Ji Hun Yu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ji Hun Yu has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Eun-Ah Kim
Korea Institute of Materials Science, Changwon, 51508, Republic of Korea
2 shared publications - Hak-Sung Lee
Department of Materials Science and Engineering, Dong-A University, Busan 49315, Republic of Korea
2 shared publications - Woo-Jin Lee
Korea Institute of Materials Science, Changwon, 51508, Republic of Korea
2 shared publications - Yeong-Jin Woo
Korea Institute of Materials Science, Changwon, 51508, Republic of Korea
2 shared publications Byung-Kee Kim
1 shared publication- Dong-Ho Nam
Korea Institute of Materials Science, Changwon, 51508, Republic of Korea
1 shared publication
Latest Publications
- Open Access
- 30 June 2026
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 33 (3) , 184-194
Heat-Treatment-Induced Deformation Shift in LPBF-Fabricated Heterogeneous Microstructured Al–Zn–Mg–Cu Alloys
This study investigated the effect of T6 heat treatment on the tensile properties and deformation behavior of heterogeneous microstructured Al–Zn–Mg–Cu alloys fabricated by laser powder bed fusion. In the as-built state, pronounced microstructural heterogeneity, including non-uniform precipitate distributions and solute segregation concentrated in the coarse columnar grain (CCG) regions, promoted strain localization within the fine equiaxed grain (FEG) regions. This architectural imbalance produced a high ratio of hetero-deformation-induced (HDI) stress to overall flow stress. T6 heat treatment induced solute homogenization and more uniform precipitation across the matrix, together with grain growth that largely eliminated the distinct ultrafine equiaxed grain zones. These changes caused a clear hardness reversal between the FEG and CCG regions, shifting strain localization toward the CCG regions. Consequently, although the absolute magnitude of HDI stress increased with the higher flow stress, its relative contribution decreased because of the homogenized architecture. Despite reduced uniform elongation caused by early necking, overall tensile ductility improved substantially through suppression of premature intergranular cracking in the FEG regions, clarifying the relationship between microstructural evolution and deformation behavior.
- 30 June 2026
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 33 (3) , 184-194
Open AccessHeat-Treatment-Induced Deformation Shift in LPBF-Fabricated Heterogeneous Microstructured Al–Zn–Mg–Cu Alloys
This study investigated the effect of T6 heat treatment on the tensile properties and deformation behavior of heterogeneous microstructured Al–Zn–Mg–Cu alloys fabricated by laser powder bed fusion. In the as-built state, pronounced microstructural heterogeneity, including non-uniform precipitate distributions and solute segregation concentrated in the coarse columnar grain (CCG) regions, promoted strain localization within the fine equiaxed grain (FEG) regions. This architectural imbalance produced a high ratio of hetero-deformation-induced (HDI) stress to overall flow stress. T6 heat treatment induced solute homogenization and more uniform precipitation across the matrix, together with grain growth that largely eliminated the distinct ultrafine equiaxed grain zones. These changes caused a clear hardness reversal between the FEG and CCG regions, shifting strain localization toward the CCG regions. Consequently, although the absolute magnitude of HDI stress increased with the higher flow stress, its relative contribution decreased because of the homogenized architecture. Despite reduced uniform elongation caused by early necking, overall tensile ductility improved substantially through suppression of premature intergranular cracking in the FEG regions, clarifying the relationship between microstructural evolution and deformation behavior.
- 27 December 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (24) , 245105
“Non-equilibrium” grain boundaries in additively manufactured CoCrFeMnNi high-entropy alloy: Enhanced diffusion and strong segregation
Grain boundary diffusion in an additively manufactured equiatomic CoCrFeMnNi high-entropy alloy is systematically investigated at 500 K under the so-called C-type kinetic conditions when bulk diffusion is completely frozen. In the as-manufactured state, general (random) grain boundaries are found to be characterized by orders-of-magnitude enhanced diffusivities and a non-equilibrium segregation of (dominantly) Mn atoms. These features are explained in terms of a non-equilibrium state of grain boundaries after rapid solidification. The grain boundary diffusion rates are found to be almost independent on the scanning/building strategy used for the specimen’s manufacturing, despite pronounced microstructure differences. Grain boundary migration during diffusion annealing turned out to preserve the non-equilibrium state of the interfaces due to continuous consumption of the processing-induced defects by moving boundaries. Whereas the kinetic “non-equilibrium” state of the interfaces relaxes after annealing at 773 K, the non-equilibrium segregation is retained, being further accompanied by a nano-scale phase decomposition at the grain boundaries. The generality of the findings for additively manufactured materials is discussed.
