Ardiansyah Negara
Research Subjects
Ardiansyah Negara has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Shuyu Sun
School of Mathematical Sciences, Tongji University, Shanghai, China
12 shared publications - Amgad Salama
Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, SK, S7N 5A9, Canada
8 shared publications - Bilal Saad
Baker Hughes
4 shared publications Mokhtar Elgassier
Baker Hughes
4 shared publicationsMaaruf Hussain
Baker Hughes
3 shared publicationsGaurav Agrawal
Baker Hughes
2 shared publications
Latest Publications
- 24 April 2017
- Published by Society of Petroleum Engineers (SPE)
Understanding the True Stimulated Reservoir Volume in Shale Reservoirs
Successful exploitation of shale reservoirs largely depends on the effectiveness of hydraulic fracturing stimulation program. Favorable results have been attributed to intersection and reactivation of pre-existing fractures by hydraulically-induced fractures that connect the wellbore to a larger fracture surface area within the reservoir rock volume. Thus, accurate estimation of the stimulated reservoir volume (SRV) becomes critical for the reservoir performance simulation and production analysis. Micro-seismic events (MS) have been commonly used as a proxy to map out the SRV geometry, which could be erroneous because not all MS events are related to hydraulic fracture propagation. The case studies discussed here utilized a fully 3-D simulation approach to estimate the SRV. The simulation approach presented in this paper takes into account the real-time changes in the reservoir's geomechanics as a function of fluid pressures. It consists of four separate coupled modules: geomechanics, hydrodynamics, a geomechanical joint model for interfacial resolution, and an adaptive re-meshing. Reservoir stress condition, rock mechanical properties, and injected fluid pressure dictate how fracture elements could open or slide. Critical stress intensity factor was used as a fracture criterion governing the generation of new fractures or propagation of existing fractures and their directions. Simulations were run on a Cray XC-40 HPC system. The results proved the approach of using MS data as a proxy for SRV to be significantly flawed. Many of the observed stimulated natural fractures were stress related and very few that were closer to the injection field were connected. The situation is worsened in a highly laminated shale reservoir as the hydraulic fracture propagation is significantly hampered. High contrast in the in-situ stresses related strike-slip developed thereby shortens the extent of SRV. However, far field natural fractures that were not connected to hydraulic fracture were observed being stimulated. These results show the beginning of new understanding into the physical mechanisms responsible for greater disparity in stimulation results within the same shale reservoir and hence the SRV. Using the appropriate methodology, stimulation design can be controlled to optimize the responses of in-situ stresses and reservoir rock itself.
- 24 April 2017
- Published by Society of Petroleum Engineers (SPE)
Understanding the True Stimulated Reservoir Volume in Shale Reservoirs
Successful exploitation of shale reservoirs largely depends on the effectiveness of hydraulic fracturing stimulation program. Favorable results have been attributed to intersection and reactivation of pre-existing fractures by hydraulically-induced fractures that connect the wellbore to a larger fracture surface area within the reservoir rock volume. Thus, accurate estimation of the stimulated reservoir volume (SRV) becomes critical for the reservoir performance simulation and production analysis. Micro-seismic events (MS) have been commonly used as a proxy to map out the SRV geometry, which could be erroneous because not all MS events are related to hydraulic fracture propagation. The case studies discussed here utilized a fully 3-D simulation approach to estimate the SRV. The simulation approach presented in this paper takes into account the real-time changes in the reservoir's geomechanics as a function of fluid pressures. It consists of four separate coupled modules: geomechanics, hydrodynamics, a geomechanical joint model for interfacial resolution, and an adaptive re-meshing. Reservoir stress condition, rock mechanical properties, and injected fluid pressure dictate how fracture elements could open or slide. Critical stress intensity factor was used as a fracture criterion governing the generation of new fractures or propagation of existing fractures and their directions. Simulations were run on a Cray XC-40 HPC system. The results proved the approach of using MS data as a proxy for SRV to be significantly flawed. Many of the observed stimulated natural fractures were stress related and very few that were closer to the injection field were connected. The situation is worsened in a highly laminated shale reservoir as the hydraulic fracture propagation is significantly hampered. High contrast in the in-situ stresses related strike-slip developed thereby shortens the extent of SRV. However, far field natural fractures that were not connected to hydraulic fracture were observed being stimulated. These results show the beginning of new understanding into the physical mechanisms responsible for greater disparity in stimulation results within the same shale reservoir and hence the SRV. Using the appropriate methodology, stimulation design can be controlled to optimize the responses of in-situ stresses and reservoir rock itself.
