Jana Hrdá
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jana Hrdá has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Michaela Sojková
Institute of Electrical Engineering, Slovak Academy of Sciences, Dúbravská cesta 9, 84104 Bratislava, Slovakia
9 shared publications - Martin Hulman
Institute of Electrical Engineering SAS, Dúbravska cesta 9, 841 04 Bratislava, Slovakia
7 shared publications - Peter Siffalovic
Institute of Physics, Slovak Academy of Sciences, 84511 Bratislava, Slovakia
6 shared publications - Lenka Pribusová Slušná
Institute of Electrical Engineering, Slovak Academy of Sciences, Dúbravská cesta 9, 84104 Bratislava, Slovakia
4 shared publications - Ashin Shaji
Slovak Academy of Sciences
3 shared publications Edmund Dobročka
Institute of Electrical Engineering SAS Dúbravská cesta 9 841 04 Bratislava Slovakia
3 shared publications
Latest Publications
- 9 February 2026
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 59 (2) , 316-325
Crystallite orientation and lateral material distribution in transition metal dichalcogenide thin films studied by laboratory GIWAXS
The chemical vapor deposition (CVD) technique is widely used to prepare transition metal dichalcogenide (TMD) thin films. Parameters such as precursors, type of substrate, temperature profile, gas flow through the CVD chamber and pressure can influence the orientation of TMD crystals in a thin film. In this context, the grazing-incidence wide-angle X-ray scattering (GIWAXS) technique serves as a promising tool for revealing the texture and spatial distribution of TMD crystalline domains in thin films. Here, a laboratory GIWAXS-based method is reported for the measurement of pole figures of textured TMD thin films. Additionally, GIWAXS tomography in grazing-incidence mode enables spatial mapping of the TMD crystalline domains in thin films. This unique combination of GIWAXS tomography and pole figure measurements allows advanced laboratory analysis of thin TMD films that was previously only possible on synchrotron beamlines.
- 9 February 2026
- Published by International Union of Crystallography (IUCr) in Journal of Applied Crystallography
- Vol. 59 (2) , 316-325
Crystallite orientation and lateral material distribution in transition metal dichalcogenide thin films studied by laboratory GIWAXS
The chemical vapor deposition (CVD) technique is widely used to prepare transition metal dichalcogenide (TMD) thin films. Parameters such as precursors, type of substrate, temperature profile, gas flow through the CVD chamber and pressure can influence the orientation of TMD crystals in a thin film. In this context, the grazing-incidence wide-angle X-ray scattering (GIWAXS) technique serves as a promising tool for revealing the texture and spatial distribution of TMD crystalline domains in thin films. Here, a laboratory GIWAXS-based method is reported for the measurement of pole figures of textured TMD thin films. Additionally, GIWAXS tomography in grazing-incidence mode enables spatial mapping of the TMD crystalline domains in thin films. This unique combination of GIWAXS tomography and pole figure measurements allows advanced laboratory analysis of thin TMD films that was previously only possible on synchrotron beamlines.
- 18 March 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (12)
Investigating structural, optical, and electron-transport properties of lithium intercalated few-layer MoS2 films: Unraveling the influence of disorder
Molybdenum disulfide is a promising candidate for various applications in electronics, optoelectronics, or alkali-ion batteries. The natural presence of the van der Waals gap allows intercalating alkali ions, such as lithium, into MoS2 films. Intercalation can modify the electronic structure as well as the electrical and optical properties. Here, we present a structural, optical, and electrical characterization of Li-intercalated few-layer MoS2 films. The intercalation was carried out by annealing MoS2 film in the presence of Li2S powder, serving as a lithium source. The initial MoS2 layers were prepared by pulsed laser deposition (PLD) and by sulfurization of 1 nm thick Mo film (TAC). The presence of lithium was confirmed by synchrotron-based x-ray Photoelectron Spectroscopy. The Raman spectroscopy, x-ray diffraction, and optical absorption measurements confirmed semiconducting behavior for all samples. All samples exhibited the thermally activated dependence of the electrical resistance, R, typical for the Efros–Shklovskii variable range hopping in a disordered semiconductor, ln R(T) ∝ (TES/T)1/2, where kBTES is the hopping activation energy. The PLD-grown MoS2 samples exhibited a relatively mild initial disorder primarily caused by grain boundaries. Lithium intercalation led to an increase in disorder, evident in the increase in kBTES and a substantial rise in electrical resistance. The TAC-grown undoped MoS2 sample already exhibited significant resistance, and the impact of Li intercalation on resistance was minimal. This observation was attributed to the fact that the TAC-grown MoS2 samples exhibit a perturbed stoichiometry (the S:Mo ratio ∼ 2.20), causing strong disorder even before Li intercalation. The electron doping caused by lithium, if any, was completely obscured by the effect of disorder.
