Baoxin Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Baoxin Liu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Pei-Shan Chen
Kyushu Institute of Technology
10 shared publications - Xiangdong Yan
Department of Civil and Environmental Engineering, University of Pittsburgh, Pittsburgh, Pa
8 shared publications - Jialiang Jin
State Key Laboratory of Disaster Reduction in Civil Engineering, Tongji University, Shanghai 200092, China
6 shared publications - Bashar Sami Mohammed
Civil and Environmental Engineering Department, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Malaysia
3 shared publications - Amin Al-Fakih
Department of Civil and Environmental Engineering, King Fahd University of Petroleum and Minerals, Dhahran, Saudi Arabia
1 shared publication - Hui-Bin Ge
Zhejiang University
1 shared publication
Latest Publications
- 6 February 2024
- Published by Springer Nature
- p. 281-289
The Approximate Equation for Global Buckling Load of Grid Shell Domes
- 6 February 2024
- Published by Springer Nature
- p. 281-289
The Approximate Equation for Global Buckling Load of Grid Shell Domes
- 4 January 2024
- Published by Springer Nature
- p. 209-221
Approximate Equation for Estimating Global Buckling Load of Single-Layer Cylindrical Space Frames
- 4 January 2024
- Published by Springer Nature
- p. 209-221
Approximate Equation for Estimating Global Buckling Load of Single-Layer Cylindrical Space Frames
- 4 January 2024
- Published by Springer Nature
- p. 235-254
Dynamic Properties and Seismic Performance of 1.5-Layer Space Frames with Lap-Units whilst Considering Vibration of Lower Joints
- 4 January 2024
- Published by Springer Nature
- p. 235-254
Dynamic Properties and Seismic Performance of 1.5-Layer Space Frames with Lap-Units whilst Considering Vibration of Lower Joints
- 4 January 2024
- Published by Springer Nature
- p. 283-293
Experimental Report on Compression Loading Test of Tempered Glass Panels
- 4 January 2024
- Published by Springer Nature
- p. 283-293
Experimental Report on Compression Loading Test of Tempered Glass Panels
- 4 January 2024
- Published by Springer Nature
- p. 133-149
Effect of Hollow Bodies on the Strength and Density of Bubble Concrete
- 4 January 2024
- Published by Springer Nature
- p. 133-149
Effect of Hollow Bodies on the Strength and Density of Bubble Concrete
- Open Access
Effect of Hollow Body Material on Mechanical Properties of Bubble Concrete
The bubble concrete (BC) produced by mixing high-strength hollow bodies into concrete has been proven to be effective in reducing density while maintaining strength. It has been verified that the position distribution of hollow bodies inside hardened BC significantly affects the compressive strength of the BC. However, the effect of hollow body material on the strength of BC has not yet been established. In the present paper, through concrete compression experiments and the nonlinear finite element analysis (F.E.A.), a comparative study of BC with three different hollow bodies—steel spheres, sand bonded stainless steel spheres, and ceramic spheres—has been carried out. The results show that the difference in elastic modulus of hollow bodies and concrete is the primary reason for the inhomogeneous stress distribution inside the concrete. The interface between the hollow body and hardened concrete could be increased using epoxy resin, thus enhancing the compressive strength of BC specimens by 26.6% compared to control concrete. The ceramic material is tightly integrated with the concrete, but as a brittle material, the ceramic cannot sustain colossal stress and subsequently breaks down.
Open AccessEffect of Hollow Body Material on Mechanical Properties of Bubble Concrete
The bubble concrete (BC) produced by mixing high-strength hollow bodies into concrete has been proven to be effective in reducing density while maintaining strength. It has been verified that the position distribution of hollow bodies inside hardened BC significantly affects the compressive strength of the BC. However, the effect of hollow body material on the strength of BC has not yet been established. In the present paper, through concrete compression experiments and the nonlinear finite element analysis (F.E.A.), a comparative study of BC with three different hollow bodies—steel spheres, sand bonded stainless steel spheres, and ceramic spheres—has been carried out. The results show that the difference in elastic modulus of hollow bodies and concrete is the primary reason for the inhomogeneous stress distribution inside the concrete. The interface between the hollow body and hardened concrete could be increased using epoxy resin, thus enhancing the compressive strength of BC specimens by 26.6% compared to control concrete. The ceramic material is tightly integrated with the concrete, but as a brittle material, the ceramic cannot sustain colossal stress and subsequently breaks down.
- Open Access
Experiments and Mechanical Simulation on Bubble Concrete: Studies on the Effects of Shape and Position of Hollow Bodies Mixed in Concrete
This paper proposes a new type of lightweight concrete called bubble concrete, which was developed by mixing concrete with high-strength hollow bodies. In the present study, concave and spherical steel hollow bodies were used not only to form multiple cavities in the concrete but also to transfer internal stresses. Through compression tests, the shape effects and distribution effects of the hollow bodies on the strength and Young’s modulus of concrete were investigated. In addition, the mechanical characteristics of the bubble concrete were simulated by nonlinear elastoplastic finite element analysis to study the stress distribution and failure mechanism. The results indicate that with the proper combination, bubble concrete can reduce its density to 1.971–2.003 g/cm3 (83.3–84.7%, compared to control concrete) and its strength reaches 27.536–28.954 N/mm2.
Open AccessExperiments and Mechanical Simulation on Bubble Concrete: Studies on the Effects of Shape and Position of Hollow Bodies Mixed in Concrete
This paper proposes a new type of lightweight concrete called bubble concrete, which was developed by mixing concrete with high-strength hollow bodies. In the present study, concave and spherical steel hollow bodies were used not only to form multiple cavities in the concrete but also to transfer internal stresses. Through compression tests, the shape effects and distribution effects of the hollow bodies on the strength and Young’s modulus of concrete were investigated. In addition, the mechanical characteristics of the bubble concrete were simulated by nonlinear elastoplastic finite element analysis to study the stress distribution and failure mechanism. The results indicate that with the proper combination, bubble concrete can reduce its density to 1.971–2.003 g/cm3 (83.3–84.7%, compared to control concrete) and its strength reaches 27.536–28.954 N/mm2.