Guilherme Faria Moura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guilherme Faria Moura has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Gustavo Mendonça
Virginia Commonwealth University, USA
3 shared publications - Adilson Yoshio Furuse
Department of Operative Dentistry, Endodontics and Dental Materials, Bauru School of Dentistry, University of Sao Paulo, Bauru, SP, Brazil
1 shared publication - Caio Cesar Dias Resende
Unitri, Brazil
1 shared publication - Fabio Antonio Piola Rizzante
Associate Professor and Assistant Dean for Innovation, James B. Edwards College of Dental Medicine, Medical University of South Carolina (MUSC), Charleston, SC
1 shared publication - Flávio Domingues das Neves
Federal University of Uberlândia
1 shared publication - Fábio Henrique de Paulo Costa Santos
Federal University of Uberlândia
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Brazilian Oral Research
- Vol. 38, e063
Influence of fabrication method on the marginal fit of temporary restorations
Computer-aided manufacturing (CAM) technology allows the use of different manufacturing techniques. This in vitro study aimed to evaluate the marginal fit of temporary restorations manufactured using conventional chairside methods, milling, and three-dimensional printing. Fifteen 3-element temporary restorations specimens were produced and categorized into three groups: non-digital, obtained using the conventional chairside method (GC); milled (GM); and three-dimensionally printed (GP). Marginal fit was assessed using scanning electron microscopy (SEM) performed under two conditions: one with only the central screw tightened, and the other with all three screws tightened. Horizontal misfit values were categorized as over-, equal-, and under-extended and qualitatively analyzed. Statistical analysis was performed using the Tukey–Kramer test (α=0.05). In the vertical assessment, three-dimensionally printed restorations demonstrated greater misfit than restorations obtained by milling and the conventional chairside method (P<0.05). In the horizontal assessment, the misfit in the GP group was significantly higher than that in the GM and GC groups. Restorations obtained using the conventional chairside method and milled provisional restorations showed more favorable results than three-dimensionally printed restorations.
- 1 January 2024
- Published by FapUNIFESP (SciELO) in Brazilian Oral Research
- Vol. 38, e063
Open AccessInfluence of fabrication method on the marginal fit of temporary restorations
Computer-aided manufacturing (CAM) technology allows the use of different manufacturing techniques. This in vitro study aimed to evaluate the marginal fit of temporary restorations manufactured using conventional chairside methods, milling, and three-dimensional printing. Fifteen 3-element temporary restorations specimens were produced and categorized into three groups: non-digital, obtained using the conventional chairside method (GC); milled (GM); and three-dimensionally printed (GP). Marginal fit was assessed using scanning electron microscopy (SEM) performed under two conditions: one with only the central screw tightened, and the other with all three screws tightened. Horizontal misfit values were categorized as over-, equal-, and under-extended and qualitatively analyzed. Statistical analysis was performed using the Tukey–Kramer test (α=0.05). In the vertical assessment, three-dimensionally printed restorations demonstrated greater misfit than restorations obtained by milling and the conventional chairside method (P<0.05). In the horizontal assessment, the misfit in the GP group was significantly higher than that in the GM and GC groups. Restorations obtained using the conventional chairside method and milled provisional restorations showed more favorable results than three-dimensionally printed restorations.
- 30 November 2022
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 128 (5) , 1102.e1-1102.e5
Can postpolymerization for 3D-printed interim restorations be improved?
- 30 November 2022
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 128 (5) , 1102.e1-1102.e5
Can postpolymerization for 3D-printed interim restorations be improved?
- 2 July 2021
- Published by Wiley in Journal of Esthetic and Restorative Dentistry
- Vol. 33 (8) , 1070-1076
A fully digital approach for implant fixed complete dentures: A case report
Introductions: Intraoral scanner has been widely used for implant impression in partially edentulous cases; however, its accuracy in the impression of full‐arch implant is still questionable.Clinical report: This clinical report presents a technique to check the accuracy of intraoral scanning for complete‐arch implant restorations using an implant index cast (The Glossary of Prosthodontic Terms 9th Edition) and a three‐dimensional printed cast. A clinical case of immediate loading on a maxillary edentulous patient illustrates the application of an implant index cast in implant fixed complete dentures (IFCDs).Discussion: The implant index cast was fabricated based on the immediate interim prosthesis and provides effective control of the fit of scanned files and printed models. Therefore, this approach allows a more predictable and accurate fit of the final prosthesis.Clinical significance: In this article, we present a technique to check the accuracy of the final prosthesis without the need for a conventional impression and final cast in a digital workflow. This proposed approach is demonstrated through a case report of a maxillary edentulous patient restored with immediate loaded IFCDs.
- 2 July 2021
- Published by Wiley in Journal of Esthetic and Restorative Dentistry
- Vol. 33 (8) , 1070-1076
A fully digital approach for implant fixed complete dentures: A case report
Introductions: Intraoral scanner has been widely used for implant impression in partially edentulous cases; however, its accuracy in the impression of full‐arch implant is still questionable.Clinical report: This clinical report presents a technique to check the accuracy of intraoral scanning for complete‐arch implant restorations using an implant index cast (The Glossary of Prosthodontic Terms 9th Edition) and a three‐dimensional printed cast. A clinical case of immediate loading on a maxillary edentulous patient illustrates the application of an implant index cast in implant fixed complete dentures (IFCDs).Discussion: The implant index cast was fabricated based on the immediate interim prosthesis and provides effective control of the fit of scanned files and printed models. Therefore, this approach allows a more predictable and accurate fit of the final prosthesis.Clinical significance: In this article, we present a technique to check the accuracy of the final prosthesis without the need for a conventional impression and final cast in a digital workflow. This proposed approach is demonstrated through a case report of a maxillary edentulous patient restored with immediate loaded IFCDs.