- 26 September 2016
- Published by Society of Petroleum Engineers (SPE)
Hydraulic Fracture Propagation in a Highly Laminated Shale Reservoir with Complex Natural Fracture Network - Case Study Using Higher-Accuracy, Full 3-D Simulation
It is often reported that around 60% of hydraulic fracturing stages are ineffective. If so, it is likely that the design accuracy is limited by the current state of modeling and hydraulic fracture (HF) simulations. Our study presents a new alternative – a full 3-D simulation with geomechanics coupled to fluid flow. With the conventional simulation, it is extremely hard to model opening of weak lamination (Lam) and nearly impossible to generate induced horizontal fractures against the vertical overburden stress. However, horizontal fractures are routinely evident in shale reservoirs as healed fractures observed along the bedding planes. Hence, the need and importance of a true 3-D simulator that could incorporate complex geology and dynamically simulate fracture propagation by accounting for realtime changes in geomechanics and fluid pressures. Case study uses shale reservoirs, which are heavily laminated with complex natural fractures (NFs). Numerical simulations consisted of four separate coupled modules - geomechanics, hydrodynamics, a geomechanical joint model for interfacial resolution, and an adaptive remeshing module. Reservoir stress condition, rock mechanical properties, and injected fluid pressure dictate how fracture elements could open or slide. Critical stress intensity factor was used as a fracture criterion governing the generation of new fractures or propagation of existing fractures and their directions. Simulation was run on a Cray XC-40 HPC system. Typical laminated shale reservoirs anisotropic geomechanical properties obtained from literature were used to estimate a 3-D geomechanical model and NF network. HF geometry was significantly different in the presence of weak bedding, compared to when bedding was strong enough to transmit crack tip stresses across the interface. Significant amounts of fracturing fluid can be diverted into creation of horizontal fractures, even when the pressure was below the vertical stress, once bedding discontinuities are activated. Choices of NF network and Lam thickness significantly affected observed fracture propagation. The value of 3-D modeling was clearly established. This method provides more accurate solutions for stimulation design optimization, e.g., landing points, number of stages, number of clusters, spacing between stages, and stimulated reservoir volume.
- 26 September 2016
- Published by Society of Petroleum Engineers (SPE)
Hydraulic Fracture Propagation in a Highly Laminated Shale Reservoir with Complex Natural Fracture Network - Case Study Using Higher-Accuracy, Full 3-D Simulation
It is often reported that around 60% of hydraulic fracturing stages are ineffective. If so, it is likely that the design accuracy is limited by the current state of modeling and hydraulic fracture (HF) simulations. Our study presents a new alternative – a full 3-D simulation with geomechanics coupled to fluid flow. With the conventional simulation, it is extremely hard to model opening of weak lamination (Lam) and nearly impossible to generate induced horizontal fractures against the vertical overburden stress. However, horizontal fractures are routinely evident in shale reservoirs as healed fractures observed along the bedding planes. Hence, the need and importance of a true 3-D simulator that could incorporate complex geology and dynamically simulate fracture propagation by accounting for realtime changes in geomechanics and fluid pressures. Case study uses shale reservoirs, which are heavily laminated with complex natural fractures (NFs). Numerical simulations consisted of four separate coupled modules - geomechanics, hydrodynamics, a geomechanical joint model for interfacial resolution, and an adaptive remeshing module. Reservoir stress condition, rock mechanical properties, and injected fluid pressure dictate how fracture elements could open or slide. Critical stress intensity factor was used as a fracture criterion governing the generation of new fractures or propagation of existing fractures and their directions. Simulation was run on a Cray XC-40 HPC system. Typical laminated shale reservoirs anisotropic geomechanical properties obtained from literature were used to estimate a 3-D geomechanical model and NF network. HF geometry was significantly different in the presence of weak bedding, compared to when bedding was strong enough to transmit crack tip stresses across the interface. Significant amounts of fracturing fluid can be diverted into creation of horizontal fractures, even when the pressure was below the vertical stress, once bedding discontinuities are activated. Choices of NF network and Lam thickness significantly affected observed fracture propagation. The value of 3-D modeling was clearly established. This method provides more accurate solutions for stimulation design optimization, e.g., landing points, number of stages, number of clusters, spacing between stages, and stimulated reservoir volume.
