BSBenjamin Steinrücken

Benjamin Steinrücken

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Benjamin Steinrücken has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Development of a Pressurized Test Rig for Reversible Solid-Oxide Short Stacks

    by Sören Ohmstedt, Benjamin Steinrücken, Florian Kerscher, Hartmut Spliethoff

    Reversible solid oxide cells (rSOCs) offer a highly efficient and versatile platform for energy conversion, enabling both power generation and electrolysis to support the switch from base load fossil energy conversion to intermittent renewable technologies. An additional key advantage of solid oxide technology is its ability to perform co-electrolysis of H₂O and CO₂, directly producing syngas—a crucial intermediate for Power-to-X (PtX) chemical conversion processes. This makes rSOCs particularly well-suited for integration with PtX technologies, which often operate at elevated pressures. [1] Pressurization has demonstrated promising effects in both simulations and single-cell experiments, primarily by reducing concentration overpotentials. The partial pressure increase generally results in an increased Nernst-Voltage. In the fuel cell mode this leads to higher cell voltages at a given current densities compared to atmospheric operation. The power output is increased for the same fuel flow, improving efficiency and power density in SOFC operation while reducing operational costs due to better efficiencies and investment costs due to higher power densities. [2] In electrolysis mode, pressurization is disadvantageous at low current densities. A higher voltage is needed for a given molar product flow compared to atmospheric operation. This effect is mitigated at higher current densities due to reduced concentration overpotentials. Notably, at thermoneutral voltage—a favorable operating point for electrolysis—the required voltage can fall below atmospheric levels. [3] Furthermore, the integration of pressurized SOECs with PtX processes and hydrogen storage applications can enhance overall system efficiency by reducing the energy required for post-electrolysis gas compression. Despite the significance of pressurization, comprehensive experimental studies on stack-level under reversible operation conditions remain scarce. This study presents a novel test rig designed for the characterization and degradation analysis of solid oxide short stacks. Developed at the Technical University of Munich, the rig supports multiple gas feedstocks and accommodates short stacks with up to 15 cells and outer dimensions of 190 × 230 mm. It enables operation from atmospheric pressure up to 11 bara and allows flexible switching between electrolysis and fuel cell modes using either an electrical power source or load. The system includes an electrical heating unit capable of reaching 950 °C and maintains a pressure differential between the fuel and air sides below 50 mbar. A comprehensive set of measurement devices records absolute and differential pressures, temperature distributions along the cells, and outlet gas compositions. Additionally, electrochemical impedance spectroscopy (EIS) measurements at both cell and stack levels facilitate in-depth analysis of internal rSOC processes. The test rig is also designed to enable continuous intermediate-term experiments, allowing for operational investigations over approximately 1000 hours. This capability is essential for studying long-term performance, degradation mechanisms, and the impact of pressurization on stack stability under realistic operating conditions. These extended tests provide valuable insights into the durability and reliability of rSOCs, further supporting their integration into industrial-scale PtX applications. [1] S. Araya, X. Cui, N. Li, V. Liso, S. Sahlin, “Power-to-X: Technology overview, possibilities and challenges,” AAU, 2022. [2] M. Riedel, M.P. Heddrich, A. Ansar, Q.Fank, L. blum, K.A. Friedrich, „Pressurized operation of solid oxide electrolysis stacks: An experimental comparison of the performance of 10-layer stacks with fuel electrode and electrolyte supported cell concepts,” J. Power Sources, vol. 475, Nov 2020 [3] Y. Du, Y. Qin, G. Zhang, Y. Yin, K. Jiao, Q. Du, „Modelling of effect of pressure on co-electrolysis in water and carbon dioxide in solid oxide electrolysis cell,” Int. J. Hydrogen Energy, vol. 44, pp 3456-3469, Feb 2019.

