Abdalla Mohamed Elbendari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Abdalla Mohamed Elbendari has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Abdelazim Khalifa
Minerals Beneficiation and Agglomeration Department, Central Metallurgical Research and Development Institute, El Tebbin, P.O. Box 87, Cairo 11421, Egypt
1 shared publication - Ayman Abdel-Hamid El-Midany
Mining and Geological Engineering, Faculty of Engineering, Cairo University, Giza, Egypt
1 shared publication El-Sayed Hassan
1 shared publication- El-Sayed R. E. Hassan
Minerals Beneficiation and Agglomeration Department, Central Metallurgical Research and Development Institute, El Tebbin, Egypt
1 shared publication - Khaled Ezzat Yassin1 shared publication
M.K. Abdel-Rahman
Central Metallurgical R&D Institute, P.O. Box 87, Helwan, Cairo, Egypt
1 shared publication
Latest Publications
- 7 April 2025
- Published by Springer Nature in Euro-Mediterranean Journal for Environmental Integration
- Vol. 10 (4) , 2761-2772
Physical purification of Egyptian bentonite clay as a sustainable binder of El-Dekheila-iron-oxide-waste
- 7 April 2025
- Published by Springer Nature in Euro-Mediterranean Journal for Environmental Integration
- Vol. 10 (4) , 2761-2772
Physical purification of Egyptian bentonite clay as a sustainable binder of El-Dekheila-iron-oxide-waste
- Top Cited PapersOpen Access
- 27 January 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-18
Optimizing key parameters for grinding energy efficiency and modeling of particle size distribution in a stirred ball mill
Fine grinding using a stirred ball mill can enhance ore liberation but incurs high energy consumption, which can be minimized by optimizing operating conditions. This study explores the impact of key operational parameters—grinding time, stirrer tip speed, solid concentration, and feed size—on grinding efficiency, evaluated using specific energy inputs, in stirred milling of Egyptian copper ore. The particle size distribution (PSD) of ground products was simulated using the Gates–Gaudin-Schuhmann model (GGS) and the Rosin-Rammler-Benne (RRB) function. Taking minimum energy consumption into account, the finest particles (100% ~1 μm) were achieved at the maximum stirrer speed of 500 rpm and a moderate solid concentration of 33.3% after 17 h of grinding, consuming approximately 1225 kWh/t. Experimental data demonstrated a linear correlation between the natural logarithm of the cumulative retained fraction and particle size (µm). The proposed model accurately describes PSDs across different solid concentrations and grinding durations.
- 27 January 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-18
Top Cited PapersOpen AccessOptimizing key parameters for grinding energy efficiency and modeling of particle size distribution in a stirred ball mill
Fine grinding using a stirred ball mill can enhance ore liberation but incurs high energy consumption, which can be minimized by optimizing operating conditions. This study explores the impact of key operational parameters—grinding time, stirrer tip speed, solid concentration, and feed size—on grinding efficiency, evaluated using specific energy inputs, in stirred milling of Egyptian copper ore. The particle size distribution (PSD) of ground products was simulated using the Gates–Gaudin-Schuhmann model (GGS) and the Rosin-Rammler-Benne (RRB) function. Taking minimum energy consumption into account, the finest particles (100% ~1 μm) were achieved at the maximum stirrer speed of 500 rpm and a moderate solid concentration of 33.3% after 17 h of grinding, consuming approximately 1225 kWh/t. Experimental data demonstrated a linear correlation between the natural logarithm of the cumulative retained fraction and particle size (µm). The proposed model accurately describes PSDs across different solid concentrations and grinding durations.