- 30 May 2016
- Published by Society of Petroleum Engineers (SPE)
Numerical Simulation of Natural Gas Flow in Shale Reservoirs with Thermodynamic Equation of State: A Comparative Study
Production from unconventional reservoirs like shale gas has increased considerably in the past few years due to the advancement in twofold, i.e., horizontal drilling and hydraulic fracturing technologies. Although there has been some success in increasing gas production from shale reservoirs, unfortunately, the physicochemical processes that take place in the shale formations remain challenging and are not completely understood. Unlike conventional reservoirs, shale reservoirs are characterized by very small porosity and extremely low-permeability. Gas flow in this tight formation involves complex flow processes such as Knudsen diffusion, Klinkenberg effect, adsorption and desorption, strong rock-fluid interaction, rock deformation, etc. Furthermore, because of high pressure and high temperature reservoir conditions the gas behaves as real gas. In this work, our shale gas mathematical model is built based on the dual-porosity dual-permeability model that incorporates the complex flow processes mentioned above as well as the thermodynamic calculations. Peng-Robinson equation of state (PR-EOS) was used to calculate the gas density and compressibility factor by solving the cubic equation. In the numerical method implementation we combine the finite difference method with the experimenting pressure field approach to solve the pressure equations for the matrix and fracture systems in the dual-porosity dual-permeability model. This combination greatly reduces the computational cost when solving the large systems of pressure equations of the matrix and fracture. In this approach, a set of predefined pressure fields is generated in the solution domain such that the undetermined coefficients are calculated from these pressure fields. In the numerical example, we considered a shale reservoir with single production well. Comparison between real gas and ideal gas is studied and the result shows that considering the real gas behavior generates higher cumulative production, which implies that the gas transport capacity is higher than the ideal gas case. The result also indicates that considering real gas behavior in the model would increase the production and retard the decline curve. Therefore, it is very important to incorporate the real gas behavior into the model in order to be able to forecast the production accurately.
- 30 May 2016
- Published by Society of Petroleum Engineers (SPE)
Numerical Simulation of Natural Gas Flow in Shale Reservoirs with Thermodynamic Equation of State: A Comparative Study
Production from unconventional reservoirs like shale gas has increased considerably in the past few years due to the advancement in twofold, i.e., horizontal drilling and hydraulic fracturing technologies. Although there has been some success in increasing gas production from shale reservoirs, unfortunately, the physicochemical processes that take place in the shale formations remain challenging and are not completely understood. Unlike conventional reservoirs, shale reservoirs are characterized by very small porosity and extremely low-permeability. Gas flow in this tight formation involves complex flow processes such as Knudsen diffusion, Klinkenberg effect, adsorption and desorption, strong rock-fluid interaction, rock deformation, etc. Furthermore, because of high pressure and high temperature reservoir conditions the gas behaves as real gas. In this work, our shale gas mathematical model is built based on the dual-porosity dual-permeability model that incorporates the complex flow processes mentioned above as well as the thermodynamic calculations. Peng-Robinson equation of state (PR-EOS) was used to calculate the gas density and compressibility factor by solving the cubic equation. In the numerical method implementation we combine the finite difference method with the experimenting pressure field approach to solve the pressure equations for the matrix and fracture systems in the dual-porosity dual-permeability model. This combination greatly reduces the computational cost when solving the large systems of pressure equations of the matrix and fracture. In this approach, a set of predefined pressure fields is generated in the solution domain such that the undetermined coefficients are calculated from these pressure fields. In the numerical example, we considered a shale reservoir with single production well. Comparison between real gas and ideal gas is studied and the result shows that considering the real gas behavior generates higher cumulative production, which implies that the gas transport capacity is higher than the ideal gas case. The result also indicates that considering real gas behavior in the model would increase the production and retard the decline curve. Therefore, it is very important to incorporate the real gas behavior into the model in order to be able to forecast the production accurately.
