Delma de Mattos Vidal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Delma de Mattos Vidal has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- D. de Carvalho Urashima
Department of Civil Engineering, Federal Center for Technological Education of Minas Gerais – CEFET-MG, Amazonas Avenue, 7675, Nova Gameleira, CEP 30510-000, Belo Horizonte, MG, Brazil
2 shared publications - Jefferson Lins da Silva
Universidade de São Paulo
2 shared publications - Mag Geisielly Alves Guimarães
Federal Center for Technological Education of Minas Gerais, CEFET/MG
2 shared publications - Rodrigo Alves e Silva
GeoEngineering Centre at Queen's-RMC, Queen's University
2 shared publications - C. A. C. Castro
Mechatronics Department, Federal Center for Technological Education of Minas Gerais – CEFET-MG, Imigrantes Avenue, 1000, Vargem, CEP 37022-560, Varginha, MG, Brazil
1 shared publication - Carina Maria Lins Costa
Universidade Federal do Rio Grande do Norte
1 shared publication
Latest Publications
- 31 January 2025
- Published by Emerald Publishing in Geosynthetics International
- Vol. 32 (1) , 169-179
Natural weathering effects of nonwoven geotextile exposed to different climate conditions
Humidity, air temperature, rainfall and solar radiation all contribute to the weathering of geosynthetics. Over time, their useful life can be affected and changes in properties can be observed, which affects the performance of these materials. As geosynthetics durability analyses must encompass each work condition, assessing the climate effects is essential for design purposes. This study exposed a nonwoven needle-punched poly(ethylene) terephthalate geotextile to natural weathering in three Brazilian cities (different exogenous environments) for 18 months. Mechanical tests were conducted to evaluate the geotextile changes due to weathering. This was demonstrated by the results: exposure to weather leads to the deterioration of the geotextile mechanical properties and increased stiffness. After four months, the tensile strength fell by half, while the deformation needed more than 12 months to have this same reduction; ultraviolet radiation intensity was the most effective weathering condition in the field; humidity and rainfall can affect the stiffness of geotextiles; the impact of accumulated climate factors gradually showed a convergence in the response of geotextile to weathering. Thus, this work highlights the need to evaluate the climate conditions in each location to understand the material's behavior on the exposure time.
- 31 January 2025
- Published by Emerald Publishing in Geosynthetics International
- Vol. 32 (1) , 169-179
Natural weathering effects of nonwoven geotextile exposed to different climate conditions
Humidity, air temperature, rainfall and solar radiation all contribute to the weathering of geosynthetics. Over time, their useful life can be affected and changes in properties can be observed, which affects the performance of these materials. As geosynthetics durability analyses must encompass each work condition, assessing the climate effects is essential for design purposes. This study exposed a nonwoven needle-punched poly(ethylene) terephthalate geotextile to natural weathering in three Brazilian cities (different exogenous environments) for 18 months. Mechanical tests were conducted to evaluate the geotextile changes due to weathering. This was demonstrated by the results: exposure to weather leads to the deterioration of the geotextile mechanical properties and increased stiffness. After four months, the tensile strength fell by half, while the deformation needed more than 12 months to have this same reduction; ultraviolet radiation intensity was the most effective weathering condition in the field; humidity and rainfall can affect the stiffness of geotextiles; the impact of accumulated climate factors gradually showed a convergence in the response of geotextile to weathering. Thus, this work highlights the need to evaluate the climate conditions in each location to understand the material's behavior on the exposure time.
- Open Access
- 31 July 2023
- Published by Brazilian Journals in REVISTA DELOS
- Vol. 16 (45) , 1732-1747
Sludge dewatering with geotextile refill in a draining container: case study in a water treatment plant
Population growth culminates in the generation of a significant amount of waste, including waste generated by water treatment processes, which results in a wet waste called effluent. This effluent must be treated and cannot be released directly into nature. One of its treatment steps is the separation of the solid and liquid phases, through dewatering techniques. This work presents a case study that uses a dewatering technique with geotextile tubes, on a mobile cradle composed of a roll on roll off container, an innovative technique that can significantly contribute to the sustainability and safety of the process. This case evaluates the operation of this technique in a complete cycle water treatment plant with an equalization tank, generating 20 m³ of sludge daily. Filtration and dewatering efficiencies are addressed, as well as increasing of the solids content by cake mass. Still, the ecosystem service of the water body in providing raw water is discussed and environmental valuation by indirect replacement cost method is briefly approached. Through the use of the dewatering technique in a special draining container, its effectiveness in separating the solid from the liquid phase can be seen, obtaining filtration efficiency greater than 90%, dewatering efficiency greater than 2000% and satisfactory solids contents for correct disposal at the authorized landfill. It is also noticed the environmental feasibility of using the dewatering technique, where the cost of its use represents less than 6% of the environmental value attributed to the water body in providing raw water for the station.
