Aurelien Sikora
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aurelien Sikora has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Marc Faucon
ALPhANOV, Institut d’optique d’Aquitaine, 33400 Talence, France
4 shared publications - Girolamo Mincuzzi
ALPhANOV (France)
3 shared publications - Rainer Kling
Berner Fachhochschule (Switzerland)
3 shared publications - Laura Gemini
ALPhANOV
2 shared publications Bruno Chassagne
ALPhANOV (France)
1 shared publicationG. Mincuzzi
Aquitaine Inst Opt, Rue F Mitterrand, F-33400 Talence, France
1 shared publication
Latest Publications
- Open Access
Benefits of Femtosecond Laser 40 MHz Burst Mode for Li-Ion Battery Electrode Structuring
In Li-ion batteries, ion diffusion kinetics represent a limitation to combine high capacity and a fast charging rate. To bypass this, textured electrodes have been demonstrated to increase the active surface, decrease the material tortuosity and accelerate the electrolyte wetting. Amongst the structuring technologies, ultrashort pulse laser processing may represent the key option enabling, at the same time, high precision, negligible material deterioration and high throughput. Here, we report a study on the structuring of electrodes with both holes and grooves reaching the metallic collector. Electrochemical models emphasize the importance of hole and line dimensions for the performances of the cell. We demonstrate that we can control the hole and line width by adjusting the applied fluence and the repetition rate. In addition, results show that it is possible to drill 65 µm-deep and ~15 µm-wide holes in nearly 100 µs resulting in up to 10,000 holes/s. To further reduce the takt time, bursts of 40 MHz pulses were also investigated. We show that bursts can reduce the takt time by a factor that increases with the average power and the burst length. Moreover, at comparable fluence, we show that bursts can shorten the process more than theoretically expected.
Open AccessBenefits of Femtosecond Laser 40 MHz Burst Mode for Li-Ion Battery Electrode Structuring
In Li-ion batteries, ion diffusion kinetics represent a limitation to combine high capacity and a fast charging rate. To bypass this, textured electrodes have been demonstrated to increase the active surface, decrease the material tortuosity and accelerate the electrolyte wetting. Amongst the structuring technologies, ultrashort pulse laser processing may represent the key option enabling, at the same time, high precision, negligible material deterioration and high throughput. Here, we report a study on the structuring of electrodes with both holes and grooves reaching the metallic collector. Electrochemical models emphasize the importance of hole and line dimensions for the performances of the cell. We demonstrate that we can control the hole and line width by adjusting the applied fluence and the repetition rate. In addition, results show that it is possible to drill 65 µm-deep and ~15 µm-wide holes in nearly 100 µs resulting in up to 10,000 holes/s. To further reduce the takt time, bursts of 40 MHz pulses were also investigated. We show that bursts can reduce the takt time by a factor that increases with the average power and the burst length. Moreover, at comparable fluence, we show that bursts can shorten the process more than theoretically expected.
- 22 July 2023
- Published by Elsevier in Applied Surface Science
- Vol. 638
Fabrication of multisymmetrical hierarchical structures by direct laser interference patterning with 2 beams
- 22 July 2023
- Published by Elsevier in Applied Surface Science
- Vol. 638
Fabrication of multisymmetrical hierarchical structures by direct laser interference patterning with 2 beams
- 17 March 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC12408, PC124080C-19
Surface functionalisation of transparent materials: high-throughputs meet high resolutions
The nature of transparent materials makes their laser-based functionalisation more complex, highly material dependant and often characterised by process throughputs too low to be considered competitive for an industrial uptake. In this frame, direct laser interference patterning (DLIP) appears to be the right compromise to achieve 100s-nm surface features while running at competitive throughputs. A state-of-the-art DLIP processing setup is employed to shape the 100s-nm nanostructure features to obtain highly homogeneous morphologies in different regimes of interaction on polycarbonate, fused silica and sapphire, including a DLIP-tailored f-theta lens connected to a 30-mm aperture high-speed galvanometric scanning head.
- 17 March 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. PC12408, PC124080C-19
Surface functionalisation of transparent materials: high-throughputs meet high resolutions
The nature of transparent materials makes their laser-based functionalisation more complex, highly material dependant and often characterised by process throughputs too low to be considered competitive for an industrial uptake. In this frame, direct laser interference patterning (DLIP) appears to be the right compromise to achieve 100s-nm surface features while running at competitive throughputs. A state-of-the-art DLIP processing setup is employed to shape the 100s-nm nanostructure features to obtain highly homogeneous morphologies in different regimes of interaction on polycarbonate, fused silica and sapphire, including a DLIP-tailored f-theta lens connected to a 30-mm aperture high-speed galvanometric scanning head.
- 5 March 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11674, 116740W-28
Impact of beam profile on surface texturing
Several beam shaping strategies have been proposed as an effective approach to fully exploit the average power delivered by the last generation of high power, industrial, femtosecond laser whilst avoiding unwanted thermal effects. Nevertheless, in the case of surface texturing, the effect of the profile modifications on the surface morphology has been barely investigated. The objective of our study is to understand more deeply how the beam profile features will impact the surface evolution. By tailoring the beam profile, we want to understand if it is possible to increase the process throughput. A comprehensive study has been carried out with a 35 W, 2MHz, femtosecond industrial laser. The impact of the beam intensity profile on texturing of metallic surface has been investigated. We systematically studied how the beam size (from 10 μm to few hundreds of microns) impacts the generation and evolution of Laser Induced Periodic Surface Structures (LIPSS) on Stainless Steel surface. SEM analysis has been carried out for all the generated morphologies.
- 5 March 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11674, 116740W-28
Impact of beam profile on surface texturing
Several beam shaping strategies have been proposed as an effective approach to fully exploit the average power delivered by the last generation of high power, industrial, femtosecond laser whilst avoiding unwanted thermal effects. Nevertheless, in the case of surface texturing, the effect of the profile modifications on the surface morphology has been barely investigated. The objective of our study is to understand more deeply how the beam profile features will impact the surface evolution. By tailoring the beam profile, we want to understand if it is possible to increase the process throughput. A comprehensive study has been carried out with a 35 W, 2MHz, femtosecond industrial laser. The impact of the beam intensity profile on texturing of metallic surface has been investigated. We systematically studied how the beam size (from 10 μm to few hundreds of microns) impacts the generation and evolution of Laser Induced Periodic Surface Structures (LIPSS) on Stainless Steel surface. SEM analysis has been carried out for all the generated morphologies.