Gerson Laerson Drescher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Gerson Laerson Drescher has a total of 147 co-authors. Here are the top co-authors by number of shared publications:
- Trenton Lee Roberts
Department of Crop, Soil, and Environmental Sciences University of Arkansas Division of Agriculture Fayetteville Arkansas USA
13 shared publications - Nathan A. Slaton
Department of Crop, Soil, and Environmental Sciences University of Arkansas Fayetteville Arkansas USA
10 shared publications - Leandro Souza da Silva
Universidade Federal de Santa Maria
9 shared publications - Jason K. Norsworthy
University of Arkansas
7 shared publications - Qamar Sarfaraz
Department of Crop, Soil, and Environmental Sciences University of Arkansas Division of Agriculture Fayetteville Arkansas USA
7 shared publications - Thomas R. Butts
Department of Botany and Plant Pathology Purdue University West Lafayette Indiana USA
7 shared publications
Latest Publications
- Open Access
- 30 September 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (5) , e70549
Corn grain yield, yield components, and potassium nutritional status as affected by potassium fertilization timing
Potassium (K) management is key to maximizing corn ( Zea mays L.) yield potential. We evaluated the effects of K fertilization timing on tissue‐K concentration, grain yield, and yield components (i.e., number of kernel rows per ear, kernels per row, and 1000‐seed weight). Seven field trials were conducted across Arkansas in 2024 and 2025. Fertilizer‐K was applied (112 kg K ha −1 ) either preplant or in‐season, targeting V6, V10, V12, V14, VT, and R2 growth stages, in addition to a no‐K control. Due to differences in crop development rate, recorded growth stages occasionally differed from the target. Preplant soil sampling classified soil‐test K as very low ( 0.05). The number of kernel rows was unaffected by K fertilization timing, whereas kernels per row and 1000‐seed weight responded at selected sites, with maximum values reaching up to 13% and 28% above the control, respectively. Timely diagnosis of K deficiency allows in‐season K fertilization to rescue yield potential.
- 30 September 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (5) , e70549
Open AccessCorn grain yield, yield components, and potassium nutritional status as affected by potassium fertilization timing
Potassium (K) management is key to maximizing corn ( Zea mays L.) yield potential. We evaluated the effects of K fertilization timing on tissue‐K concentration, grain yield, and yield components (i.e., number of kernel rows per ear, kernels per row, and 1000‐seed weight). Seven field trials were conducted across Arkansas in 2024 and 2025. Fertilizer‐K was applied (112 kg K ha −1 ) either preplant or in‐season, targeting V6, V10, V12, V14, VT, and R2 growth stages, in addition to a no‐K control. Due to differences in crop development rate, recorded growth stages occasionally differed from the target. Preplant soil sampling classified soil‐test K as very low ( 0.05). The number of kernel rows was unaffected by K fertilization timing, whereas kernels per row and 1000‐seed weight responded at selected sites, with maximum values reaching up to 13% and 28% above the control, respectively. Timely diagnosis of K deficiency allows in‐season K fertilization to rescue yield potential.
- Open Access
- 28 July 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (4) , e70491
Soil health response to cover cropping and nutrient management in Mid‐Southern US row‐crop production systems
Soil health is important for agricultural resilience. To determine the impacts of agronomic practices like cover cropping, cover crop species, and nutrient management on soil health indicators, soil samples were collected in 2023 from eight long‐term field trials across Arkansas. Soil organic matter (SOM), carbon dioxide respiration (CDR), beta‐glucosidase (BG) enzyme activity, and permanganate oxidizable carbon (POXC) were measured. Additionally, the comprehensive assessment of soil health (CASH) by Cornell University and the soil health assessment score (SHA) values by Ward Labs were determined. Cover cropping, nutrient management, and/or their interactions significantly affected soil health indicators, but these effects were influenced by differences in site‐specific edaphic and climate factors. While cover crops significantly influenced BG activity under both corn ( Zea mays L.) and soybean [ Glycine max (L.) Merr.], the effect was species‐specific; inclusion of legumes generally boosted BG activity. Across all fertilizer rates, cover crop resulted in 4.6% higher SOM and 11.7% higher POXC concentrations than winter fallow. Moreover, indicators including SOM, CDR, BG, and POXC, though greater under cover crop than winter fallow, did not differ among mono‐ or polyculture in improving soil health and crop yield. The correlation between soil health indicators and cash crop yield was moderate to strong ( r values of −0.35 to 0.70; p < 0.05) in irrigated production systems. Results showed that BG, CDR, and POXC, though not strong predictors of crop yield, could be effective indicators for monitoring soil health in irrigated row crop production systems in the Mid‐Southern United States.
