. To increase light emission efficiency, efficient carrier confinement in the active region by a proton-implanted structure, threshold current reduction by photon recycling, and decreased light absorption by annealing after proton implantation are utilized. Electronic-optical conversion efficiency of over 10% is achieved in surface-emitting devices for the first time to the authors' knowledge.
- 1 January 1993
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 32 (1S) , 604
Double-Mesa-Structure Vertical-to-Surface Transmission Electro-Photonic Device with a Vertical Cavity
We report a high electronic-optical power conversion efficiency of 11.4% in the laser operation of a double-mesa-structure vertical-to-surface transmission electro-photonic device with a vertical cavity. This high conversion efficiency is due to both reduction in the device resistance and increase in light emission efficiency. To reduce electrical resistance, a double mesa structure with a highly doped region is proposed and the resistance reduction is analyzed. To increase light emission efficiency, efficient carrier confinement in the active region by a proton-implanted structure, threshold current reduction by photon recycling, and decreased light absorption by annealing after proton implantation are utilized. Electronic-optical conversion efficiency of over 10% is achieved in surface-emitting devices for the first time to the authors' knowledge.
- 1 January 1992
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 24 (2) , S121-S132
Vertical-to-surface transmission electrophotonic device with a pnpn structure and vertical cavity
- 1 January 1992
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 24 (2) , S121-S132
Vertical-to-surface transmission electrophotonic device with a pnpn structure and vertical cavity