- 31 July 2023
- Published by Brazilian Journals in REVISTA DELOS
- Vol. 16 (45) , 1732-1747
Open AccessSludge dewatering with geotextile refill in a draining container: case study in a water treatment plant
Population growth culminates in the generation of a significant amount of waste, including waste generated by water treatment processes, which results in a wet waste called effluent. This effluent must be treated and cannot be released directly into nature. One of its treatment steps is the separation of the solid and liquid phases, through dewatering techniques. This work presents a case study that uses a dewatering technique with geotextile tubes, on a mobile cradle composed of a roll on roll off container, an innovative technique that can significantly contribute to the sustainability and safety of the process. This case evaluates the operation of this technique in a complete cycle water treatment plant with an equalization tank, generating 20 m³ of sludge daily. Filtration and dewatering efficiencies are addressed, as well as increasing of the solids content by cake mass. Still, the ecosystem service of the water body in providing raw water is discussed and environmental valuation by indirect replacement cost method is briefly approached. Through the use of the dewatering technique in a special draining container, its effectiveness in separating the solid from the liquid phase can be seen, obtaining filtration efficiency greater than 90%, dewatering efficiency greater than 2000% and satisfactory solids contents for correct disposal at the authorized landfill. It is also noticed the environmental feasibility of using the dewatering technique, where the cost of its use represents less than 6% of the environmental value attributed to the water body in providing raw water for the station.
- Open Access
- 10 February 2023
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 9 (1) , 1-2
Guest Editorial for the Special Issue on “Geosynthetics in Mining”
- 10 February 2023
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 9 (1) , 1-2
Open AccessGuest Editorial for the Special Issue on “Geosynthetics in Mining”
- 31 January 2023
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 9 (1) , 1-9
Installation Damage of a Geogrid Employed for Stabilization in a Mining Area
- 31 January 2023
- Published by Springer Nature in International Journal of Geosynthetics and Ground Engineering
- Vol. 9 (1) , 1-9
Installation Damage of a Geogrid Employed for Stabilization in a Mining Area
- 1 April 2022
- Published by Elsevier in Geotextiles and Geomembranes
- Vol. 50 (2) , 347-356
Uni and bi-directional dewatering behaviour of open geotextile containers used for filtration of waste slurries
- 1 April 2022
- Published by Elsevier in Geotextiles and Geomembranes
- Vol. 50 (2) , 347-356
Uni and bi-directional dewatering behaviour of open geotextile containers used for filtration of waste slurries
- 1 June 2019
- Published by Emerald Publishing in Geosynthetics International
- Vol. 26 (3) , 261-272
A new image-based technique for measuring pore size distribution of nonwoven geotextiles
The use of digital images to evaluate geotextile characteristics has appeared in the scientific literature, particularly for estimating the pore size distribution (PSD) of nonwoven geotextiles used for filtration purposes. While numerous image analysis techniques for PSD curve estimation have been proposed, automation of the analysis methods has received almost no attention. The goal of the present study is to quantify PSD curves from images of representative geotextile specimens using a fully automatic algorithm and considering the concept of largest inscribing opening size. These features are incorporated in a software program (GeotexInspector) developed by the second author. GeotexInspector is based on the concept of classification using the Support Vector Machine technique and digital image processing. These techniques are combined to develop a tool with a robust learning algorithm to identify geotextile fibers and pores. PSD curves from continuous filament and staple fiber nonwoven geotextiles are estimated using GeotexInspector and then compared with theoretical models that have appeared in the literature. The results indicate that the curves obtained from image analysis are in good agreement with model outcomes for models focused on the structure of geotextiles that are similar to the geotextiles used in this study.