- 25 April 2016
- Published by Society of Petroleum Engineers (SPE)
Effects of Multiple Transport Mechanisms on Shale Gas Production Behavior
Gas transport in extremely low-permeability shale formations is a multi-mechanisms-coupling process that includes gas adsorption-desorption, Knudsen diffusion, and slip flow. Incorporating these mechanisms into a unified mathematical model is crucial to obtain a more accurate shale gas production behavior. The objective of this paper is to investigate the effect of each mechanism on shale gas production behavior. We establish shale gas dual-porosity dual-permeability model that incorporates gas adsorption-desorption, Knudsen diffusion, and slip flow as well as the thermodynamics calculations. Peng-Robinson equation of state (PR-EOS) was used to calculate the gas density and compressibility factor by solving the cubic equation. In our model, gas adsorption-desorption obeys the Langmuir's isotherm as a function of reservoir pressure. Furthermore, gas viscosity changes with Knudsen number during the pressure depletion; and pore radius will increase when the adsorption gas desorbs from the pore wall. In the numerical method implementation, we combine the finite volume method with the experimenting pressure field approach to obtain the pressure distribution in the matrix and fracture systems. In this study, we investigate the effects of adsorption, Knudsen diffusion, and gas-slippage (Klinkenberg effect) on shale production behavior. We switch each mechanism on and off in the model to observe its effect on the production performance. It is observed from the results that among these mechanisms, adsorption has a great influence on gas production. Ignoring adsorbed gas would lead to a lower cumulative production. Meanwhile, the effects of Knudsen diffusion and slip flow are not as significant as adsorption. In particular for the example presented in this paper, neglecting adsorption will decrease the production nearly 80% compared to 15%-18% when Knudsen diffusion and slip flow are ignored. Knudsen diffusion and slip flow have less impact on the production because both mechanisms occurs in the matrix and contribute only to the apparent permeability, while the production is mainly determined by the fracture permeability, which is critical in determining fluid flow from the fracture system to the wellbore.
- 25 April 2016
- Published by Society of Petroleum Engineers (SPE)
Effects of Multiple Transport Mechanisms on Shale Gas Production Behavior
Gas transport in extremely low-permeability shale formations is a multi-mechanisms-coupling process that includes gas adsorption-desorption, Knudsen diffusion, and slip flow. Incorporating these mechanisms into a unified mathematical model is crucial to obtain a more accurate shale gas production behavior. The objective of this paper is to investigate the effect of each mechanism on shale gas production behavior. We establish shale gas dual-porosity dual-permeability model that incorporates gas adsorption-desorption, Knudsen diffusion, and slip flow as well as the thermodynamics calculations. Peng-Robinson equation of state (PR-EOS) was used to calculate the gas density and compressibility factor by solving the cubic equation. In our model, gas adsorption-desorption obeys the Langmuir's isotherm as a function of reservoir pressure. Furthermore, gas viscosity changes with Knudsen number during the pressure depletion; and pore radius will increase when the adsorption gas desorbs from the pore wall. In the numerical method implementation, we combine the finite volume method with the experimenting pressure field approach to obtain the pressure distribution in the matrix and fracture systems. In this study, we investigate the effects of adsorption, Knudsen diffusion, and gas-slippage (Klinkenberg effect) on shale production behavior. We switch each mechanism on and off in the model to observe its effect on the production performance. It is observed from the results that among these mechanisms, adsorption has a great influence on gas production. Ignoring adsorbed gas would lead to a lower cumulative production. Meanwhile, the effects of Knudsen diffusion and slip flow are not as significant as adsorption. In particular for the example presented in this paper, neglecting adsorption will decrease the production nearly 80% compared to 15%-18% when Knudsen diffusion and slip flow are ignored. Knudsen diffusion and slip flow have less impact on the production because both mechanisms occurs in the matrix and contribute only to the apparent permeability, while the production is mainly determined by the fracture permeability, which is critical in determining fluid flow from the fracture system to the wellbore.