- 28 July 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (4) , e70491
Open AccessSoil health response to cover cropping and nutrient management in Mid‐Southern US row‐crop production systems
Soil health is important for agricultural resilience. To determine the impacts of agronomic practices like cover cropping, cover crop species, and nutrient management on soil health indicators, soil samples were collected in 2023 from eight long‐term field trials across Arkansas. Soil organic matter (SOM), carbon dioxide respiration (CDR), beta‐glucosidase (BG) enzyme activity, and permanganate oxidizable carbon (POXC) were measured. Additionally, the comprehensive assessment of soil health (CASH) by Cornell University and the soil health assessment score (SHA) values by Ward Labs were determined. Cover cropping, nutrient management, and/or their interactions significantly affected soil health indicators, but these effects were influenced by differences in site‐specific edaphic and climate factors. While cover crops significantly influenced BG activity under both corn ( Zea mays L.) and soybean [ Glycine max (L.) Merr.], the effect was species‐specific; inclusion of legumes generally boosted BG activity. Across all fertilizer rates, cover crop resulted in 4.6% higher SOM and 11.7% higher POXC concentrations than winter fallow. Moreover, indicators including SOM, CDR, BG, and POXC, though greater under cover crop than winter fallow, did not differ among mono‐ or polyculture in improving soil health and crop yield. The correlation between soil health indicators and cash crop yield was moderate to strong ( r values of −0.35 to 0.70; p < 0.05) in irrigated production systems. Results showed that BG, CDR, and POXC, though not strong predictors of crop yield, could be effective indicators for monitoring soil health in irrigated row crop production systems in the Mid‐Southern United States.
- Open Access
- 10 July 2026
- Published by Wiley in Soil Science Society of America Journal
- Vol. 90 (4) , e70282
Soil sample timing and depth effect on soil health assessment in Mid‐South US row‐crop production systems
Spatial and seasonal variability in soil properties influences soil analysis results, but their impact on soil health assessment has not been well investigated. We evaluated how soil health indicators and scores were affected by soil sampling time (spring, summer, fall, and winter) and depth (0–5, 5–10, and 10–15 cm). Soil samples were collected from 10 long‐term trials across Arkansas, encompassing conventional and no‐tillage practices; rice ( Oryza sativa L.), soybean [ Glycine max (L.) Merr.], and corn ( Zea mays L.) rotations; winter fallow and cover crops; and different phosphorus and potassium rates. Carbon dioxide respiration (CDR), β‐glucosidase (BG) activity, permanganate oxidizable carbon, and soil organic matter were measured. Soil Health Assessment (SHS) and Comprehensive Assessment of Soil Health (CASH) scores were also determined. Fertilizer rate, cover cropping, and timing and depth of soil sampling significantly affected soil health ( p < 0.10). Cover crop and nutrient rate treatments exhibited greater soil health than winter fallow and unfertilized treatments, primarily due to increased nutrient availability and carbon inputs from cash or cover crops. summer and winter sampling times showed greater CDR, BG, and SHS values than fall and spring with fall sampling yielding lower soil health measurements than spring in most cases. The 0‐ to 5‐cm depth exhibited greater soil health values for all indicators, with values decreasing continuously with increasing depth. Regardless of agronomic management, soil health measurements were influenced by sampling depth and timing, highlighting the need for protocols that account for spatial and seasonal fluctuations in soil health monitoring to ensure consistent comparisons.