  • Investigation of the Stack Uniformity in an Internal Reforming Solid Oxide Fuel Cell (SOFC) Stack

    by Chen Lin, Florian Kerscher, Benjamin Steinrücken, Hartmut Spliethoff

    As a promising energy conversion technology, solid oxide fuel cells (SOFCs) are evolving toward higher power output to meet a broader range of applications. However, scaling up SOFC stacks by increasing the number of cells and enlarging the active area introduces challenges related to stack uniformity. Key issues include increased temperature gradients and significant cell-to-cell voltage variations, both of which can impact overall performance and durability. In this study, a methane-rich internal reforming SOFC stack was developed and analyzed using computational fluid dynamics (CFD). The model incorporates both methane steam reforming (MSR) and water-gas shift (WGS) reactions to accurately represent the internal reforming process. The uniformity of SOFC stacks with different manifold configurations was compared, and the results indicated that a 3-inlet & 2-outlet design exhibited the best stack uniformity. Furthermore, it was found that the manifold inlet size plays a crucial role in determining cell-to-cell parameter uniformity. The findings of this study provide valuable theoretical guidance for the design and practical implementation of SOFC stacks. By improving cell-to-cell uniformity, the optimized manifold design contributes to enhanced performance and greater reliability in large-scale applications.

  • Experimental Study of the Interaction between Ni-8YSZ Support Material and Model Tar-Containing Syngas from Biomass Gasification

    by Benjamin Steinrücken, Florian Kerscher, Cosmo Damian Taniguchi, Sören Ohmstedt, Hartmut Spliethoff

    The decarbonization of the chemical industry requires a carbon-neutral production of bulk chemicals. The feedstock (syngas) for synthesising such bulk chemicals can be produced by gasifying biomass or residues. This syngas produced by biomass gasification typically has a H 2 /CO ratio below 1. The synthesis requires an increased H 2 /CO ratio, e.g. Fischer-Tropsch a ratio of 2 - 2.1. Hydrogen addition and a water gas shift reactor are needed to meet this requirement and ensure a high carbon efficiency. Integrating an inline co-electrolysis into the process can be more efficient than parallel water electrolysis and additionally replace the water-gas-shift reactor. The oxygen-blown entrained flow gasification technology has been shown to produce syngas at high purity and conversion rates. This technology additionally enables a simple upscaling of the process. However, the efficiency and stability of such inline integration of the solid oxide cell (SOC) can be compromised by contaminants produced by the gasification process. Removing particles, sulphur and chlorine species at elevated temperatures (e.g. 350 °C) is mandatory to stabilise the SOC and downstream synthesis. However, for the fourth class of contaminants – complex aromatic hydrocarbons called tars - different impacts on the SOC operation were observed. Either the tars produced by the gasifier can harmlessly be reformed inside the SOC, or the tars cause carbon depositions, structural degradation and/or electrochemical degradation. The prediction of the tar’s impact on the SOC is additionally complicated by different tars exhibiting different behaviors. Therefore, a detailed comparison of multiple model tars at a relevant concentration for the entrained flow gasification is required. The main degradation mechanisms are structural degradation by carbon depositions or nickel dusting and a degradation of the catalytic activity and electrochemical performance. This work uses Ni-8YSZ commercial substrate material to investigate and compare the tar-induced degradation of multiple individual tar species. The circular 20 mm diameter substrate samples are operated at 700 °C under internal reforming conditions at a 50/25/10/10/5 % H 2 O/H 2 /CO 2 /CO/CH 4 gas mixture. The individual model tars are dossed at a concentration of 0.5 g/Nm³ (dry basis). In single-cell and short-stack studies, electrochemical degradation was observed to happen in parallel to the degradation of the chemical activity of the cell. This observation is utilised in the test rig: If no degradation of the catalytic performance of the substrate layer occurs, no electrochemical degradation of a full cell is expected. This simplifies the study and enables a fast screening of the different tars. The chemical activity of the substrate material is monitored via the steam methane reforming reaction with an off-gas analysis. Scanning electron microscopy is used for post-mortem analysis of the substrate sample. The study compares the investigated tars, exploring the influence of their functional groups on the degradation process.

  • Open Access

    Technical evaluation and life-cycle assessment of solid oxide co-electrolysis integration in biomass-to-liquid processes for sustainable aviation fuel production

    by Marcel Dossow, Benjamin Steinrücken, Maximilian Schmid, Daniel Cenk Rosenfeld, Sebastian Fendt, Florian Kerscher, Hartmut Spliethoff


  • Open Access

    Phase stability, redox-behavior and carbon-tolerance of Sr1−x(Ti0.3Fe0.7−yNiy)O3−δ with exsolved nanoparticles

    by Alexander Schwiers, Daniel Röhrer, Christian Lenser, Benjamin Steinrücken, Doris Sebold, Hartmut Spliethoff, Olivier Guillon, Norbert H. Menzler

