Mondher Dhaouadi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mondher Dhaouadi has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
A. Ghazel
GRESCOM Lab, SUPCOM, University of Carthage
4 shared publicationsM. Mabrouk
GRESCOM Lab, SUPCOM, University of Carthage
4 shared publicationsA. C. de Souza
IMEP-LAHC - UMR 5130, CNRS-INPG-UJF, Minatec-3, Grenoble Cedex 1, France
1 shared publicationA.C. de Souza
IMEP-LAHC - UMR 5130, CNRS-INPG-UJF, Minatec-3, Grenoble Cedex 1, France
1 shared publication- Fethi Choubani
University of Carthage
1 shared publication S. Tedjini
ORSYS, LCIS, ESISAR-INPG, 50 rue de Laffemas, BP 54, 26902, Valence Cedex 9, France
1 shared publication
Latest Publications
- Open Access
- 27 September 2021
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2021, 1-12
A Novel 3D PILA-Type UHF RFID Tag Antenna Mountable on Metallic Objects for IoT Indoor Localization
In this paper, a novel 3D planar inverted-L antenna (PILA) Ultrahigh Frequency (UHF) Radio Frequency Identification (RFID) tag mountable on metallic surfaces is proposed for the Internet of Things (IoT) indoor localization applications. The proposed tag antenna (45mm×82mm×4mm or 0.137λ×0.25λ×0.012λ) is designed for mounting on metallic objects. The 3D PILA antenna is fabricated using a copper sheet of thickness 1mm and air as the dielectric substrate in order to minimize costs for materials and realization. In the design, T-slot has been inserted in the radiating element for tuning of the tags resonance for achieving good matching with the chip. Also, a simple equivalent circuit model has been obtained to analyze the impedance of the 3D PILA. Based on the optimized design, the fabricated prototype has been measured in the anechoic chamber. The resonant frequency of the proposed tag is stable, and it is not affected much by the metallic object. The measurement results of the antenna prototype demonstrated a reasonable agreement with the simulation results, and a read range of 3.6m was measured inside an anechoic chamber. Most importantly, in the building hallway, the proposed tag is able to achieve a maximum read distance of 18m with a transmitted power of 31.5dBm at 867MHz when placed on metal. With the 3D PILA antenna structure, the proposed antimetal tag is a suitable solution that can be integrated into an indoor localization scenario.
- 27 September 2021
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2021, 1-12
Open AccessA Novel 3D PILA-Type UHF RFID Tag Antenna Mountable on Metallic Objects for IoT Indoor Localization
In this paper, a novel 3D planar inverted-L antenna (PILA) Ultrahigh Frequency (UHF) Radio Frequency Identification (RFID) tag mountable on metallic surfaces is proposed for the Internet of Things (IoT) indoor localization applications. The proposed tag antenna (45mm×82mm×4mm or 0.137λ×0.25λ×0.012λ) is designed for mounting on metallic objects. The 3D PILA antenna is fabricated using a copper sheet of thickness 1mm and air as the dielectric substrate in order to minimize costs for materials and realization. In the design, T-slot has been inserted in the radiating element for tuning of the tags resonance for achieving good matching with the chip. Also, a simple equivalent circuit model has been obtained to analyze the impedance of the 3D PILA. Based on the optimized design, the fabricated prototype has been measured in the anechoic chamber. The resonant frequency of the proposed tag is stable, and it is not affected much by the metallic object. The measurement results of the antenna prototype demonstrated a reasonable agreement with the simulation results, and a read range of 3.6m was measured inside an anechoic chamber. Most importantly, in the building hallway, the proposed tag is able to achieve a maximum read distance of 18m with a transmitted power of 31.5dBm at 867MHz when placed on metal. With the 3D PILA antenna structure, the proposed antimetal tag is a suitable solution that can be integrated into an indoor localization scenario.
- 30 April 2015
- Published by Praise Worthy Prize in International Journal on Communications Antenna and Propagation (IRECAP)
- Vol. 5 (2) , 119
Magnetic Tag Antenna for UHF Near-field and Far-Field RFID Applications
A novel broadband magnetic Tag antenna for ultra-high frequency (UHF) near-field (NF) and far-field (FF) radio-frequency identification (RFID) applications is presented. This antenna is printed on an Rogers RT/duroid 5880 substrate with an overall size of 68 × 19.7 × 0.787 mm. The simulated bandwidth of the proposed Tag antenna is more than 100 MHz (860960MHz), which can cover the entire UHF RFID band. The proposed structure can generate a strong and uniform H-field distribution in the region around the antenna. The minimum power required to activate the Tag at 900 MHz is approximately of -12.6 dBm in the near-zone (18 cm) and 2.8 dBm in the far-zone (65 cm) in anechoic chamber. The measured read range is about 15 m when the transmission power level is 25 dBm in open environment. Measurements show that the antenna operating confirms good performance of Tag identification for near-field and far-field UHF RFID applications. Copyright © 2015 Praise Worthy Prize - All rights reserved.