- 10 July 2026
- Published by Wiley in Soil Science Society of America Journal
- Vol. 90 (4) , e70282
Open AccessSoil sample timing and depth effect on soil health assessment in Mid‐South US row‐crop production systems
Spatial and seasonal variability in soil properties influences soil analysis results, but their impact on soil health assessment has not been well investigated. We evaluated how soil health indicators and scores were affected by soil sampling time (spring, summer, fall, and winter) and depth (0–5, 5–10, and 10–15 cm). Soil samples were collected from 10 long‐term trials across Arkansas, encompassing conventional and no‐tillage practices; rice ( Oryza sativa L.), soybean [ Glycine max (L.) Merr.], and corn ( Zea mays L.) rotations; winter fallow and cover crops; and different phosphorus and potassium rates. Carbon dioxide respiration (CDR), β‐glucosidase (BG) activity, permanganate oxidizable carbon, and soil organic matter were measured. Soil Health Assessment (SHS) and Comprehensive Assessment of Soil Health (CASH) scores were also determined. Fertilizer rate, cover cropping, and timing and depth of soil sampling significantly affected soil health ( p < 0.10). Cover crop and nutrient rate treatments exhibited greater soil health than winter fallow and unfertilized treatments, primarily due to increased nutrient availability and carbon inputs from cash or cover crops. summer and winter sampling times showed greater CDR, BG, and SHS values than fall and spring with fall sampling yielding lower soil health measurements than spring in most cases. The 0‐ to 5‐cm depth exhibited greater soil health values for all indicators, with values decreasing continuously with increasing depth. Regardless of agronomic management, soil health measurements were influenced by sampling depth and timing, highlighting the need for protocols that account for spatial and seasonal fluctuations in soil health monitoring to ensure consistent comparisons.
- Open Access
- 29 June 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (4) , e70465
End‐of‐season corn stalk analysis as a tool to fine‐tune potassium and nitrogen management
Corn ( Zea mays L.) requires proper nutrient management for optimal growth, and tissue testing plays an important role in refining recommendations. Corn stalk nitrate test (CSNT) is used to evaluate nitrogen (N) management; however, a comparable plant‐based diagnostic tool for potassium (K) is lacking. This study evaluated extractants for stalk‐K and explored K sufficiency threshold concentrations for furrow‐irrigated corn production in Arkansas. Eight field trials were conducted across Arkansas in 2023 and 2024, on silt loam soils with very low (−1 ), low (61–90 mg K kg −1 ), and optimum (131–175 mg K kg −1 ) soil‐test K to evaluate corn yield response to K fertilization (0, 37, 75, 112, 149, and 186 kg K ha −1 ). Stalk samples (15–35 cm sections above the soil surface) were collected at physiological maturity and extracted with deionized water and calcium chloride (CaCl 2 ) to measure K and nitrate‐nitrogen (NO 3 ‐N) concentrations. Stalk‐K concentrations consistently increased in response to K fertilization. Deionized water extraction was effective for K and NO 3 ‐N analysis, whereas CaCl 2 produced inflated K values that were weakly related to yield but remained suitable for NO 3 ‐N analysis. Water extractable stalk‐K concentration was significantly associated with relative grain yield ( R 2 = 0.54, p < 0.0001), supporting the preliminary definition of deficient (7142 mg K kg −1 ) stalk‐K concentration thresholds for irrigated corn production. Our results show corn stalk analysis could be an additional tool for evaluating K and N management in irrigated corn systems.
- 29 June 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (4) , e70465
Open AccessEnd‐of‐season corn stalk analysis as a tool to fine‐tune potassium and nitrogen management
Corn ( Zea mays L.) requires proper nutrient management for optimal growth, and tissue testing plays an important role in refining recommendations. Corn stalk nitrate test (CSNT) is used to evaluate nitrogen (N) management; however, a comparable plant‐based diagnostic tool for potassium (K) is lacking. This study evaluated extractants for stalk‐K and explored K sufficiency threshold concentrations for furrow‐irrigated corn production in Arkansas. Eight field trials were conducted across Arkansas in 2023 and 2024, on silt loam soils with very low (−1 ), low (61–90 mg K kg −1 ), and optimum (131–175 mg K kg −1 ) soil‐test K to evaluate corn yield response to K fertilization (0, 37, 75, 112, 149, and 186 kg K ha −1 ). Stalk samples (15–35 cm sections above the soil surface) were collected at physiological maturity and extracted with deionized water and calcium chloride (CaCl 2 ) to measure K and nitrate‐nitrogen (NO 3 ‐N) concentrations. Stalk‐K concentrations consistently increased in response to K fertilization. Deionized water extraction was effective for K and NO 3 ‐N analysis, whereas CaCl 2 produced inflated K values that were weakly related to yield but remained suitable for NO 3 ‐N analysis. Water extractable stalk‐K concentration was significantly associated with relative grain yield ( R 2 = 0.54, p < 0.0001), supporting the preliminary definition of deficient (7142 mg K kg −1 ) stalk‐K concentration thresholds for irrigated corn production. Our results show corn stalk analysis could be an additional tool for evaluating K and N management in irrigated corn systems.