- Open Access
- 9 December 2023
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 59 (6)
Optimizing the removal of iron oxide from Egyptian feldspar ore
The demand for feldspar as a raw material for various industrial applications continuously increases. Feldspar is a primary raw material in manufacturing ceramics, glass, fillers, welding electrodes, and enamel. Feldspar is often associated with iron oxide, which decreases its economic value and hinders its industrial application. The present work aimed at reducing iron oxide content in Egyptian feldspar ore from the Wadi Zerabi locality. Ball milling was used for preparing feldspar feed of size -250+45µm. Carpco dry high-intensity magnetic separation followed by acid leaching processes were carried out in order to decrease the iron contamination and increase the feldspar content. A Box-Behnken statistical design was used to optimize the magnetic separation results. From a feldspar feed containing 1.40% Fe2O3, a non-magnetic concentrate of 0.25% Fe2O3 was obtained. The Fe2O3 removal reached up to 82% with a high yield as the % weight of non-magnetic feldspar reached up to 97.5%. The leaching process further reduced the iron oxide content down to 0.19 %. Also, the feldspar whiteness was improved from 65.17% in the original ore to 85.60% in the leached product.
- 9 December 2023
- Published by Politechnika Wroclawska Oficyna Wydawnicza in Physicochemical Problems of Mineral Processing
- Vol. 59 (6)
Open AccessOptimizing the removal of iron oxide from Egyptian feldspar ore
The demand for feldspar as a raw material for various industrial applications continuously increases. Feldspar is a primary raw material in manufacturing ceramics, glass, fillers, welding electrodes, and enamel. Feldspar is often associated with iron oxide, which decreases its economic value and hinders its industrial application. The present work aimed at reducing iron oxide content in Egyptian feldspar ore from the Wadi Zerabi locality. Ball milling was used for preparing feldspar feed of size -250+45µm. Carpco dry high-intensity magnetic separation followed by acid leaching processes were carried out in order to decrease the iron contamination and increase the feldspar content. A Box-Behnken statistical design was used to optimize the magnetic separation results. From a feldspar feed containing 1.40% Fe2O3, a non-magnetic concentrate of 0.25% Fe2O3 was obtained. The Fe2O3 removal reached up to 82% with a high yield as the % weight of non-magnetic feldspar reached up to 97.5%. The leaching process further reduced the iron oxide content down to 0.19 %. Also, the feldspar whiteness was improved from 65.17% in the original ore to 85.60% in the leached product.
- Open Access
- 1 November 2023
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 1 (2) , 361–366
Optimizing Dry Ultrafine Grinding of Talc in Attritor Mill
In this work, the parameters affecting the dry grinding of talc in the attritor mill were investigated. The attritor was tested with its initial design without balls then with balls as additional grinding media to prepare a feed passing 45 microns. The prepared feed (-45 mm) was used to produce a product with 10 μm or less using statistical design in presence of balls. The presence of balls enhances product fineness. The significance of the studied factors is: stirrer speed>mill filling >grinding time. In addition, the d 50 was correlated with studied factors. The mean particle size (d 50 ) as low as 6 μm was obtained at 460 rpm, 20% mill filling, and after 60 min grinding time.
- 1 November 2023
- Published by Polish Mineral Engineering Society in Inżynieria Mineralna
- Vol. 1 (2) , 361–366
Open AccessOptimizing Dry Ultrafine Grinding of Talc in Attritor Mill
In this work, the parameters affecting the dry grinding of talc in the attritor mill were investigated. The attritor was tested with its initial design without balls then with balls as additional grinding media to prepare a feed passing 45 microns. The prepared feed (-45 mm) was used to produce a product with 10 μm or less using statistical design in presence of balls. The presence of balls enhances product fineness. The significance of the studied factors is: stirrer speed>mill filling >grinding time. In addition, the d 50 was correlated with studied factors. The mean particle size (d 50 ) as low as 6 μm was obtained at 460 rpm, 20% mill filling, and after 60 min grinding time.