- 25 April 2016
- Published by Society of Petroleum Engineers (SPE)
Enhancing Oil Recovery - Advanced Simulations for More Accurate Frac-Stages Placement
Hydraulic fracture stimulation designs are typically made of multiple stages placed along the lateral section of the well using various well completion technologies. Understanding how multiple hydraulic fractures propagate and interact with each other is essential for an effective stimulation design. The number and placement of stages are important factors for optimizing the performance of the laterals. This in turn depends on accuracy in determining fracture interference. We present advanced simulations for accurate placement of well stages. In this paper, we use a 3-D fully coupled geomechanical-fluid flow simulator which incorporates anisotropic geomechanical properties. Densely complex natural fractures and lamination are built into the model based on available core and log information. Multiple fractures are concurrently imployed to simulate real life scenarios. Fluid pressures are incrementally computed such that stress state changes dynamically with time as it happens in real field situation. Our simulations were run on Cray XC 40 HPC system. The results demonstrate that the stress shadow effects can significantly alter hydraulic fracture propagation behavior, which eventually affects the final fracture geometry. The results show that there are large differences in aperture throughout the stimulation which persists to the end of pumping. Furthermore comparison between cases with and without complex natural fractures (discrete fracture network (DFN)) and lamination was conducted with even and uneven spacing configurations. Fracture interference and spacing analysis conducted based on model with perforation frictions shows that while spacing between fractures is important, the largest impact was observed in the presence of lamination and DFN. The large differences in the way the fracture propagates highly depend on the DFN connectivity. Late-stage connection throughout the model implies later disconnection when the pressure drops. Though the computations are time intensive, we believe this is a valuable tool to use in the planning stages for asset development to increase production potential.
- 25 April 2016
- Published by Society of Petroleum Engineers (SPE)
Enhancing Oil Recovery - Advanced Simulations for More Accurate Frac-Stages Placement
Hydraulic fracture stimulation designs are typically made of multiple stages placed along the lateral section of the well using various well completion technologies. Understanding how multiple hydraulic fractures propagate and interact with each other is essential for an effective stimulation design. The number and placement of stages are important factors for optimizing the performance of the laterals. This in turn depends on accuracy in determining fracture interference. We present advanced simulations for accurate placement of well stages. In this paper, we use a 3-D fully coupled geomechanical-fluid flow simulator which incorporates anisotropic geomechanical properties. Densely complex natural fractures and lamination are built into the model based on available core and log information. Multiple fractures are concurrently imployed to simulate real life scenarios. Fluid pressures are incrementally computed such that stress state changes dynamically with time as it happens in real field situation. Our simulations were run on Cray XC 40 HPC system. The results demonstrate that the stress shadow effects can significantly alter hydraulic fracture propagation behavior, which eventually affects the final fracture geometry. The results show that there are large differences in aperture throughout the stimulation which persists to the end of pumping. Furthermore comparison between cases with and without complex natural fractures (discrete fracture network (DFN)) and lamination was conducted with even and uneven spacing configurations. Fracture interference and spacing analysis conducted based on model with perforation frictions shows that while spacing between fractures is important, the largest impact was observed in the presence of lamination and DFN. The large differences in the way the fracture propagates highly depend on the DFN connectivity. Late-stage connection throughout the model implies later disconnection when the pressure drops. Though the computations are time intensive, we believe this is a valuable tool to use in the planning stages for asset development to increase production potential.
