Miguel A. Cavaliere
Miguel A. Cavaliere has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Marcela B. Goldschmit
Center for Industrial Research, FUDETEC, Av. Córdoba 320, Buenos Aires 1054, Argentina
5 shared publicationsM. B. Goldschmit
Center for Industrial Research
3 shared publicationsE. N. Dvorkin
Center for Industrial Research
2 shared publicationsEduardo N. Dvorkin
Center for Industrial Research, FUDETEC, Av. Cordoba 320, 1054 Buenos Aires, Argentina
2 shared publications- Eduardo N. Dvorkin
Center for Industrial Research, FUDETEC, Av. Cordoba 320, 1054 Buenos Aires, Argentina
2 shared publications - Diego A. Berazategui
Center for Industrial Research, TENARIS, Dr Simini 250, 2804 Campana, Argentina
1 shared publication
Latest Publications
- 1 January 2021
- Published by ASTM International in Materials Performance and Characterization
- Vol. 10 (1) , 420-442
Numerical Calculation of the Heat Transfer Coefficients in Multi-Thermocouple Probes by the Reconstruction Temperature Method
The numerical simulation of the heat transfer problem of the quenching process requires an accurate characterization of the heat transfer coefficient dependence on surface temperature, which is usually determined by measuring the cooling curve and applying an inverse method. In most cases, the thermocouple is located at the center of the probe (ISO 9950, Industrial Quenching Oils — Determination of Cooling Characteristics — Nickel-Alloy Probe Test Method), but, in recent years, probes with several thermocouples have been developed (e.g., Tensi test) and the process to estimate the coefficients turned out to be more complex. The proposed methodology has considered the numerical reconstruction of the temperature field of the probe using multi-thermocouple measurements, actual material properties, and heat transfer equations. The heat transfer coefficients are directly obtained from the numerically reconstructed thermal field based on the fact that its gradient at the boundaries is proportional to the heat flux transferred. It is important to remark that neither parameter optimization nor curve fitting is needed.
- 1 January 2021
- Published by ASTM International in Materials Performance and Characterization
- Vol. 10 (1) , 420-442
Numerical Calculation of the Heat Transfer Coefficients in Multi-Thermocouple Probes by the Reconstruction Temperature Method
The numerical simulation of the heat transfer problem of the quenching process requires an accurate characterization of the heat transfer coefficient dependence on surface temperature, which is usually determined by measuring the cooling curve and applying an inverse method. In most cases, the thermocouple is located at the center of the probe (ISO 9950, Industrial Quenching Oils — Determination of Cooling Characteristics — Nickel-Alloy Probe Test Method), but, in recent years, probes with several thermocouples have been developed (e.g., Tensi test) and the process to estimate the coefficients turned out to be more complex. The proposed methodology has considered the numerical reconstruction of the temperature field of the probe using multi-thermocouple measurements, actual material properties, and heat transfer equations. The heat transfer coefficients are directly obtained from the numerically reconstructed thermal field based on the fact that its gradient at the boundaries is proportional to the heat flux transferred. It is important to remark that neither parameter optimization nor curve fitting is needed.
- 19 September 2005
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 65 (7) , 1113-1144
On the modelling of complex 3D bulk metal forming processes via the pseudo‐concentrations technique. Application to the simulation of the Mannesmann piercing process
The modelling of complex 3D metal forming processes using the flow formulation, implemented via the pseudo‐concentrations technique, requires the development of robust computational strategies for dealing with the velocity and pseudo‐concentration boundary conditions in the zone where the blank–tools contact is developed. A new algorithm, designed to fulfil those requirements, is presented in this paper.The Mannesmann piercing process is a metal forming operation used in industry for manufacturing metal seamless pipes. The results of the Mannesmann process finite element simulation are particularly dependent on the accuracy and stability of the algorithm used to describe the contact boundary conditions between the forming tools and the blank. The validation of the finite element model is performed by comparing the numerical predictions obtained using the new algorithm with the results of industrial tests. Copyright © 2005 John Wiley & Sons, Ltd.
- 19 September 2005
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 65 (7) , 1113-1144
On the modelling of complex 3D bulk metal forming processes via the pseudo‐concentrations technique. Application to the simulation of the Mannesmann piercing process
The modelling of complex 3D metal forming processes using the flow formulation, implemented via the pseudo‐concentrations technique, requires the development of robust computational strategies for dealing with the velocity and pseudo‐concentration boundary conditions in the zone where the blank–tools contact is developed. A new algorithm, designed to fulfil those requirements, is presented in this paper.The Mannesmann piercing process is a metal forming operation used in industry for manufacturing metal seamless pipes. The results of the Mannesmann process finite element simulation are particularly dependent on the accuracy and stability of the algorithm used to describe the contact boundary conditions between the forming tools and the blank. The validation of the finite element model is performed by comparing the numerical predictions obtained using the new algorithm with the results of industrial tests. Copyright © 2005 John Wiley & Sons, Ltd.