- 18 March 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (12)
Investigating structural, optical, and electron-transport properties of lithium intercalated few-layer MoS2 films: Unraveling the influence of disorder
Molybdenum disulfide is a promising candidate for various applications in electronics, optoelectronics, or alkali-ion batteries. The natural presence of the van der Waals gap allows intercalating alkali ions, such as lithium, into MoS2 films. Intercalation can modify the electronic structure as well as the electrical and optical properties. Here, we present a structural, optical, and electrical characterization of Li-intercalated few-layer MoS2 films. The intercalation was carried out by annealing MoS2 film in the presence of Li2S powder, serving as a lithium source. The initial MoS2 layers were prepared by pulsed laser deposition (PLD) and by sulfurization of 1 nm thick Mo film (TAC). The presence of lithium was confirmed by synchrotron-based x-ray Photoelectron Spectroscopy. The Raman spectroscopy, x-ray diffraction, and optical absorption measurements confirmed semiconducting behavior for all samples. All samples exhibited the thermally activated dependence of the electrical resistance, R, typical for the Efros–Shklovskii variable range hopping in a disordered semiconductor, ln R(T) ∝ (TES/T)1/2, where kBTES is the hopping activation energy. The PLD-grown MoS2 samples exhibited a relatively mild initial disorder primarily caused by grain boundaries. Lithium intercalation led to an increase in disorder, evident in the increase in kBTES and a substantial rise in electrical resistance. The TAC-grown undoped MoS2 sample already exhibited significant resistance, and the impact of Li intercalation on resistance was minimal. This observation was attributed to the fact that the TAC-grown MoS2 samples exhibit a perturbed stoichiometry (the S:Mo ratio ∼ 2.20), causing strong disorder even before Li intercalation. The electron doping caused by lithium, if any, was completely obscured by the effect of disorder.
- 1 December 2023
- Published by Wiley in Physica Status Solidi (b)
- Vol. 260 (12)
Fourier‐Transform Infrared Spectroscopy of MoTe2 Thin Films
Molybdenum ditelluride (MoTe2), a member of the transition metal dichalcogenide family, holds significant promise in optoelectronic applications. To harness its full potential, it is imperative to understand its fundamental optical properties, including refractive indices. Herein, measurements of the transmittance and reflectance spectra of thin MoTe2 layers are conducted featuring hexagonal and monoclinic structures across the far‐infrared (IR) and mid‐IR spectral regions. These spectra are fitted, allowing to extract the complex refractive index and optical conductance. In the semiconducting hexagonal phase, both the conductance and extinction coefficient remain negligible below 3000 cm−1 and increase at higher energies. Conversely, the monoclinic phase exhibits a conductance peak in the far‐IR region and a continuous increase from 1000 to 6000 cm−1. The findings are compared with existing theoretical and experimental results to provide further insights into MoTe2's optical behavior.