- 25 April 2016
- Published by Society of Petroleum Engineers (SPE)
New Data-Driven Method for Predicting Formation Permeability Using Conventional Well Logs and Limited Core Data
The need for improved data accuracy, cost effectiveness and delivery time to assist in decision making has gained importance in reservoir characterization and evaluation. This paper presents a robust and inexpensive data-driven method for predicting the formation permeability profile from conventional well logs (CWLs) using the support vector regression (SVR) technique with limited core measurements. The method's feasibility and applicability are demonstrated on one field data set from a North Sea well contained a complete suite of logs and extensive core measurements. The relationship between formation permeability and well logs is often overwhelming complex and nonlinear. We use the SVR method to establish the correlation between CWLs and limited core permeability, thereafter building a permeability-prediction model as a function of selected well logs. The basic logging data used here include density, neutron, deep resistivity, compressional and Stoneley wave slowness. The permeability derived from these well logs generally compares well with the measured core permeability. Additional logging data including the clay weight fraction, thorium/potassium content, or nuclear-magnetic-resonance (NMR) bulk volume movable and irreducible are also separately integrated into those basic logs to determine if the prediction accuracy can be improved. There is no obvious difference among the predicted permeability profiles even these additional well logs are added, which could imply that the basic logs are sufficient to generate the permeability with good accuracy. SVR method could be used to improve the log interpretation accuracy as shown in this study. It can be easily adapted to predict other rock electrical, mechanical and petrophysical properties when only conventional logs and few core measurements are available. It is especially useful for unconventional reservoirs where traditional models may not be applicable and new methods are still evolving. Such new data analysis technologies could optimize our logging service and core analysis planning.
- 25 April 2016
- Published by Society of Petroleum Engineers (SPE)
New Data-Driven Method for Predicting Formation Permeability Using Conventional Well Logs and Limited Core Data
The need for improved data accuracy, cost effectiveness and delivery time to assist in decision making has gained importance in reservoir characterization and evaluation. This paper presents a robust and inexpensive data-driven method for predicting the formation permeability profile from conventional well logs (CWLs) using the support vector regression (SVR) technique with limited core measurements. The method's feasibility and applicability are demonstrated on one field data set from a North Sea well contained a complete suite of logs and extensive core measurements. The relationship between formation permeability and well logs is often overwhelming complex and nonlinear. We use the SVR method to establish the correlation between CWLs and limited core permeability, thereafter building a permeability-prediction model as a function of selected well logs. The basic logging data used here include density, neutron, deep resistivity, compressional and Stoneley wave slowness. The permeability derived from these well logs generally compares well with the measured core permeability. Additional logging data including the clay weight fraction, thorium/potassium content, or nuclear-magnetic-resonance (NMR) bulk volume movable and irreducible are also separately integrated into those basic logs to determine if the prediction accuracy can be improved. There is no obvious difference among the predicted permeability profiles even these additional well logs are added, which could imply that the basic logs are sufficient to generate the permeability with good accuracy. SVR method could be used to improve the log interpretation accuracy as shown in this study. It can be easily adapted to predict other rock electrical, mechanical and petrophysical properties when only conventional logs and few core measurements are available. It is especially useful for unconventional reservoirs where traditional models may not be applicable and new methods are still evolving. Such new data analysis technologies could optimize our logging service and core analysis planning.
- 9 November 2015
- Published by Society of Petroleum Engineers (SPE)
Numerical Simulation of Natural Gas Flow in Anisotropic Shale Reservoirs
Shale gas resources have received great attention in the last decade due to the decline of the conventional gas resources. Unlike conventional gas reservoirs, the gas flow in shale formations involves complex processes with many mechanisms such as Knudsen diffusion, slip flow (Klinkenberg effect), gas adsorption and desorption, strong rock-fluid interaction, etc. Shale formations are characterized by the tiny porosity and extremely low-permeability such that the Darcy equation may no longer be valid. Therefore, the Darcy equation needs to be revised through the permeability factor by introducing the apparent permeability. With respect to the rock formations, several studies have shown the existence of anisotropy in shale reservoirs, which is an essential feature that has been established as a consequence of the different geological processes over long period of time. Anisotropy of hydraulic properties of subsurface rock formations plays a significant role in dictating the direction of fluid flow. The direction of fluid flow is not only dependent on the direction of pressure gradient, but it also depends on the principal directions of anisotropy. Therefore, it is very important to take into consideration anisotropy when modeling gas flow in shale reservoirs. In this work, the gas flow mechanisms as mentioned earlier together with anisotropy are incorporated into the dual-porosity dual-permeability model through the full-tensor apparent permeability. We employ the multipoint flux approximation (MPFA) method to handle the full-tensor apparent permeability. We combine MPFA method with the experimenting pressure field approach, i.e., a newly developed technique that enables us to solve the global problem by breaking it into a multitude of local problems. This approach generates a set of predefined pressure fields in the solution domain in such a way that the undetermined coefficients are calculated from these pressure fields. In other words, the matrix of coefficients is constructed automatically within the solver. We ran a numerical model with different scenarios of anisotropy orientations and compared the results with the isotropic model in order to show the differences between them. We investigated the effect of anisotropy in both the matrix and fracture systems. The numerical results show anisotropy plays a crucial role in dictating the pressure fields as well as the gas flow streamlines. Furthermore, the numerical results clearly show the effects of anisotropy on the production rate and cumulative production. Incorporating anisotropy together with gas flow mechanisms in shale formations into the reservoir model is essential particularly for predicting maximum gas production from shale reservoirs.