- 30 April 2015
- Published by Praise Worthy Prize in International Journal on Communications Antenna and Propagation (IRECAP)
- Vol. 5 (2) , 119
Magnetic Tag Antenna for UHF Near-field and Far-Field RFID Applications
A novel broadband magnetic Tag antenna for ultra-high frequency (UHF) near-field (NF) and far-field (FF) radio-frequency identification (RFID) applications is presented. This antenna is printed on an Rogers RT/duroid 5880 substrate with an overall size of 68 × 19.7 × 0.787 mm. The simulated bandwidth of the proposed Tag antenna is more than 100 MHz (860960MHz), which can cover the entire UHF RFID band. The proposed structure can generate a strong and uniform H-field distribution in the region around the antenna. The minimum power required to activate the Tag at 900 MHz is approximately of -12.6 dBm in the near-zone (18 cm) and 2.8 dBm in the far-zone (65 cm) in anechoic chamber. The measured read range is about 15 m when the transmission power level is 25 dBm in open environment. Measurements show that the antenna operating confirms good performance of Tag identification for near-field and far-field UHF RFID applications. Copyright © 2015 Praise Worthy Prize - All rights reserved.
- 1 January 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21642958,p. 193-195
A capacitively-loaded loop antenna for UHF near-field RFID reader applications
In this work, we present a compact capacitively-loaded loop antenna for Ultra-High Frequency (UHF) near-field radio frequency identification (RFID) reader applications. The antenna structure is composed by folded-dipole loop structure with two C-arms and miniaturized to small size of 40 × 36 × 1.6 mm 3 for RFID applications. Our bandwidth measurement of antenna prototype is 10.5 MHz from 865-875.5 MHz with reflection coefficient less than 10 dB, which covers all of Europe RFID Band (865-868 MHz). Furthermore, a capacitive loading through two C-arms is created inside the loop antenna and has an effect of increasing the electrical length of the antenna structure. Therefore, the proposed antenna can be dedicated to different UHF RFID bands by varying the C-arm parameters. The measured reading capability of our antenna is up to 7 cm for near-field RFID Tag, and our measurements show this antenna is suitable for UHF near-field RFID reader applications.
- 1 January 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21642958,p. 193-195
A capacitively-loaded loop antenna for UHF near-field RFID reader applications
In this work, we present a compact capacitively-loaded loop antenna for Ultra-High Frequency (UHF) near-field radio frequency identification (RFID) reader applications. The antenna structure is composed by folded-dipole loop structure with two C-arms and miniaturized to small size of 40 × 36 × 1.6 mm 3 for RFID applications. Our bandwidth measurement of antenna prototype is 10.5 MHz from 865-875.5 MHz with reflection coefficient less than 10 dB, which covers all of Europe RFID Band (865-868 MHz). Furthermore, a capacitive loading through two C-arms is created inside the loop antenna and has an effect of increasing the electrical length of the antenna structure. Therefore, the proposed antenna can be dedicated to different UHF RFID bands by varying the C-arm parameters. The measured reading capability of our antenna is up to 7 cm for near-field RFID Tag, and our measurements show this antenna is suitable for UHF near-field RFID reader applications.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
UHF tag antenna for near-field and far-field RFID applications
In this paper, a novel broadband Tag antenna for ultra-high frequency (UHF) near-field and far-field radio-frequency identification (RFID) applications is presented. This antenna is printed on an Rogers RT/duroid 5880 substrate with an overall size of 68 × 19.7 × 0.787 mm. The simulated bandwidth of the proposed Tag antenna is more than 100 MHz (860-960 MHz), which can cover the entire UHF RFID band. The proposed structure can generate a strong and uniform H-field distribution in the region around the antenna. Measurements show that the antenna operating confirms good performance of Tag identification for near-field and far-field UHF RFID applications.
- 1 June 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
UHF tag antenna for near-field and far-field RFID applications
In this paper, a novel broadband Tag antenna for ultra-high frequency (UHF) near-field and far-field radio-frequency identification (RFID) applications is presented. This antenna is printed on an Rogers RT/duroid 5880 substrate with an overall size of 68 × 19.7 × 0.787 mm. The simulated bandwidth of the proposed Tag antenna is more than 100 MHz (860-960 MHz), which can cover the entire UHF RFID band. The proposed structure can generate a strong and uniform H-field distribution in the region around the antenna. Measurements show that the antenna operating confirms good performance of Tag identification for near-field and far-field UHF RFID applications.
- 1 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Electromagnetic analysis of UHF near-field RFID tag antenna
In this paper, the performance of Near-Field UHF RFID systems is investigated by means of electromagnetic analyses. A novel antenna is presented for ultra high frequency (UHF) near-field radio frequency identification (RFID) applications. The reactance component of tag antenna considered chip impedance (-193j) is conjugated and matched for maximum power transmission. The antenna is fabricated by using Polyester (PET) dielectric substrate with permittivity 3.2. The size of antenna is 38 × 18 × 0.5 mm. The HFSS simulator is used for optimizing the proposed antenna. The antenna Return Loss is of 14.0 dB for the worst case in the middle of UHF range, better than 31.4 dB at 900 MHz.
- 1 August 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Electromagnetic analysis of UHF near-field RFID tag antenna
In this paper, the performance of Near-Field UHF RFID systems is investigated by means of electromagnetic analyses. A novel antenna is presented for ultra high frequency (UHF) near-field radio frequency identification (RFID) applications. The reactance component of tag antenna considered chip impedance (-193j) is conjugated and matched for maximum power transmission. The antenna is fabricated by using Polyester (PET) dielectric substrate with permittivity 3.2. The size of antenna is 38 × 18 × 0.5 mm. The HFSS simulator is used for optimizing the proposed antenna. The antenna Return Loss is of 14.0 dB for the worst case in the middle of UHF range, better than 31.4 dB at 900 MHz.