- 1 December 2023
- Published by Wiley in Physica Status Solidi (b)
- Vol. 260 (12)
Fourier‐Transform Infrared Spectroscopy of MoTe2 Thin Films
Molybdenum ditelluride (MoTe2), a member of the transition metal dichalcogenide family, holds significant promise in optoelectronic applications. To harness its full potential, it is imperative to understand its fundamental optical properties, including refractive indices. Herein, measurements of the transmittance and reflectance spectra of thin MoTe2 layers are conducted featuring hexagonal and monoclinic structures across the far‐infrared (IR) and mid‐IR spectral regions. These spectra are fitted, allowing to extract the complex refractive index and optical conductance. In the semiconducting hexagonal phase, both the conductance and extinction coefficient remain negligible below 3000 cm−1 and increase at higher energies. Conversely, the monoclinic phase exhibits a conductance peak in the far‐IR region and a continuous increase from 1000 to 6000 cm−1. The findings are compared with existing theoretical and experimental results to provide further insights into MoTe2's optical behavior.
- Open Access
- 2 August 2023
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 35 (16) , 6246-6257
Lithium-Induced Reorientation of Few-Layer MoS2 Films
Molybdenum disulfide (MoS2) few-layer films have gained considerable attention for their possible applications in electronics and optics and also as a promising material for energy conversion and storage. Intercalating alkali metals, such as lithium, offers the opportunity to engineer the electronic properties of MoS2. However, the influence of lithium on the growth of MoS2 layers has not been fully explored. Here, we have studied how lithium affects the structural and optical properties of the MoS2 few-layer films prepared using a new method based on one-zone sulfurization with Li2S as a source of lithium. This method enables incorporation of Li into octahedral and tetrahedral sites of the already prepared MoS2 films or during MoS2 formation. Our results discover an important effect of lithium promoting the epitaxial growth and horizontal alignment of the films. Moreover, we have observed a vertical-to-horizontal reorientation in vertically aligned MoS2 films upon lithiation. The measurements show long-term stability and preserved chemical composition of the horizontally aligned Li-doped MoS2.
- 2 August 2023
- Published by American Chemical Society (ACS) in Chemistry of Materials
- Vol. 35 (16) , 6246-6257
Open AccessLithium-Induced Reorientation of Few-Layer MoS2 Films
Molybdenum disulfide (MoS2) few-layer films have gained considerable attention for their possible applications in electronics and optics and also as a promising material for energy conversion and storage. Intercalating alkali metals, such as lithium, offers the opportunity to engineer the electronic properties of MoS2. However, the influence of lithium on the growth of MoS2 layers has not been fully explored. Here, we have studied how lithium affects the structural and optical properties of the MoS2 few-layer films prepared using a new method based on one-zone sulfurization with Li2S as a source of lithium. This method enables incorporation of Li into octahedral and tetrahedral sites of the already prepared MoS2 films or during MoS2 formation. Our results discover an important effect of lithium promoting the epitaxial growth and horizontal alignment of the films. Moreover, we have observed a vertical-to-horizontal reorientation in vertically aligned MoS2 films upon lithiation. The measurements show long-term stability and preserved chemical composition of the horizontally aligned Li-doped MoS2.
- Open Access
- 3 July 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (28) , 34206-34214
Improved Gas Sensing Capabilities of MoS2/Diamond Heterostructures at Room Temperature
Molybdenum disulfide (MoS2) and nanocrystalline diamond (NCD) have attracted considerable attention due to their unique electronic structure and extraordinary physical and chemical properties in many applications, including sensor devices in gas sensing applications. Combining MoS2 and H-terminated NCD (H-NCD) in a heterostructure design can improve the sensing performance due to their mutual advantages. In this study, the synthesis of MoS2 and H-NCD thin films using appropriate physical/chemical deposition methods and their analysis in terms of gas sensing properties in their individual and combined forms are demonstrated. The sensitivity and time domain characteristics of the sensors were investigated for three gases: oxidizing NO2, reducing NH3, and neutral synthetic air. It was observed that the MoS2/H-NCD heterostructure-based gas sensor exhibits improved sensitivity to oxidizing NO2 (0.157%·ppm-1) and reducing NH3 (0.188%·ppm-1) gases compared to pure active materials (pure MoS2 achieves responses of 0.018%·ppm-1 for NO2 and -0.0072%·ppm-1 for NH3, respectively, and almost no response for pure H-NCD at room temperature). Different gas interaction model pathways were developed to describe the current flow mechanism through the sensing area with/without the heterostructure. The gas interaction model independently considers the influence of each material (chemisorption for MoS2 and surface doping mechanism for H-NCD) as well as the current flow mechanism through the formed P-N heterojunction.