- 1 June 2019
- Published by Emerald Publishing in Geosynthetics International
- Vol. 26 (3) , 261-272
A new image-based technique for measuring pore size distribution of nonwoven geotextiles
The use of digital images to evaluate geotextile characteristics has appeared in the scientific literature, particularly for estimating the pore size distribution (PSD) of nonwoven geotextiles used for filtration purposes. While numerous image analysis techniques for PSD curve estimation have been proposed, automation of the analysis methods has received almost no attention. The goal of the present study is to quantify PSD curves from images of representative geotextile specimens using a fully automatic algorithm and considering the concept of largest inscribing opening size. These features are incorporated in a software program (GeotexInspector) developed by the second author. GeotexInspector is based on the concept of classification using the Support Vector Machine technique and digital image processing. These techniques are combined to develop a tool with a robust learning algorithm to identify geotextile fibers and pores. PSD curves from continuous filament and staple fiber nonwoven geotextiles are estimated using GeotexInspector and then compared with theoretical models that have appeared in the literature. The results indicate that the curves obtained from image analysis are in good agreement with model outcomes for models focused on the structure of geotextiles that are similar to the geotextiles used in this study.
- 1 May 2017
- Published by Emerald Publishing in Geosynthetics International
- Vol. 24 (2) , 213-223
Degradation of polypropylene woven geotextile: tensile creep and weathering
Maintaining satisfactory properties in geosynthetics exposed to factors that could lead to their degradation needs to be considered in projects employing these materials. Geosynthetics subjected to tensile creep and weathering can undergo premature degradation over time. It is essential to study the influence of these factors, since they could act simultaneously in some applications. To assess the synergetic effects, frames were developed and four groups of a woven geotextile polypropylene sample were tested. The first and second groups were subjected to tensile creep at 5% and 10% of the tensile strength in conjunction with weathering for 2160 h. The third group was exposed to the same weathering conditions without tensile load. The fourth group was subjected to tensile creep at 10% of the tensile strength in laboratory conditions. Frames were built with a slope similar to the location of exposure to guarantee greater effects of weathering on the material surface. A meteorological station at the site monitored the meteorological parameters. The degradation suffered by the geotextile was determined by comparing tensile strength test results. The results presented show the importance of the constructed frames in assesssing tensile creep and weathering in the field under small loads.
- 1 May 2017
- Published by Emerald Publishing in Geosynthetics International
- Vol. 24 (2) , 213-223
Degradation of polypropylene woven geotextile: tensile creep and weathering
Maintaining satisfactory properties in geosynthetics exposed to factors that could lead to their degradation needs to be considered in projects employing these materials. Geosynthetics subjected to tensile creep and weathering can undergo premature degradation over time. It is essential to study the influence of these factors, since they could act simultaneously in some applications. To assess the synergetic effects, frames were developed and four groups of a woven geotextile polypropylene sample were tested. The first and second groups were subjected to tensile creep at 5% and 10% of the tensile strength in conjunction with weathering for 2160 h. The third group was exposed to the same weathering conditions without tensile load. The fourth group was subjected to tensile creep at 10% of the tensile strength in laboratory conditions. Frames were built with a slope similar to the location of exposure to guarantee greater effects of weathering on the material surface. A meteorological station at the site monitored the meteorological parameters. The degradation suffered by the geotextile was determined by comparing tensile strength test results. The results presented show the importance of the constructed frames in assesssing tensile creep and weathering in the field under small loads.
- 1 October 2014
- Published by Emerald Publishing in Geosynthetics International
- Vol. 21 (5) , 310-320
Dewatering of sludge from a water treatment plant in geotextile closed systems
Sludges generated during purification of water for human consumption are produced in large volumes and have high environmental polluting potential. The sludge dewatering technique using geotextile closed systems has been used to reduce the sludge volume for final disposal. It is a system that allows encapsulation, insulation, dewatering and disposal of sludge, which allows control of the input and output variables of the system. Also known as geotextile tubes, geotextile containers and geotextile bags are a function of their size. This work presents a discussion about the main factors influencing this sludge dewatering technique and its applicability for sludges generated in a water treatment plant. The study includes tests with single filling and with refilling the small geotextile bags in equipment constructed to simulate control of operational conditions, such as flow rate and pumping pressure. The evaluated performance of this system according to parameters proposed in the literature is also presented. The results obtained indicate that the efficiency of the dewatering technique depends on both the characteristics of the sludge and the geotextile properties. This study indicates the importance and efficiency of the dewatering technique in geotextile closed systems in reducing the sludge volume for final disposal.
