Modesto Cadenas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Modesto Cadenas has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Ruben Gonzalez
University of Oviedo
8 shared publications - Ma. del Rocío Fernández
Department of Mechanical Engineering, University of Oviedo, 33203 Gijón, Spain
7 shared publications - Alberto García
Department of Construction and Manufacturing Engineering, University of Oviedo, 33204 Gijon, Spain
4 shared publications - José Manuel Cuetos Megido
University of Oviedo
4 shared publications - Antolin Hernández Battez
Department of Construction and Manufacturing Engineering, University of Oviedo, Pedro Puig Adam, s/n, 33203 Gijón, Spain
3 shared publications C. Navas
Departamento de Corrosión y Protección, Centro Nacional de Investigaciones Metalúrgicas (CENIM/CSIC), Avenida de Gregorio del Amo 8, 28040 Madrid, Spain
3 shared publications
Latest Publications
- 1 September 2017
- Published by Elsevier in Surface and Coatings Technology
- Vol. 324, 298-306
WC particles distribution model in the cross-section of laser cladded NiCrBSi + WC coatings, for different wt% WC
- 1 September 2017
- Published by Elsevier in Surface and Coatings Technology
- Vol. 324, 298-306
WC particles distribution model in the cross-section of laser cladded NiCrBSi + WC coatings, for different wt% WC
- 3 January 2017
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 26 (3) , 517-529
Tribological and Oxidative Behavior of Thermally Sprayed NiCrBSi Coatings
- 3 January 2017
- Published by Springer Nature in Journal of Thermal Spray Technology
- Vol. 26 (3) , 517-529
Tribological and Oxidative Behavior of Thermally Sprayed NiCrBSi Coatings
- Top Cited Papers
Effect of actual WC content on the reciprocating wear of a laser cladding NiCrBSi alloy reinforced with WC
- 10 August 2012
- Published by Springer Nature
- p. 141-148
Position Problem in Assur’s Groups with Revolute Pairs
- 10 August 2012
- Published by Springer Nature
- p. 141-148
Position Problem in Assur’s Groups with Revolute Pairs
- 1 January 2011
- Published by Inderscience Publishers in International Journal of Surface Science and Engineering
- Vol. 5 (2/3) , 75
NiCrBSi coatings textured by Nd-YAG laser
This work presents and discusses the influence of Nd-YAG laser parameters on the texturing of a low laser absorptivity NiCrBSi coating obtained by diode laser cladding. In order to obtain statistical significance, different kinds of design of experiments were considered, choosing a central composite inscribed design as the best according to the number of factors and required runs. In the first stage, a diode laser is used to obtain the NiCrBSi coating and in the second stage an Nd-YAG laser is used to generate surface texturing. Finally, results are observed with a confocal microscope, obtaining diameter and depth of the dimples and statistically studied plotting Pareto charts and response surfaces. The study led to the following conclusions: higher energies and spot diameters generate dimples with larger diameters; low energies and shorter pulse duration involves greater diameters; at high energies diameters remain nearly constant versus pulse duration; at higher energies, shorter pulse durations show greater depths; and at low energies depth remains almost constant versus pulse duration.
- 1 January 2011
- Published by Inderscience Publishers in International Journal of Surface Science and Engineering
- Vol. 5 (2/3) , 75
NiCrBSi coatings textured by Nd-YAG laser
This work presents and discusses the influence of Nd-YAG laser parameters on the texturing of a low laser absorptivity NiCrBSi coating obtained by diode laser cladding. In order to obtain statistical significance, different kinds of design of experiments were considered, choosing a central composite inscribed design as the best according to the number of factors and required runs. In the first stage, a diode laser is used to obtain the NiCrBSi coating and in the second stage an Nd-YAG laser is used to generate surface texturing. Finally, results are observed with a confocal microscope, obtaining diameter and depth of the dimples and statistically studied plotting Pareto charts and response surfaces. The study led to the following conclusions: higher energies and spot diameters generate dimples with larger diameters; low energies and shorter pulse duration involves greater diameters; at high energies diameters remain nearly constant versus pulse duration; at higher energies, shorter pulse durations show greater depths; and at low energies depth remains almost constant versus pulse duration.
- 1 January 2011
- Published by ASME International
- p. 55-57
Microstructure of NiCrBSi Laser Cladding Coatings Textured by Nd-YAG Laser
The use of texturing as a surface treatment that improves the tribological behavior is widespread in industrial and scientific fields, it is used in internal combustion engines [1], in biomechanical applications [2], in manufacturing processes [3] and in a full range of different applications. When texturing is carried out at low energy levels, the material melts superficially in a process governed by convection and thermocapillarity phenomena [4], whereas at high energy levels the reaction of the material could lead to its sudden vaporization [5] and local melting.
- 1 January 2011
- Published by ASME International
- p. 55-57
Microstructure of NiCrBSi Laser Cladding Coatings Textured by Nd-YAG Laser
The use of texturing as a surface treatment that improves the tribological behavior is widespread in industrial and scientific fields, it is used in internal combustion engines [1], in biomechanical applications [2], in manufacturing processes [3] and in a full range of different applications. When texturing is carried out at low energy levels, the material melts superficially in a process governed by convection and thermocapillarity phenomena [4], whereas at high energy levels the reaction of the material could lead to its sudden vaporization [5] and local melting.