XZXuejing Zhang

Xuejing Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Xuejing Zhang has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimizing the Clearance Fit of a Progressive Cavity Pump for the Thermal Recovery of Petroleum Using Fluid–Structure Thermal Coupling

    by Xuejing Zhang, Junhu Yang, Chong Ma, Yubing Gong, Junxiong Fang, Wei Han

    It is important to incorporate the effects of fluid-structure thermal coupling and the boundary conditions when calculating the thermal dynamics and response of progressive cavity pumps. This study develops a fluid-structure thermal coupling model of the progressive cavity pump to improve the accuracy of its measured field of deformation and the temperature field of the stator. A function for the macroscopic motion of a rigid body is written in a typical fluid domain, and the user-defined function (UDF) in FLUENT is used to load the boundary of the rotor to realize its planetary motion. Local remeshing is used to update the moving grid, and the viscoelastic hysteretic heat of the stator is treated as the internal source of heat. One-way decoupling is used based on tire slip theory, and heat flux on the surface of the stator is calculated by the ANSYS Parametric Design Language (APDL). The sequential fluid-structure thermal coupling of the progressive cavity pump is calculated by using the ANSYS workbench. A scheme for optimizing the fit clearance of the stator and rotor is given to improve the volumetric efficiency of the progressive cavity pump and prevent the stator from being stuck owing to a large deformation, and the calculations are verified by experiments on volumetric efficiency. The average deviation in the calculated volumetric efficiency was less than 5% compared with the experimental values. The proposed scheme provides a theoretical basis for the optimal design of the progressive cavity pump for the thermal production of petroleum.


  • Open Access

    Optimal design and numerical analysis of multi-field coupling in a screw pump under wet gas compression

    by Xuejing Zhang, Junhu Yang, Li Wang, Chong Ma, Wei Han, Yubing Gong

    During on-site operation under wet gas compression, the volumetric efficiency of a twin-screw pump decreases sharply, the temperature in the pump rises significantly, severe vibration and even jamming can occur. To solve the problems caused by wet gas compression structurally, a method for optimizing the design of a decompression screw is proposed in this paper based on the characteristics of a twin-screw pump and screw compressor. A fluid–solid multi-field thermal-coupling scheme is used to calculate the pressure, temperature, deformation, outflow, and volumetric efficiency of a screw pump before and after optimization. The average deviation between the calculated outflow and the experimental results was no more than 5%, demonstrating the accuracy of the calculation. After optimization, the return flow between the pump stages was significantly reduced and the outflow had increased. When the pressure difference between the inlet and outlet was 1 MPa, the maximum increase was about 18%. With an increase of the gas volume fraction from 95% to 99%, the average increase of the volumetric efficiency was about 14%. The temperature rise in the chambers at all levels and the temperature difference between the inlet and outlet of the decompression screw pump were lower than those of a traditional screw pump. The deformations at the three clearances were also less than those of a traditional screw pump, which helps to avoid jamming caused by thermal expansion.


  • Open Access

    The influence of gas volume fractions on deformation and volumetric efficiency of twin-screw multiphase pump based on fluid–thermal–structure coupling numerical calculation

    by Xuejing Zhang, Junhu Yang, Chong Ma, Wei Han, Deqiang Wei, Ting Lan

    The twin-screw multiphase pump shows a significant phenomenon of fluid–thermal–structure physics field coupling. The method of studying dynamics, thermodynamic characteristics, and deformation of the screw pump is biased from the actual boundary conditions without considering multi-field coupling. To enhance the calculation accuracy of the twin-screw pump integrated deformation field and further determine the clearances between rotors and pump liner, the fluid–thermal–structure coupling calculation is completed by ANSYS WORKBENCH. The calculation results of the leakage rate are verified by experiments. The moving reference frame dynamic mesh method is used in the fluid domain numerical simulation, and the non-equilibrium wall function method is used to solve the boundary layer. The rotor and pump liner deformations and their influences on volumetric efficiency are studied under different gas volume fractions. The optimal installation clearances are proposed to reduce the leakage flow rate and prevent the rotor from sticking due to large deformation. The results show that the calculated results of the leakage rate are in good agreement with the experimental values, and the average deviation is less than 4%. The research program effectively ensures the calculation accuracy and efficiency of the whole model and provides an important basis for the optimal design of the twin-screw pump.


  • Open Access

    Research on the Prediction Method of Centrifugal Pump Performance Based on a Double Hidden Layer BP Neural Network

    by Wei Han, Lingbo Nan, Min Su, Yu Chen, Rennian Li, Xuejing Zhang

    With the aim of improving the shortcomings of the traditional single hidden layer back propagation (BP) neural network structure and learning algorithm, this paper proposes a centrifugal pump performance prediction method based on the combination of the Levenberg–Marquardt (LM) training algorithm and double hidden layer BP neural network. MATLAB was used to establish a double hidden layer BP neural network prediction model to predict the head and efficiency of a centrifugal pump. The average relative error of the head between the experimental and prediction obtained by the double hidden layer BP neural network model was 4.35%, the average relative error of the model prediction efficiency and the experimental efficiency was 2.94%, and the convergence time was 1/42 of that of the single hidden layer. The double hidden layer BP neural network model effectively solves the problems of low learning efficiency and easy convergence into local minima—issues that were common in the traditional single hidden layer BP neural network training. Furthermore, the proposed model realizes hydraulic performance prediction during the design process of a centrifugal pump.