- Open Access
- 28 February 2026
- Published by Wiley in Agrosystems, Geosciences & Environment
- Vol. 9 (1)
Targeted herbicide cost requirements for adoption of See & Spray technology and ways to improve area sprayed
Adopting targeted herbicide applications creates a dynamic problem for producers when considering the economic viability of See & Spray. Research was conducted to estimate how weed area, area sprayed, nozzle selection, sensitivity settings, crops, and regions influence potential herbicide savings with the John Deere See & Spray technology. From 2023 through 2024, producers covered over 510,000 ha and sprayed 212,000 ha with See & Spray technology in the United States. Ways to improve herbicide savings via See & Spray included using narrow nozzle angles rather than wider fan angles and adjusting the sensitivity setting to detect less weed area. Cotton ( Gossypium hirsutum L.) had a higher weed area than soybean [ Glycine max (L.) Merr.; 16.6% vs. 5.1%]. Lower sensitivity settings tended to detect less weed area than higher settings (5.1% at the lowest setting, 9% at the medium setting, and 15.8% at the highest setting). On average, producers needed to spend >$27 ha −1 on herbicides in a single application with See & Spray Premium and >$39 ha −1 with See & Spray Ultimate to economically justify using the technology over a broadcast sprayer. Results indicate that differences in targeted herbicide cost requirements to break even were within $1–$2 ha −1 across regions and within a crop and technology. Ways to improve areas sprayed with targeted applications, factors to consider before application, and insights on ensuring producers’ profitability when adopting this technology are highlighted.
- 28 February 2026
- Published by Wiley in Agrosystems, Geosciences & Environment
- Vol. 9 (1)
Open AccessTargeted herbicide cost requirements for adoption of See & Spray technology and ways to improve area sprayed
Adopting targeted herbicide applications creates a dynamic problem for producers when considering the economic viability of See & Spray. Research was conducted to estimate how weed area, area sprayed, nozzle selection, sensitivity settings, crops, and regions influence potential herbicide savings with the John Deere See & Spray technology. From 2023 through 2024, producers covered over 510,000 ha and sprayed 212,000 ha with See & Spray technology in the United States. Ways to improve herbicide savings via See & Spray included using narrow nozzle angles rather than wider fan angles and adjusting the sensitivity setting to detect less weed area. Cotton ( Gossypium hirsutum L.) had a higher weed area than soybean [ Glycine max (L.) Merr.; 16.6% vs. 5.1%]. Lower sensitivity settings tended to detect less weed area than higher settings (5.1% at the lowest setting, 9% at the medium setting, and 15.8% at the highest setting). On average, producers needed to spend >$27 ha −1 on herbicides in a single application with See & Spray Premium and >$39 ha −1 with See & Spray Ultimate to economically justify using the technology over a broadcast sprayer. Results indicate that differences in targeted herbicide cost requirements to break even were within $1–$2 ha −1 across regions and within a crop and technology. Ways to improve areas sprayed with targeted applications, factors to consider before application, and insights on ensuring producers’ profitability when adopting this technology are highlighted.
