Linghong Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Linghong Liu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Meng-Dong He
Central South University of Forestry and Technology
2 shared publications - Qingzhou Zhang
Hunan Province Key Laboratory of Materials Surface and Interface Science and Technology, Central South University of Forestry and Technology, Changsha 410004, China
2 shared publications - Touwen Fan
Research Institute of Automobile Parts Technology, Hunan Institute of Technology, Hengyang 421002, China
2 shared publications - Dawei Fan
Hunan Province Key Laboratory of Materials Surface and Interface Science and Technology, Central South University of Forestry and Technology, Changsha 410004, China
1 shared publication Dingwang Yuan
Center for High-Resolution Electron Microscopy, College of Materials Science and Engineering, Hunan University, Changsha 410082, China
1 shared publication- Jian-Bo Li
College of Electronic Information and Physics, and Hunan Province Key Laboratory of Materials Surface & Interface Science and Technology, Central South University of Forestry and Technology, Changsha 410004, China
1 shared publication
Latest Publications
- Open Access
A First-Principles Study on the Dislocation Properties of Face-Centered Cubic Metals
The generalized stacking fault energy (GSFE) surface is investigated based on a new anti-alias model and first-principles calculation. Then, based on the outcomes derived from the GSFE surface analysis and the improved Peierls–Nabarro model, the major core properties including core width, Peierls energy, and stress of edge and screw dislocations in Al, Ni, Cu, and Ag are investigated in detail, and the lowest-energy migration pathways for diverse dislocations are investigated. Finally, a quantitative relationship between the ratio of core width to atomic spacing and the Peierls stress is established.
Open AccessA First-Principles Study on the Dislocation Properties of Face-Centered Cubic Metals
The generalized stacking fault energy (GSFE) surface is investigated based on a new anti-alias model and first-principles calculation. Then, based on the outcomes derived from the GSFE surface analysis and the improved Peierls–Nabarro model, the major core properties including core width, Peierls energy, and stress of edge and screw dislocations in Al, Ni, Cu, and Ag are investigated in detail, and the lowest-energy migration pathways for diverse dislocations are investigated. Finally, a quantitative relationship between the ratio of core width to atomic spacing and the Peierls stress is established.
- Open Access
A New Anti-Alias Model of Ab Initio Calculations of the Generalized Stacking Fault Energy in Face-Centered Cubic Crystals
The anti-alias model is an effective method to calculate the generalized stacking fault energy of the hexagonal close-packed crystals, but it has not been applied to the face-centered cubic crystals due to two different stacking faults occurring in the supercell during the sliding process. Based on the symmetry of these two stacking faults and the existing single analytic formula of the generalized stacking fault energy, we successfully extend the anti-alias model to compute the generalized stacking fault energy of face-centered cubic crystals, and the common fcc metals Al, Ni, Ag and Cu are taken as specific examples to illustrate the computational details. Finally, the validity of the proposed model is verified by data comparison and analysis. It is suggested that the anti-alias model is a good choice for the researchers to obtain more accurate generalized stacking fault energy of face-centered cubic metals.
Open AccessA New Anti-Alias Model of Ab Initio Calculations of the Generalized Stacking Fault Energy in Face-Centered Cubic Crystals
The anti-alias model is an effective method to calculate the generalized stacking fault energy of the hexagonal close-packed crystals, but it has not been applied to the face-centered cubic crystals due to two different stacking faults occurring in the supercell during the sliding process. Based on the symmetry of these two stacking faults and the existing single analytic formula of the generalized stacking fault energy, we successfully extend the anti-alias model to compute the generalized stacking fault energy of face-centered cubic crystals, and the common fcc metals Al, Ni, Ag and Cu are taken as specific examples to illustrate the computational details. Finally, the validity of the proposed model is verified by data comparison and analysis. It is suggested that the anti-alias model is a good choice for the researchers to obtain more accurate generalized stacking fault energy of face-centered cubic metals.
- 1 October 2021
- Published by Elsevier in Computational Materials Science
- Vol. 198, 110707
The precipitation competition of η-series precipitates and δ′ precipitates in Li-containing Al-Zn-Mg-Cu alloys
- 1 October 2021
- Published by Elsevier in Computational Materials Science
- Vol. 198, 110707
The precipitation competition of η-series precipitates and δ′ precipitates in Li-containing Al-Zn-Mg-Cu alloys
- Open Access
The Thermal Properties of L12 Phases in Aluminum Enhanced by Alloying Elements
The L12 type trialuminide compounds Al3M possess outstanding mechanical properties, which enable them to be ideal for dispersed strengthening phases for the high-strength thermally stable Al based alloys. Ab-initio calculations based on the density functional theory (DFT) were performed to study the structural, electronic, thermal, and thermodynamic properties of L12-Al3M (M = Er, Hf, Lu, Sc, Ti, Tm, Yb, Li, Mg, Zr) structures in Al alloys. The total energy calculations showed that the L12 structures are quite stable. On the basis of the thermodynamic calculation, we found that the Yb, Lu, Er, and Tm atoms with a larger atomic radii than Al promoted the thermal stability of the Al alloys, and the thermal stability rank has been constructed as: Al3Yb > Al3Lu > Al3Er > Al3Tm > Al, which shows an apparent positive correlation between the atomic size and thermal stability. The chemical bond offers a firm basis upon which to forge links not only within chemistry but also with the macroscopic properties of materials. A careful analysis of the charge density indicated that Yb, Lu, Er, and Tm atoms covalently bonded to Al, providing a strong intrinsic basis for the thermal stability of the respective structures, suggesting that the addition of big atoms (Yb, Lu, Er, and Tm) are beneficial for the thermal stability of Al alloys.
Open AccessThe Thermal Properties of L12 Phases in Aluminum Enhanced by Alloying Elements
The L12 type trialuminide compounds Al3M possess outstanding mechanical properties, which enable them to be ideal for dispersed strengthening phases for the high-strength thermally stable Al based alloys. Ab-initio calculations based on the density functional theory (DFT) were performed to study the structural, electronic, thermal, and thermodynamic properties of L12-Al3M (M = Er, Hf, Lu, Sc, Ti, Tm, Yb, Li, Mg, Zr) structures in Al alloys. The total energy calculations showed that the L12 structures are quite stable. On the basis of the thermodynamic calculation, we found that the Yb, Lu, Er, and Tm atoms with a larger atomic radii than Al promoted the thermal stability of the Al alloys, and the thermal stability rank has been constructed as: Al3Yb > Al3Lu > Al3Er > Al3Tm > Al, which shows an apparent positive correlation between the atomic size and thermal stability. The chemical bond offers a firm basis upon which to forge links not only within chemistry but also with the macroscopic properties of materials. A careful analysis of the charge density indicated that Yb, Lu, Er, and Tm atoms covalently bonded to Al, providing a strong intrinsic basis for the thermal stability of the respective structures, suggesting that the addition of big atoms (Yb, Lu, Er, and Tm) are beneficial for the thermal stability of Al alloys.