Ali Moshiri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ali Moshiri has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
A. Zarei-Hanzaki
9 shared publicationsH.R. Abedi
5 shared publications- Hamid Reza Abedi
School of Metallurgy & Materials Engineering, Iran University of Science and Technology (IUST), Tehran, Iran
5 shared publications - Javad Charkhchian
Hot Deformation and Thermomechanical Processing Laboratory of High‐Performance Engineering Materials School of Metallurgy and Materials Engineering College of Engineering University of Tehran Tehran 1439956191 Iran
3 shared publications B. Mirshekari
2 shared publications- Jiajia Shen
CENIMAT/I3N, Department of Materials Science, NOVA School of Science and Technology, Universidade NOVA de Lisboa, 2829-516 Caparica, Portugal
2 shared publications
Latest Publications
- 1 March 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (7)
Revealing the Effects of Friction Stir Processing on the Microstructural Evolutions and Mechanical Properties of As‐Cast Interstitial FeMnCoCrN High‐Entropy Alloy
The present study aims to investigate the effect of friction stir processing (FSP) on the microstructural evolutions and mechanical properties of a nonequiatomic interstitial high‐entropy alloy (HEA). To achieve this, an as‐cast FeMnCoCrN interstitial HEA undergoes FSP to modify the as‐cast microstructure and investigate the resulting effects on mechanical properties. The grain size, sub‐boundaries, martensite fraction, and accommodated strain exhibit a gradient from the base metal (BM) to the stir zone (SZ). As a result of FSP, the average grain size in the upper SZ is significantly decreased from ≈700 μm in BM to 1.5 μm, which is around 500 times finer than that of the BM. Furthermore, the martensitic transformation in a single metastable face‐centered‐cubic phase specifically occurs in the thermomechanical‐affected and heat‐affected zones. Continuous and geometric dynamic recrystallizations triggered by FSP lead to the development of a refined equiaxed microstructure. This gradient microstructure, in turn, plays a pivotal role in achieving significantly improved mechanical properties when compared to the as‐cast microstructure. Remarkably, the yield strength doubles, the ultimate tensile strength increases from 548 to 852 MPa, and ductility increases by 16%.
- 1 March 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (7)
Revealing the Effects of Friction Stir Processing on the Microstructural Evolutions and Mechanical Properties of As‐Cast Interstitial FeMnCoCrN High‐Entropy Alloy
The present study aims to investigate the effect of friction stir processing (FSP) on the microstructural evolutions and mechanical properties of a nonequiatomic interstitial high‐entropy alloy (HEA). To achieve this, an as‐cast FeMnCoCrN interstitial HEA undergoes FSP to modify the as‐cast microstructure and investigate the resulting effects on mechanical properties. The grain size, sub‐boundaries, martensite fraction, and accommodated strain exhibit a gradient from the base metal (BM) to the stir zone (SZ). As a result of FSP, the average grain size in the upper SZ is significantly decreased from ≈700 μm in BM to 1.5 μm, which is around 500 times finer than that of the BM. Furthermore, the martensitic transformation in a single metastable face‐centered‐cubic phase specifically occurs in the thermomechanical‐affected and heat‐affected zones. Continuous and geometric dynamic recrystallizations triggered by FSP lead to the development of a refined equiaxed microstructure. This gradient microstructure, in turn, plays a pivotal role in achieving significantly improved mechanical properties when compared to the as‐cast microstructure. Remarkably, the yield strength doubles, the ultimate tensile strength increases from 548 to 852 MPa, and ductility increases by 16%.
- Open Access
- 6 October 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 1908-1921
On the cyclic deformation behavior and correlated damage mechanism of selective laser melted AlSi10Mg alloy holding different initial microstructures
- 6 October 2023
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 27, 1908-1921
Open AccessOn the cyclic deformation behavior and correlated damage mechanism of selective laser melted AlSi10Mg alloy holding different initial microstructures
- Open Access
- 20 July 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 20, 551-560
On the short-time thermal phase-stability of as-cast AlCoCrFeNi2.1 eutectic high entropy alloy
- 20 July 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 20, 551-560
Open AccessOn the short-time thermal phase-stability of as-cast AlCoCrFeNi2.1 eutectic high entropy alloy
- Open Access
- 29 March 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 2428-2434
Effect of second phase particles on the microstructure and texture of rare earth elements containing magnesium matrix surface-composite produced by friction stir processing
- 29 March 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 18, 2428-2434
Open AccessEffect of second phase particles on the microstructure and texture of rare earth elements containing magnesium matrix surface-composite produced by friction stir processing
- Open Access
- 29 January 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 17, 1628-1641
Dynamic strain aging and twin formation during warm deformation of a novel medium-entropy lightweight steel
- 29 January 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 17, 1628-1641
Open AccessDynamic strain aging and twin formation during warm deformation of a novel medium-entropy lightweight steel
- 1 October 2020
- Published by Elsevier in International Journal of Fatigue
- Vol. 139
Stress-relaxation viewpoint to study the room-temperature cyclic deformation behavior of a low-density steel
- 1 October 2020
- Published by Elsevier in International Journal of Fatigue
- Vol. 139
Stress-relaxation viewpoint to study the room-temperature cyclic deformation behavior of a low-density steel
- 1 August 2020
- Published by Elsevier in Materials Characterization
- Vol. 166
Optimizing the austenite stability in a ferritic lightweight steel through thermomechanical processing
- 1 August 2020
- Published by Elsevier in Materials Characterization
- Vol. 166
Optimizing the austenite stability in a ferritic lightweight steel through thermomechanical processing