    Ni-exsolution from perovskites has gained significant attention in the area of electrode materials for fuel and electrolysis cells due to their potential for high catalytic activity, tolerance to degradation, improved redox-cycling stability, and regeneration of the nanoparticles. We investigated the exsolution behavior and phase stability of bulk Sr1-x(Ti0.3Fe0.7-yNiy)O3-δ ceramics at various temperatures and atmospheres. To assess its tolerance to carbon deposition, Sr1-x(Ti0.3Fe0.7-yNiy)O3-δ was compared with commonly used Ni-YSZ materials in the presence of tar-containing biogas. Nanoparticle exsolution was observed in the entire investigated temperature range of 710–900 °C. Above a reduction temperature of 740 °C, Sr1-x(Ti0.3Fe0.7-yNiy)O3-δ partially transforms to a Ruddlesden-Popper phase, while reverting back to the perovskite phase during reoxidation. This phase transition resulted in material expansion and the formation of cracks. Moreover, exposure of reduced Sr1-x(Ti0.3Fe0.7-yNiy)O3-δ to ambient air or H2O led to the formation of secondary phases and fragmentation of sintered pellets. Remarkably, when compared to Ni-YSZ, these materials exhibited no degradation in terms of carbon deposition or Ni dusting after exposure to tar-containing biogas.


  • Open Access

    Experimental Investigation of Naphthalene Induced Degradation of Reversible Solid Oxide Cells Operated on Bio-Syngas

    by B. Steinrücken, S. Herrmann, F. Kerscher, K. Feigl, A. Schwiers, C. Lenser, N. H. Menzler, O. Guillon, H. Spliethoff

    The influence of the operational conditions and the electrode material on the degradation induced by the model tar naphthalene on 10 × 10 cm2 fuel-electrode supported solid oxide cells operated on artificial bio-syngas under internal reforming conditions is experimentally investigated. Two different fuel electrodes are investigated based on yttrium-stabilized zirconia (YSZ) and gadolinium-doped ceria (GDC). A parameter study of the operational temperature and the operation mode (fuel cell or electrolysis mode) is conducted with the YSZ-based fuel electrode to quantify the effects on the cell degradation. The fuel off-gas composition and electrochemical impedance spectra are used to characterize the cell prior to the experiment and monitor its performance during the poisoning process. The influence of the tar on the Ni-YSZ electrode cell is investigated for an operation at 700 °C and 800 °C in fuel cell mode, and an operation at 700 °C in electrolysis mode. The experiment at 700 °C is repeated with the Ni-GDC electrode cell. At the increased operational temperature, the Ni-YSZ cell is more robust but carbon depositions occur. The voltage degradation during electrolysis operation increases significantly compared to fuel cell operation. The Ni-GDC electrode does not show an increased robustness compared to the Ni-YSZ electrode.


  • Experimental Investigation of Naphthalene Induced Degradation of Reversible Solid Oxide Cells Operated on Bio-Syngas

    by Benjamin Steinrücken, Stephan Herrmann, Karsten Feigl, Alexander Schwiers, Christian Lenser, Norbert H. Menzler, Hartmut Spliethoff

    To tackle the demand for renewable alternatives to natural gas and for renewable energy, the operation of reversible solid oxide cells (rSOC) with syngas from biomass gasification is a highly efficient option. The fuel gas, produced close to carbon neutrality by the gasifier can be either converted to electrical power via the fuel cell mode or energetically upgraded via the electrolysis mode for e.g. utilization in chemical synthesis processes. Due to the reversible operation, a system based on an rSOC perfectly fits in an energy system with a high share of fluctuating renewable energy. However, impurities in fuel gas result in a fast degradation of the cells performance. This requires a comprehensive syngas cleaning to enable a stable operation of the cell. For the design of such a system, a deeper knowledge about the degradation processes is required. Especially the influence of tars is part of an ongoing research due to their ambivalent role as fuel and poison. In this work, the model tar Naphthalene is used to experimentally investigate the influence of polycyclic aromatic components on the performance of 10 x 10 cm² fuel-electrode supported solid oxide cells operated at artificial bio-syngas under internal reforming conditions. Two different fuel electrodes based on yttrium-stabilized zirconia (YSZ) and gadolinium-doped ceria (GDC) are investigated. A parameter study of the operational temperature and the operation mode is conducted with the YSZ based fuel electrode to quantify the effect on the degradation. The influence of the set-up is investigated by an experiment without the cell. The cell temperature distribution, the pressure drop and the fuel off-gas composition is measured. Electrochemical impedance spectroscopy is used to characterize the cell prior to the experiment and to monitor its performance during the poisoning and regeneration process. The measurements are interpreted via the distribution of relaxation times. The electrolysis mode is observed to be more vulnerable towards poisoning with the tar than the fuel cell mode. The poisoning effects, whether it is a performance degradation or carbon deposition, are not only dependent on the tar but also on the operational conditions. The GDC fuel-electrode did not show the expected high robustness. The investigated cells are prototypes of an ongoing development process; hence a more detailed investigation is required when the development is finished.