- 1 October 2014
- Published by Emerald Publishing in Geosynthetics International
- Vol. 21 (5) , 310-320
Dewatering of sludge from a water treatment plant in geotextile closed systems
Sludges generated during purification of water for human consumption are produced in large volumes and have high environmental polluting potential. The sludge dewatering technique using geotextile closed systems has been used to reduce the sludge volume for final disposal. It is a system that allows encapsulation, insulation, dewatering and disposal of sludge, which allows control of the input and output variables of the system. Also known as geotextile tubes, geotextile containers and geotextile bags are a function of their size. This work presents a discussion about the main factors influencing this sludge dewatering technique and its applicability for sludges generated in a water treatment plant. The study includes tests with single filling and with refilling the small geotextile bags in equipment constructed to simulate control of operational conditions, such as flow rate and pumping pressure. The evaluated performance of this system according to parameters proposed in the literature is also presented. The results obtained indicate that the efficiency of the dewatering technique depends on both the characteristics of the sludge and the geotextile properties. This study indicates the importance and efficiency of the dewatering technique in geotextile closed systems in reducing the sludge volume for final disposal.
- 1 September 2013
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 36 (3) , 299-307
Numerical Analysis of Reinforcement Strains at Failure for Reinforced Embankments over Soft Soils
. The use of geosynthetics as basal reinforcement in embankments constructed over soft soils provides technical and economic benefits by improving the stability of the structure, reducing horizontal displacements, homogenizing differential settlements, and reducing time of construction. An adequate design should include, however, more than routine limit equilibrium analyses, and should focus on understanding the soil-reinforcement interaction and mobilization of reinforcement strains during construction and with time, aspects that can be assessed with the use of finite elements simulations. This article presents the results of finite elements simulations for a hypothetical embankment over soft soil, applying the conceptual framework developed by Rowe & Soderman (1987), Rowe et al. (1995) and Hinchberger & Rowe (2003). Two approximate methods for obtaining the reinforcement allowable compatible strain at failure without the need for numerical simulations also are compared and discussed. The results in this article highlight the importance of assessing the mobilization of reinforcement strains during construction and taking into account soil-reinforcement interaction, given that reinforcement strains must be compatible with the soil system. An important implication, often overlooked in the past, is that the specification of geosynthetic materials for this application should be based on a minimum reinforcement stiffness modulus, i.e., the ultimate strength of the material may not suffice as a specification parameter.
- 1 September 2013
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 36 (3) , 299-307
Numerical Analysis of Reinforcement Strains at Failure for Reinforced Embankments over Soft Soils
. The use of geosynthetics as basal reinforcement in embankments constructed over soft soils provides technical and economic benefits by improving the stability of the structure, reducing horizontal displacements, homogenizing differential settlements, and reducing time of construction. An adequate design should include, however, more than routine limit equilibrium analyses, and should focus on understanding the soil-reinforcement interaction and mobilization of reinforcement strains during construction and with time, aspects that can be assessed with the use of finite elements simulations. This article presents the results of finite elements simulations for a hypothetical embankment over soft soil, applying the conceptual framework developed by Rowe & Soderman (1987), Rowe et al. (1995) and Hinchberger & Rowe (2003). Two approximate methods for obtaining the reinforcement allowable compatible strain at failure without the need for numerical simulations also are compared and discussed. The results in this article highlight the importance of assessing the mobilization of reinforcement strains during construction and taking into account soil-reinforcement interaction, given that reinforcement strains must be compatible with the soil system. An important implication, often overlooked in the past, is that the specification of geosynthetic materials for this application should be based on a minimum reinforcement stiffness modulus, i.e., the ultimate strength of the material may not suffice as a specification parameter.
- 1 January 2008
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 31 (1) , 45-53
Analytical Solution for Luscher’s Problems on Two-Layer Consolidation
In this work, the problem of consolidation of two layers is discussed and analytical solutions for the specific case of Luscher’s problems are developed. Literature suggests that they are the first analytical solutions for problems that cannot be solved by the Gray-Barber closed form solutions for calculation of equivalent thickness. Luscher’s problems are solved using a generalization of the Sturm-Liouville problems for the solution of the partial differential equations. A discussion about the difficulties in generalizing these solutions is also presented. The solution obtained in this work is quantitatively different from that obtained by Luscher via integrated circuits.
- 1 January 2008
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 31 (1) , 45-53
Analytical Solution for Luscher’s Problems on Two-Layer Consolidation
In this work, the problem of consolidation of two layers is discussed and analytical solutions for the specific case of Luscher’s problems are developed. Literature suggests that they are the first analytical solutions for problems that cannot be solved by the Gray-Barber closed form solutions for calculation of equivalent thickness. Luscher’s problems are solved using a generalization of the Sturm-Liouville problems for the solution of the partial differential equations. A discussion about the difficulties in generalizing these solutions is also presented. The solution obtained in this work is quantitatively different from that obtained by Luscher via integrated circuits.