Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Zhenhai Pan has a total of 45 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Cavity evolution and cooling process during the water entry of a heated sphere

    by Hongxin Ye, Jialing Yu, Xuemei Chen, Haoxiang Huang, Zhenhai Pan

    In this paper, the water-entry process of high-temperature spheres was examined. Due to the intense phase change, the cavities formed by high-temperature spheres differed significantly from those formed by ambient-temperature spheres. Based on distinct cavity evolutionary characteristics, two cavity types were identified: quasi-static cavities occurring at lower initial impact velocities and deep seal cavities occurring at higher initial impact velocities. The variation trends of pinch-off time and characteristic length with respect to initial impact velocity differed among these cavity types due to their unique evolutionary behaviors. Further analysis revealed that although no significant differences in the motion of the sphere were observed among different cavity types, the initial impact velocity significantly influenced it. Higher initial impact velocities resulted in greater drag forces but lower drag coefficients. Next, higher initial impact velocities also induced higher phase change rates in the early stages of the sphere's water entry. Furthermore, the distinct cavity types led to differences in vapor distribution during the process. At the pinch-off time, the quasi-static cavities contained higher vapor content due to their smaller cavity volume. Finally, the cooling process of the sphere also varied with cavity type: for quasi-static cavities, heat flux gradually increased as the gas–liquid interface progressively enveloped the sphere, whereas for deep seal cavities, heat flux remained stable most of the time because the area of the sphere surface near the interface remained stable.


  • Transition of buoyancy-driven flow from an axisymmetric to non-axisymmetric vortex inside an evaporating sessile droplet

    by Jialing Yu, Zhenhai Pan, Justin A. Weibel

    The internal flow within an evaporating sessile droplet has intriguing fluid mechanics important to various microfluidics applications. In the present study, a phenomenon is observed through numerical methods wherein the buoyancy-driven flow structure inside a droplet on a non-wetting substrate transitions from an axisymmetric toroidal vortex flow to a non-axisymmetric single vortex flow with increase in the substrate temperature. As the axisymmetric nature of the droplet flow field and evaporation characteristics are broken, the internal velocity accelerates significantly. The transition, which is attributed to a flow instability inside the droplet, is more prone to occur as the droplet volume or the contact angle increases. The onset of the flow transition is analysed as the amplification of a small perturbation, thereby establishing a correlation between the flow instability and the Rayleigh number (Ra). Specifically, when Ra exceeds some critical value, the onset of the flow transition is observed, which explains the effects of substrate temperature and droplet volume on the internal flow. Next, the influence of the droplet contact angle on the critical Ra was investigated, and the underlying reasons were analysed. Finally, we discuss the heat transfer efficiency within the droplet and analyse why the internal flow tends to transition to a non-axisymmetric flow pattern from an energy minimization perspective.


  • Open Access

    Behind the Non-Uniform Breakup of Bubble Slug in Y-Shaped Microchannel: Dynamics and Mechanisms

    by Haoxiang Huang, Jiazheng Liu, Jialing Yu, Wentao Pan, Zhe Yan, Zhenhai Pan

    Bubble flow in confined geometries is a problem of fundamental and technological significance. Among all the forms, bubble breakup in bifurcated microchannels is one of the most commonly encountered scenarios, where an in-depth understanding is necessary for better leveraging the process. This study numerically investigates the non-uniform breakup of a bubble slug in Y-shaped microchannels under different flow ratios, Reynolds numbers, and initial bubble volumes. Overall, the bubble can either breakup or non-breakup when passing through the bifurcation and shows different forms depending on flow regimes. The flow ratio-Reynolds number phase diagrams indicate a power–law transition line of breakup and non-breakup. The bubble takes longer to break up with rising flow ratios yet breaks earlier with higher Reynolds numbers and volumes. Non-breakup takes less time than the breakup patterns. Flow ratio is the origin of non-uniform breakup. Both the Reynolds number and initial volume influence the bubble states when reaching the bifurcation and thus affect subsequent processes. Bubble neck dynamics are analyzed to describe the breakup further. The volume distribution after breaking up is found to have a quadratic relation with the flow ratio. Our study is hoped to provide insights for practical applications related to non-uniform bubble breakups.


  • Open Access

    Weakening of Ledinegg Instability and Maldistribution of Boiling Flow in Parallel Microchannels by Entry Effects

    by Jieyan Jiang, Changxu Chen, Haoxiang Huang, Zhenhai Pan

    In the pursuit of enhancing thermal management for miniaturized electronic devices, our study delves into the impact of entry effects on Ledinegg instability and flow maldistribution within parallel microchannels. Utilizing a coupled model that incorporates phase change and pressure drop dynamics in boiling flow, we examine microchannels characterized by a 50 length-to-diameter ratio and a 200 μm hydraulic diameter. Our findings unveil a significant influence of entry effects, which narrow the total flow excursion interval, thereby bolstering system stability. Specifically, as the heat flux escalates from 5 W/cm2 to 120 W/cm2, the entry effects increasingly mitigate flow instability and maldistribution in parallel channels, diminishing the total flow rate range susceptible to flow instability by 4.73% and 47.52%, while narrowing the total flow rate range corresponding to uneven flow distribution by 4.70% and 46.75%, respectively. Furthermore, entry effects expand the inlet subcooling range necessary for stabilizing the parallel channel system by 38.89% and 1000%. This research not only underscores the importance of considering entry effects in microchannel design but also opens avenues for further exploration into enhancing thermal management solutions.


  • On interaction between a bubble with evaporation and heated pillar block in microchannel

    by Haoxiang Huang, Jialing Yu, Zhe Yan, Zhenhai Pan

    As demand for managing high heat flux in specialized applications grows, flow boiling in microchannels has received escalating attention for its high efficiency and cost-effectiveness. The complex interaction between an evaporating bubble and a heated pillar in a microchannel is governed by a confluence of transport mechanisms, including bubble morphology, fluid convection, heat transfer, and phase change phenomena. This study develops a three-dimensional mathematical model, employing the saturated-interface-volume approach to simulate the complex interaction process effectively. The results indicate that the liquid film thickness between the bubble and the heated surface is the primary factor affecting heat transfer. A reduction in the Reynolds number as well as an increase in the initial bubble diameter lead to a decrease in the liquid film thickness and an increase in the temperature gradient within the thin liquid film, which enhance both the evaporation rate and heat transfer efficiency. The temperature of the surrounding fluid is also decreased. The bubble passage disrupts the flow structure, particularly impacting the boundary layer and vortex structure. These perturbations in temperature and flow structure constitute a secondary factor influencing heat transfer. The efficiency of heat transfer varies significantly across different surfaces; surfaces with a larger thin liquid film region exhibit the most significant improvement, followed by the downstream surface where the flow and temperature fields are most affected. This study advances the fundamental comprehension of the complex interaction between an evaporating bubble and a heated pillar in a microchannel, integrating a detailed analysis of the relevant transport mechanisms.