- Open Access
- 23 January 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (1)
Defining critical leaf‐ and petiole‐potassium concentrations for monitoring cotton nutritional status
Plant tissue testing is an effective tool for diagnosing crop nutritional status; however, critical tissue‐potassium (K) concentrations have not been established for modern cotton ( Gossypium hirsutum L.) cultivars. We aimed to define critical leaf‐ and petiole‐K concentrations at various growth stages for optimal cotton production. Nine fertilizer‐K rate (0–187 kg K ha −1 ) trials were conducted in a randomized complete block design on silt loam soils with very low to above optimum soil‐test K in Arkansas, during 2023 and 2024. Leaf and petiole samples were collected from first square through the beginning of boll and fiber maturation, to quantify tissue‐K concentrations. At maturity, cotton lint yield was measured. Lint yield was significantly affected by K fertilization ( p ≤ 0.10) in seven out of nine trials, where the unfertilized control yield was 35%–79% of the yield‐maximizing fertilizer‐K rates (56, 75, and 112 kg K ha −1 ). Leaf‐ and petiole‐K concentrations increased with increasing K availability (soil or fertilization). Tissue‐K concentrations peaked at first square and declined throughout cotton reproductive development. Critical leaf‐ and petiole‐K concentrations to maximize yield were 11.1 and 47.3 g K kg −1 at first square, 10.3 and 48.0 g K kg −1 at first flower, and decreased to 5.1 and 7.5 g K kg −1 at eight weeks after first flower, respectively. Petiole‐K concentrations had a stronger relationship with relative yield than leaf‐K ( R 2 range of 0.31–0.65 for petioles and 0.19–0.53 for leaves). Our results suggest petioles are more accurate for monitoring cotton K nutrition, and growth‐stage‐specific critical K concentrations are key for accurately assessing cotton K nutritional status.
- 23 January 2026
- Published by Wiley in Agronomy Journal
- Vol. 118 (1)
Open AccessDefining critical leaf‐ and petiole‐potassium concentrations for monitoring cotton nutritional status
Plant tissue testing is an effective tool for diagnosing crop nutritional status; however, critical tissue‐potassium (K) concentrations have not been established for modern cotton ( Gossypium hirsutum L.) cultivars. We aimed to define critical leaf‐ and petiole‐K concentrations at various growth stages for optimal cotton production. Nine fertilizer‐K rate (0–187 kg K ha −1 ) trials were conducted in a randomized complete block design on silt loam soils with very low to above optimum soil‐test K in Arkansas, during 2023 and 2024. Leaf and petiole samples were collected from first square through the beginning of boll and fiber maturation, to quantify tissue‐K concentrations. At maturity, cotton lint yield was measured. Lint yield was significantly affected by K fertilization ( p ≤ 0.10) in seven out of nine trials, where the unfertilized control yield was 35%–79% of the yield‐maximizing fertilizer‐K rates (56, 75, and 112 kg K ha −1 ). Leaf‐ and petiole‐K concentrations increased with increasing K availability (soil or fertilization). Tissue‐K concentrations peaked at first square and declined throughout cotton reproductive development. Critical leaf‐ and petiole‐K concentrations to maximize yield were 11.1 and 47.3 g K kg −1 at first square, 10.3 and 48.0 g K kg −1 at first flower, and decreased to 5.1 and 7.5 g K kg −1 at eight weeks after first flower, respectively. Petiole‐K concentrations had a stronger relationship with relative yield than leaf‐K ( R 2 range of 0.31–0.65 for petioles and 0.19–0.53 for leaves). Our results suggest petioles are more accurate for monitoring cotton K nutrition, and growth‐stage‐specific critical K concentrations are key for accurately assessing cotton K nutritional status.