- 27 December 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (24) , 245105
“Non-equilibrium” grain boundaries in additively manufactured CoCrFeMnNi high-entropy alloy: Enhanced diffusion and strong segregation
Grain boundary diffusion in an additively manufactured equiatomic CoCrFeMnNi high-entropy alloy is systematically investigated at 500 K under the so-called C-type kinetic conditions when bulk diffusion is completely frozen. In the as-manufactured state, general (random) grain boundaries are found to be characterized by orders-of-magnitude enhanced diffusivities and a non-equilibrium segregation of (dominantly) Mn atoms. These features are explained in terms of a non-equilibrium state of grain boundaries after rapid solidification. The grain boundary diffusion rates are found to be almost independent on the scanning/building strategy used for the specimen’s manufacturing, despite pronounced microstructure differences. Grain boundary migration during diffusion annealing turned out to preserve the non-equilibrium state of the interfaces due to continuous consumption of the processing-induced defects by moving boundaries. Whereas the kinetic “non-equilibrium” state of the interfaces relaxes after annealing at 773 K, the non-equilibrium segregation is retained, being further accompanied by a nano-scale phase decomposition at the grain boundaries. The generality of the findings for additively manufactured materials is discussed.
- 6 September 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (3) , 689-693
High-Efficiency Cooling System Using Additive Manufacturing
In this study, we propose a cooling structure manufactured using a specialized three-dimensional (3D) printing design method. A cooling performance test system with complex geometry that used a thermoelectric module was manufactured using metal 3D printing. A test model was constructed by applying additive manufacturing simulation and computational fluid analysis techniques, and the correlation between each element and cooling efficiency was examined. In this study, the evaluation was conducted using a thermoelectric module base cooling efficiency measurement system. The contents were compared and analyzed by predicting the manufacturing possibility and cooling efficiency, through additive manufacturing simulation and computational fluid analysis techniques, respectively.
- 6 September 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (3) , 689-693
High-Efficiency Cooling System Using Additive Manufacturing
In this study, we propose a cooling structure manufactured using a specialized three-dimensional (3D) printing design method. A cooling performance test system with complex geometry that used a thermoelectric module was manufactured using metal 3D printing. A test model was constructed by applying additive manufacturing simulation and computational fluid analysis techniques, and the correlation between each element and cooling efficiency was examined. In this study, the evaluation was conducted using a thermoelectric module base cooling efficiency measurement system. The contents were compared and analyzed by predicting the manufacturing possibility and cooling efficiency, through additive manufacturing simulation and computational fluid analysis techniques, respectively.
- 7 July 2021
- Published by SAGE Publications in Powder Metallurgy
- Vol. 65 (1) , 22-30
Effect of different WC particle shapes on laser-exposed microstructures during the directed energy deposition
Tungsten carbide (WC) in Ni-based powders is a promising candidate for laser-based additive manufacturing because WC is an extremely hard material, whereas Ni is tough and weldable. However, WC particles that are directly exposed to a laser beam can be degraded or disintegrated into tungsten and carbon as a result of excess energy. In contrast, particles in the melt pool are relatively stable. In this study, the direct energy deposition method was used with irregular and spherical WC particles in metal powder. Irregular WC particles were found to be more directly affected by laser irradiation. To explain the effects of WC particle shapes on direct laser damage, a finitepoint calculation was performed to estimate the sinking time in the melt pool. The rectangular shape particles a longer sinking time depending on the rotation angle, whereas the spherical particles sank uniformly based on the difference in the effective area of resistance.
- 7 July 2021
- Published by SAGE Publications in Powder Metallurgy
- Vol. 65 (1) , 22-30
Effect of different WC particle shapes on laser-exposed microstructures during the directed energy deposition
Tungsten carbide (WC) in Ni-based powders is a promising candidate for laser-based additive manufacturing because WC is an extremely hard material, whereas Ni is tough and weldable. However, WC particles that are directly exposed to a laser beam can be degraded or disintegrated into tungsten and carbon as a result of excess energy. In contrast, particles in the melt pool are relatively stable. In this study, the direct energy deposition method was used with irregular and spherical WC particles in metal powder. Irregular WC particles were found to be more directly affected by laser irradiation. To explain the effects of WC particle shapes on direct laser damage, a finitepoint calculation was performed to estimate the sinking time in the melt pool. The rectangular shape particles a longer sinking time depending on the rotation angle, whereas the spherical particles sank uniformly based on the difference in the effective area of resistance.
- Open Access
- 28 October 2007
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 14 (5) , 281-286
Characteristics of L10Ordered Fe50Pt50Nanoparticles Synthesized by Chemical Vapor Condensation Process
- 28 October 2007
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 14 (5) , 281-286
Open AccessCharacteristics of L10Ordered Fe50Pt50Nanoparticles Synthesized by Chemical Vapor Condensation Process