- 3 July 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (28) , 34206-34214
Open AccessImproved Gas Sensing Capabilities of MoS2/Diamond Heterostructures at Room Temperature
Molybdenum disulfide (MoS2) and nanocrystalline diamond (NCD) have attracted considerable attention due to their unique electronic structure and extraordinary physical and chemical properties in many applications, including sensor devices in gas sensing applications. Combining MoS2 and H-terminated NCD (H-NCD) in a heterostructure design can improve the sensing performance due to their mutual advantages. In this study, the synthesis of MoS2 and H-NCD thin films using appropriate physical/chemical deposition methods and their analysis in terms of gas sensing properties in their individual and combined forms are demonstrated. The sensitivity and time domain characteristics of the sensors were investigated for three gases: oxidizing NO2, reducing NH3, and neutral synthetic air. It was observed that the MoS2/H-NCD heterostructure-based gas sensor exhibits improved sensitivity to oxidizing NO2 (0.157%·ppm-1) and reducing NH3 (0.188%·ppm-1) gases compared to pure active materials (pure MoS2 achieves responses of 0.018%·ppm-1 for NO2 and -0.0072%·ppm-1 for NH3, respectively, and almost no response for pure H-NCD at room temperature). Different gas interaction model pathways were developed to describe the current flow mechanism through the sensing area with/without the heterostructure. The gas interaction model independently considers the influence of each material (chemisorption for MoS2 and surface doping mechanism for H-NCD) as well as the current flow mechanism through the formed P-N heterojunction.
- 1 November 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (11) , 113909
A wide-angle X-ray scattering laboratory setup for tracking phase changes of thin films in a chemical vapor deposition chamber
The few-layer transition metal dichalcogenides (TMD) are an attractive class of materials due to their unique and tunable electronic, optical, and chemical properties, controlled by the layer number, crystal orientation, grain size, and morphology. One of the most commonly used methods for synthesizing the few-layer TMD materials is the chemical vapor deposition (CVD) technique. Therefore, it is crucial to develop in situ inspection techniques to observe the growth of the few-layer TMD materials directly in the CVD chamber environment. We demonstrate such an in situ observation on the growth of the vertically aligned few-layer MoS2 in a one-zone CVD chamber using a laboratory table-top grazing-incidence wide-angle X-ray scattering (GIWAXS) setup. The advantages of using a microfocus X-ray source with focusing Montel optics and a single-photon counting 2D X-ray detector are discussed. Due to the position-sensitive 2D X-ray detector, the orientation of MoS2 layers can be easily distinguished. The performance of the GIWAXS setup is further improved by suppressing the background scattering using a guarding slit, an appropriately placed beamstop, and He gas in the CVD reactor. The layer growth can be monitored by tracking the width of the MoS2 diffraction peak in real time. The temporal evolution of the crystallization kinetics can be satisfactorily described by the Avrami model, employing the normalized diffraction peak area. In this way, the activation energy of the particular chemical reaction occurring in the CVD chamber can be determined.
- 1 November 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (11) , 113909
A wide-angle X-ray scattering laboratory setup for tracking phase changes of thin films in a chemical vapor deposition chamber
The few-layer transition metal dichalcogenides (TMD) are an attractive class of materials due to their unique and tunable electronic, optical, and chemical properties, controlled by the layer number, crystal orientation, grain size, and morphology. One of the most commonly used methods for synthesizing the few-layer TMD materials is the chemical vapor deposition (CVD) technique. Therefore, it is crucial to develop in situ inspection techniques to observe the growth of the few-layer TMD materials directly in the CVD chamber environment. We demonstrate such an in situ observation on the growth of the vertically aligned few-layer MoS2 in a one-zone CVD chamber using a laboratory table-top grazing-incidence wide-angle X-ray scattering (GIWAXS) setup. The advantages of using a microfocus X-ray source with focusing Montel optics and a single-photon counting 2D X-ray detector are discussed. Due to the position-sensitive 2D X-ray detector, the orientation of MoS2 layers can be easily distinguished. The performance of the GIWAXS setup is further improved by suppressing the background scattering using a guarding slit, an appropriately placed beamstop, and He gas in the CVD reactor. The layer growth can be monitored by tracking the width of the MoS2 diffraction peak in real time. The temporal evolution of the crystallization kinetics can be satisfactorily described by the Avrami model, employing the normalized diffraction peak area. In this way, the activation energy of the particular chemical reaction occurring in the CVD chamber can be determined.