- 9 November 2015
- Published by Society of Petroleum Engineers (SPE)
Numerical Simulation of Natural Gas Flow in Anisotropic Shale Reservoirs
Shale gas resources have received great attention in the last decade due to the decline of the conventional gas resources. Unlike conventional gas reservoirs, the gas flow in shale formations involves complex processes with many mechanisms such as Knudsen diffusion, slip flow (Klinkenberg effect), gas adsorption and desorption, strong rock-fluid interaction, etc. Shale formations are characterized by the tiny porosity and extremely low-permeability such that the Darcy equation may no longer be valid. Therefore, the Darcy equation needs to be revised through the permeability factor by introducing the apparent permeability. With respect to the rock formations, several studies have shown the existence of anisotropy in shale reservoirs, which is an essential feature that has been established as a consequence of the different geological processes over long period of time. Anisotropy of hydraulic properties of subsurface rock formations plays a significant role in dictating the direction of fluid flow. The direction of fluid flow is not only dependent on the direction of pressure gradient, but it also depends on the principal directions of anisotropy. Therefore, it is very important to take into consideration anisotropy when modeling gas flow in shale reservoirs. In this work, the gas flow mechanisms as mentioned earlier together with anisotropy are incorporated into the dual-porosity dual-permeability model through the full-tensor apparent permeability. We employ the multipoint flux approximation (MPFA) method to handle the full-tensor apparent permeability. We combine MPFA method with the experimenting pressure field approach, i.e., a newly developed technique that enables us to solve the global problem by breaking it into a multitude of local problems. This approach generates a set of predefined pressure fields in the solution domain in such a way that the undetermined coefficients are calculated from these pressure fields. In other words, the matrix of coefficients is constructed automatically within the solver. We ran a numerical model with different scenarios of anisotropy orientations and compared the results with the isotropic model in order to show the differences between them. We investigated the effect of anisotropy in both the matrix and fracture systems. The numerical results show anisotropy plays a crucial role in dictating the pressure fields as well as the gas flow streamlines. Furthermore, the numerical results clearly show the effects of anisotropy on the production rate and cumulative production. Incorporating anisotropy together with gas flow mechanisms in shale formations into the reservoir model is essential particularly for predicting maximum gas production from shale reservoirs.