- 31 May 2003
- Published by Elsevier in Computers & Structures
- Vol. 81 (8-11) , 559-573
Finite element models in the steel industry: Part I: Simulation of flat product manufacturing processes
- 31 May 2003
- Published by Elsevier in Computers & Structures
- Vol. 81 (8-11) , 559-573
Finite element models in the steel industry: Part I: Simulation of flat product manufacturing processes
- 27 September 2001
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 52 (12) , 1411-1430
Finite element simulation of the steel plates hot rolling process
In this paper we discuss our finite element procedure for simulating the hot rolling of flat steel products. We couple an Eulerian rigid‐viscoplastic model of the steel plates deformation to a Lagrangian elastic model of the rolls deformation. This latter model incorporates the bending deformation of the work rolls supported by the back‐up rolls and the flattening of the contact areas (Hertz problem) via an enhanced beam model.The finite element model is validated comparing its predictions with actual industrial measurements and then it is used to analyse different rolling set‐ups. Copyright © 2001 John Wiley & Sons, Ltd.
- 27 September 2001
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 52 (12) , 1411-1430
Finite element simulation of the steel plates hot rolling process
In this paper we discuss our finite element procedure for simulating the hot rolling of flat steel products. We couple an Eulerian rigid‐viscoplastic model of the steel plates deformation to a Lagrangian elastic model of the rolls deformation. This latter model incorporates the bending deformation of the work rolls supported by the back‐up rolls and the flattening of the contact areas (Hertz problem) via an enhanced beam model.The finite element model is validated comparing its predictions with actual industrial measurements and then it is used to analyse different rolling set‐ups. Copyright © 2001 John Wiley & Sons, Ltd.
- 1 September 2001
- Published by Elsevier in Computers & Structures
- Vol. 79 (22-25) , 2075-2089
Finite element analysis of steel rolling processes
- 1 September 2001
- Published by Elsevier in Computers & Structures
- Vol. 79 (22-25) , 2075-2089
Finite element analysis of steel rolling processes
- 1 June 1997
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 68 (1) , 99-107
2D finite element parametric studies of the flat-rolling process
- 1 June 1997
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 68 (1) , 99-107
2D finite element parametric studies of the flat-rolling process
- 1 June 1997
- Published by Emerald Publishing in Engineering Computations
- Vol. 14 (4) , 441-455
An iterative (k‐L)‐predictor/ε‐corrector algorithm for solving (k‐ε) turbulent models
The finite element solution of turbulent flows using a (k‐ε) turbulence model usually presents severe numerical difficulties. Develops an iterative (k‐L)‐predictor/ε‐corrector algorithm for overcoming this and solving the (k‐ε) turbulent models. The iterative scheme achieves convergence in L (length scale) which is proportional to (k1.5/ε). Numerical results indicate that the developed iterative algorithm is very robust.
- 1 June 1997
- Published by Emerald Publishing in Engineering Computations
- Vol. 14 (4) , 441-455
An iterative (k‐L)‐predictor/ε‐corrector algorithm for solving (k‐ε) turbulent models
The finite element solution of turbulent flows using a (k‐ε) turbulence model usually presents severe numerical difficulties. Develops an iterative (k‐L)‐predictor/ε‐corrector algorithm for overcoming this and solving the (k‐ε) turbulent models. The iterative scheme achieves convergence in L (length scale) which is proportional to (k1.5/ε). Numerical results indicate that the developed iterative algorithm is very robust.
- 1 December 1995
- Published by Springer Nature in Computational Mechanics
- Vol. 17 (1-2) , 2-9
A three field element via Augmented Lagrangian for modelling bulk metal forming processes
- 1 December 1995
- Published by Springer Nature in Computational Mechanics
- Vol. 17 (1-2) , 2-9
A three field element via Augmented Lagrangian for modelling bulk metal forming processes
- 1 December 1995
- Published by Springer Nature in Computational Mechanics
- Vol. 17 (1-2) , 1-9
A three field element via Augmented Lagrangian for modelling bulk metal forming processes
- 1 December 1995
- Published by Springer Nature in Computational Mechanics
- Vol. 17 (1-2) , 1-9
A three field element via Augmented Lagrangian for modelling bulk metal forming processes
- 1 November 1995
- Published by ASME International in Applied Mechanics Reviews
- Vol. 48 (11S) , S211-S215
Modeling of Turbulent Recirculating Flows Via an Iterative (k-L)-Predictor / (ε)-Corrector Scheme
A new iterative (k-L)-predictor / (ε)-corrector algorithm is used in the modeling of turbulent flows. The application of this model to recirculating flows is evaluated. The presented numerical results indicate that the developed iterative algorithm is very robust and does not require a case by case tuning.
- 1 November 1995
- Published by ASME International in Applied Mechanics Reviews
- Vol. 48 (11S) , S211-S215
Modeling of Turbulent Recirculating Flows Via an Iterative (k-L)-Predictor / (ε)-Corrector Scheme
A new iterative (k-L)-predictor / (ε)-corrector algorithm is used in the modeling of turbulent flows. The application of this model to recirculating flows is evaluated. The presented numerical results indicate that the developed iterative algorithm is very robust and does not require a case by case tuning.