- Open Access
- 1 January 2021
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 248, 260-271
Increasing the efficiency of phosphate ore processing using flotation method
The paper presents flotation of two phosphate ore samples of different origin. Statistical analysis was used to study the effect of operating parameters on flotation efficiency. The paper proposes to increase the efficiency of flotation processing of magmatic phosphate ore with a low grade of the valuable component (P2O5 = 10.88 %), containing nepheline and feldspars, by means of direct anionic flotation. Authors present an optimization of anionic flotation using tall oil fatty acids mixed with anionic phospholane as an anionic collector. The effect of adding soda ash to compensate for the influence of calcium cations on technological parameters of P2O5 flotation was examined. The results of studying the flotation of nepheline ore (flotation tailings of magmatic phosphate ore) showed that replacement of phospholane with oxyethylated isotridecanol allowed to obtain a high-quality concentrate. It was estimated that with the addition of Na2CO3 in the amount of 2,000 g/t, a concentrate was obtained with the grade and recovery of phosphorus pentoxide equal to 39.15 and 94.19 %, respectively. The paper proposes to increase the efficiency of flotation processing of sedimentary phosphate ore with a low grade of the valuable component (P2O5 = 22.5 %), containing gypsum and quartz, by means of desliming followed by anionic or cationic reverse flotation. Tall oil fatty acid with anionic phospholane was used as a collector in anionic reverse flotation, and amine was used in cationic reverse flotation. Sodium tripolyphosphate was used as a P2O5 depressant. It was found to be an effective depressant in both anionic and cationic flotation. When analyzing the statistical plan, it was estimated that the maximum grade of the valuable component in the concentrate (P2O5 = 31.23 %) and the recovery to concentrate of 95.22 % were obtained in the chamber product at amine consumption of 950.88 g/t and sodium tripolyphosphate consumption of 500 g/t.
- 1 January 2021
- Published by Saint-Petersburg Mining University in Journal of Mining Institute
- Vol. 248, 260-271
Open AccessIncreasing the efficiency of phosphate ore processing using flotation method
The paper presents flotation of two phosphate ore samples of different origin. Statistical analysis was used to study the effect of operating parameters on flotation efficiency. The paper proposes to increase the efficiency of flotation processing of magmatic phosphate ore with a low grade of the valuable component (P2O5 = 10.88 %), containing nepheline and feldspars, by means of direct anionic flotation. Authors present an optimization of anionic flotation using tall oil fatty acids mixed with anionic phospholane as an anionic collector. The effect of adding soda ash to compensate for the influence of calcium cations on technological parameters of P2O5 flotation was examined. The results of studying the flotation of nepheline ore (flotation tailings of magmatic phosphate ore) showed that replacement of phospholane with oxyethylated isotridecanol allowed to obtain a high-quality concentrate. It was estimated that with the addition of Na2CO3 in the amount of 2,000 g/t, a concentrate was obtained with the grade and recovery of phosphorus pentoxide equal to 39.15 and 94.19 %, respectively. The paper proposes to increase the efficiency of flotation processing of sedimentary phosphate ore with a low grade of the valuable component (P2O5 = 22.5 %), containing gypsum and quartz, by means of desliming followed by anionic or cationic reverse flotation. Tall oil fatty acid with anionic phospholane was used as a collector in anionic reverse flotation, and amine was used in cationic reverse flotation. Sodium tripolyphosphate was used as a P2O5 depressant. It was found to be an effective depressant in both anionic and cationic flotation. When analyzing the statistical plan, it was estimated that the maximum grade of the valuable component in the concentrate (P2O5 = 31.23 %) and the recovery to concentrate of 95.22 % were obtained in the chamber product at amine consumption of 950.88 g/t and sodium tripolyphosphate consumption of 500 g/t.
- Open Access
- 28 August 2019
- Published by Springer Nature
- p. 59-65
Mineralogical and Technological Aspects of Phosphate Ore Processing
- 28 August 2019
- Published by Springer Nature
- p. 59-65
Open AccessMineralogical and Technological Aspects of Phosphate Ore Processing