- 1 October 2015
- Published by Elsevier in Journal of Contaminant Hydrology
- Vol. 181, 114-130
Numerical investigation of nanoparticles transport in anisotropic porous media
- 1 October 2015
- Published by Elsevier in Journal of Contaminant Hydrology
- Vol. 181, 114-130
Numerical investigation of nanoparticles transport in anisotropic porous media
- 1 July 2015
- Published by Elsevier in Computers & Fluids
- Vol. 114, 66-74
Multiphase flow simulation with gravity effect in anisotropic porous media using multipoint flux approximation
- 1 July 2015
- Published by Elsevier in Computers & Fluids
- Vol. 114, 66-74
Multiphase flow simulation with gravity effect in anisotropic porous media using multipoint flux approximation
- 21 April 2014
- Published by Society of Petroleum Engineers (SPE)
Density-Driven Flow Simulation in Anisotropic Porous Media: Application to CO2 Geological Sequestration
Carbon dioxide (CO2) sequestration in saline aquifers is considered as one of the most viable and promising ways to reduce CO2 concentration in the atmosphere. CO2 is injected into deep saline formations at supercritical state where its density is smaller than the hosting brine. This motivates an upward motion and eventually CO2 is trapped beneath the cap rock. The trapped CO2 slowly dissolves into the brine causing the density of the mixture to become larger than the host brine. This causes gravitational instabilities that is propagated and magnified with time. In this kind of density-driven flows, the CO2-rich brines migrate downward while the brines with low CO2 concentration move upward. With respect to the properties of the subsurface aquifers, there are instances where saline formations can possess anisotropy with respect to their hydraulic properties. Such anisotropy can have significant effect on the onset and propagation of flow instabilities. Anisotropy is predicted to be more influential in dictating the direction of the convective flow. To account for permeability anisotropy, the method of multipoint flux approximation (MPFA) in the framework of finite differences schemes is used. The MPFA method requires more point stencil than the traditional two-point flux approximation (TPFA). For example, calculation of one flux component requires 6-point stencil and 18-point stencil in 2-D and 3-D cases, respectively. As consequence, the matrix of coefficient for obtaining the pressure fields will be quite complex. Therefore, we combine the MPFA method with the experimenting pressure field technique in which the problem is reduced to solving multitude of local problems and the global matrix of coefficients is constructed automatically, which significantly reduces the complexity. We present several numerical scenarios of density-driven flow simulation in homogeneous, layered, and heterogeneous anisotropic porous media. The numerical results emphasize the significant effects of anisotropy in driving the migration of dissolved CO2 along the principal direction of anisotropy even if the porous medium is highly heterogeneous. Furthermore, the impacts of the increase of density difference between the brine and the CO2-saturated brine with respect to the onset time of convection, the CO2 flux, and the CO2 total dissolved mass are also discussed in this paper.
- 21 April 2014
- Published by Society of Petroleum Engineers (SPE)
Density-Driven Flow Simulation in Anisotropic Porous Media: Application to CO2 Geological Sequestration
Carbon dioxide (CO2) sequestration in saline aquifers is considered as one of the most viable and promising ways to reduce CO2 concentration in the atmosphere. CO2 is injected into deep saline formations at supercritical state where its density is smaller than the hosting brine. This motivates an upward motion and eventually CO2 is trapped beneath the cap rock. The trapped CO2 slowly dissolves into the brine causing the density of the mixture to become larger than the host brine. This causes gravitational instabilities that is propagated and magnified with time. In this kind of density-driven flows, the CO2-rich brines migrate downward while the brines with low CO2 concentration move upward. With respect to the properties of the subsurface aquifers, there are instances where saline formations can possess anisotropy with respect to their hydraulic properties. Such anisotropy can have significant effect on the onset and propagation of flow instabilities. Anisotropy is predicted to be more influential in dictating the direction of the convective flow. To account for permeability anisotropy, the method of multipoint flux approximation (MPFA) in the framework of finite differences schemes is used. The MPFA method requires more point stencil than the traditional two-point flux approximation (TPFA). For example, calculation of one flux component requires 6-point stencil and 18-point stencil in 2-D and 3-D cases, respectively. As consequence, the matrix of coefficient for obtaining the pressure fields will be quite complex. Therefore, we combine the MPFA method with the experimenting pressure field technique in which the problem is reduced to solving multitude of local problems and the global matrix of coefficients is constructed automatically, which significantly reduces the complexity. We present several numerical scenarios of density-driven flow simulation in homogeneous, layered, and heterogeneous anisotropic porous media. The numerical results emphasize the significant effects of anisotropy in driving the migration of dissolved CO2 along the principal direction of anisotropy even if the porous medium is highly heterogeneous. Furthermore, the impacts of the increase of density difference between the brine and the CO2-saturated brine with respect to the onset time of convection, the CO2 flux, and the CO2 total dissolved mass are also discussed in this paper.