  • Recent Developments of the International Future Lab of Hydrogen Economy: Using Artificial Intelligence (AI) Based Machine Learning (ML) in r-SOC Development

    by Murat Peksen, Benjamin Steinrücken, Hartmut Spliethoff

    The International Future Laboratory for Hydrogen Economy at the Technical University of Munich (TUM) has established a research-network model researching in the field of electrically assisted gasification, reversible solid oxide cells, and biocatalytic synthesis of hydrogen. Using experimental and numerical data, the current study elucidates the progress on reversible solid oxide cell technologies. Advanced artificial intelligence (AI)-based machine learning approaches are utilized to evaluate and optimize SOC-relevant processes. The SOC research is giving particular attention to the integrated approach of traditional numerical methods such as CFD and accelerated modern AI methods. The complex thermochemistry of syngas-containing auxiliary components has been assessed using experimentally validated numerical models. The approach is utilized to create data for the successful construction and training of AI-based machine-learning models. Multi-regression studies shed light on the interactions between process variables to improve and prepare SOC-ready fuel which is essential for successful operation. A recently developed ML model is effectively employed to forecast and optimize the reforming procedures with different fuel constellations including oxygen-containing syngas compositions. Consequently, the results contribute to better knowledge and qualitative benefits of the preparation of high-quality, pure syngas, improved fuel utilisation furthering sustainable research and r-SOC operation in a safe, consistent manner. Hence, the availability of valuable information early in the process is achieved. Moreover, the approach reduced prohibitive experiments contributing to the sustainable use of resources.

  • Experimental Investigation of Naphthalene Induced Degradation of Reversible Solid Oxide Cells Operated on Bio-Syngas

    by Benjamin Steinrücken, Stephan Herrmann, Karsten Feigl, Alexander Schwiers, Christian Lenser, Norbert H. Menzler, Hartmut Spliethoff

    The model tar Naphthalene is used to experimentally investigate the influence of polycyclic aromatic components on the performance of 10 x 10 cm² fuel-electrode supported solid oxide cells operated at artificial bio-syngas under internal reforming conditions. Two different fuel electrodes based on yttrium-stabilized zirconia (YSZ) and gadolinium-doped ceria (GDC) are investigated. A parameter study of the operational temperature and the operation mode is conducted with the YSZ based fuel electrode to quantify the effect on the degradation. The influence of the set-up is investigated by an experiment without the cell. The fuel off-gas composition as well as electrochemical impedance spectroscopy is used to characterize the cell prior to the experiment and to monitor its performance during the poisoning and regeneration process. The measurements are interpreted via the distribution of relaxation times.

  • Recent Developments of the International Future Lab of Hydrogen Economy: Using Artificial Intelligence (AI) Based Machine Learning (ML) in r-SOC Development

    by Murat Peksen, Benjamin Steinrücken, Hartmut Spliethoff

    Current r-SOC research places special emphasis on the integrated approach of traditional numerical methods like CFD and accelerated AI methods. Using experimentally validated numerical models, the complex thermochemistry of auxiliary components containing syngas was evaluated. This method is used to generate data for the successful development and training of AI-based machine-learning models. Analyses shed light on the interactions between process variables in order to improve and prepare SOC-ready fuel, which is crucial for operation success. A recently developed ML model is utilised effectively to forecast and optimise reforming processes with various fuel constellations, including syngas compositions containing oxygen. Consequently, the results contribute to a greater understanding and qualitative benefits of preparing high-quality, pure syngas, improved fuel utilisation advancing sustainable research, and safe, consistent r-SOC operation. Consequently, early availability of valuable information is achieved. In addition, the strategy reduced prohibitive experiments, which contributed to the sustainable utilisation of resources.