- 11 September 2022
- Published by Elsevier in Applied Surface Science
- Vol. 606
Stepwise sulfurization of MoO3 to MoS2 thin films studied by real-time X-ray scattering
- 11 September 2022
- Published by Elsevier in Applied Surface Science
- Vol. 606
Stepwise sulfurization of MoO3 to MoS2 thin films studied by real-time X-ray scattering
- Open Access
- 9 August 2021
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 11 (44) , 27292-27297
Tuning the charge carrier mobility in few-layer PtSe 2 films by Se : Pt ratio
This work presents the fabrication of horizontally aligned PtSe 2 films using one-zone selenization of pre-deposited platinum layers. We have identified the Se : Pt ratio as a parameter controlling the charge carrier mobility in the thin films.
- 9 August 2021
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 11 (44) , 27292-27297
Open AccessTuning the charge carrier mobility in few-layer PtSe 2 films by Se : Pt ratio
This work presents the fabrication of horizontally aligned PtSe 2 films using one-zone selenization of pre-deposited platinum layers. We have identified the Se : Pt ratio as a parameter controlling the charge carrier mobility in the thin films.
- 5 July 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (1) , 013101
Growth of PtSe2 few-layer films on NbN superconducting substrate
Few-layer films of transition metal dichalcogenides have emerged as promising candidates for applications in electronics. Within this group of 2D materials, platinum diselenide (PtSe2) was predicted to be a compound with one of the highest charge carrier mobility. Recently, the successful integration of group III–V nitride semiconductors with NbNx-based superconductors was reported with a semiconductor transistor grown directly on a crystalline superconductor. This opens up the possibility of combining the macroscopic quantum effects of superconductors with the electronic, photonic, and piezoelectric properties of the semiconducting material. Here, we report on the fabrication of a few-layer PtSe2 film on top of an NbN substrate layer by selenization of pre-deposited 3 nm thick Pt layers. We found the selenization parameters preserving the chemical and structural integrity of both the PtSe2 and NbN films. The PtSe2 film alignment can be tuned by varying the nitrogen flow rate through the reaction chamber. The superconducting critical temperature of NbN is only slightly reduced in the optimized samples compared to pristine NbN. The carrier mobility in PtSe2 layers determined from Hall measurements is below 1 cm2/V s.
- 5 July 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (1) , 013101
Growth of PtSe2 few-layer films on NbN superconducting substrate
Few-layer films of transition metal dichalcogenides have emerged as promising candidates for applications in electronics. Within this group of 2D materials, platinum diselenide (PtSe2) was predicted to be a compound with one of the highest charge carrier mobility. Recently, the successful integration of group III–V nitride semiconductors with NbNx-based superconductors was reported with a semiconductor transistor grown directly on a crystalline superconductor. This opens up the possibility of combining the macroscopic quantum effects of superconductors with the electronic, photonic, and piezoelectric properties of the semiconducting material. Here, we report on the fabrication of a few-layer PtSe2 film on top of an NbN substrate layer by selenization of pre-deposited 3 nm thick Pt layers. We found the selenization parameters preserving the chemical and structural integrity of both the PtSe2 and NbN films. The PtSe2 film alignment can be tuned by varying the nitrogen flow rate through the reaction chamber. The superconducting critical temperature of NbN is only slightly reduced in the optimized samples compared to pristine NbN. The carrier mobility in PtSe2 layers determined from Hall measurements is below 1 cm2/V s.