- Open Access
- 4 November 2025
- Published by Cambridge University Press (CUP) in Weed Technology
- Vol. 40, 1-32
Weed population impacts using targeted herbicide applications with a precision sprayer in soybean over a three-year period
Targeted herbicide applications have the potential to reduce herbicide use but they pose an inherent risk of missing late-season weed escapes. Furthermore, relying on targeted use of residual herbicides may increase weed emergence relative to broadcast applications. Research was conducted over a 3-yr period in Keiser, Arkansas, to compare traditional broadcast applications to targeted postemergence applications of various herbicides to soybean cultivars that are known to be resistant to glyphosate, glufosinate, and dicamba. The herbicide treatment protocol was consistent across treatments with a broadcast-applied preemergence residual, and a postemergence combination that included glufosinate + glyphosate + S -metolachlor followed by glufosinate + acetochlor, applied both via broadcast or targeted at the highest and lowest spray sensitivities of the John Deere See & Spray technology. The soil seedbank was similar at trial initiation across treatments, and there was no increase in the seedbank over 3 yr of broadcast and targeted applications at the highest spray sensitivity. Averaged over application timing, when herbicides were applied at the lowest spray sensitivity the weed density rose from 867 plants ha −1 to 2,870 plants ha −1 in Year 2, to 11,300 plants ha −1 in Year 3. This response is likely due to more Palmer amaranth escapes when the crop was harvested with an average of >1,000 plants ha −1 over the years compared with weed density after herbicides were applied with the highest spray sensitivity and via broadcast. Targeted applications improved profitability by reducing herbicide use and increasing application efficiency, providing an average savings of US$43.22 ha −1 to $129.19 ha −1 relative to broadcast postemergence cost of $227.22 ha −1 . The area sprayed was reduced by 20% to 90%, with an average spraying at early postemergence of 41.3% and 57.9% and at mid-postemergence equaling 48.1% and 49.3% when herbicides were applied with the lowest and highest spray sensitivities, respectively. The only difference in the area sprayed between sensitivity settings occurred early postemergence. Based on the results of this experiment, producers could apply postemergence herbicides targeted to weeds that grow with soybean to increase profitability, but the lowest sensitivity resulted in unacceptable increases to the weed seedbank, which could affect management in future years.
- 4 November 2025
- Published by Cambridge University Press (CUP) in Weed Technology
- Vol. 40, 1-32
Open AccessWeed population impacts using targeted herbicide applications with a precision sprayer in soybean over a three-year period
Targeted herbicide applications have the potential to reduce herbicide use but they pose an inherent risk of missing late-season weed escapes. Furthermore, relying on targeted use of residual herbicides may increase weed emergence relative to broadcast applications. Research was conducted over a 3-yr period in Keiser, Arkansas, to compare traditional broadcast applications to targeted postemergence applications of various herbicides to soybean cultivars that are known to be resistant to glyphosate, glufosinate, and dicamba. The herbicide treatment protocol was consistent across treatments with a broadcast-applied preemergence residual, and a postemergence combination that included glufosinate + glyphosate + S -metolachlor followed by glufosinate + acetochlor, applied both via broadcast or targeted at the highest and lowest spray sensitivities of the John Deere See & Spray technology. The soil seedbank was similar at trial initiation across treatments, and there was no increase in the seedbank over 3 yr of broadcast and targeted applications at the highest spray sensitivity. Averaged over application timing, when herbicides were applied at the lowest spray sensitivity the weed density rose from 867 plants ha −1 to 2,870 plants ha −1 in Year 2, to 11,300 plants ha −1 in Year 3. This response is likely due to more Palmer amaranth escapes when the crop was harvested with an average of >1,000 plants ha −1 over the years compared with weed density after herbicides were applied with the highest spray sensitivity and via broadcast. Targeted applications improved profitability by reducing herbicide use and increasing application efficiency, providing an average savings of US$43.22 ha −1 to $129.19 ha −1 relative to broadcast postemergence cost of $227.22 ha −1 . The area sprayed was reduced by 20% to 90%, with an average spraying at early postemergence of 41.3% and 57.9% and at mid-postemergence equaling 48.1% and 49.3% when herbicides were applied with the lowest and highest spray sensitivities, respectively. The only difference in the area sprayed between sensitivity settings occurred early postemergence. Based on the results of this experiment, producers could apply postemergence herbicides targeted to weeds that grow with soybean to increase profitability, but the lowest sensitivity resulted in unacceptable increases to the weed seedbank, which could affect management in future years.
- Open Access
- 29 October 2025
- Published by Wiley in Soil Science Society of America Journal
- Vol. 89 (6)
Furrow‐irrigated cotton yield and fiber quality response to potassium fertilization
Potassium (K) deficiency is a common yield‐limiting factor in cotton ( Gossypium hirsutum L.) production, requiring effective management to minimize yield losses and maintain fiber quality. We evaluated how K availability influences cotton lint yield and fiber quality. Ten fertilizer‐K rate (0–187 kg K ha −1 ) trials were conducted on silt loam soils with soil‐test K (STK) ranging from very low to above optimum during the 2023 and 2024 growing seasons. Cotton was planted in raised beds and furrow‐irrigated, and lint yield, turnout, and fiber quality (i.e., fiber length, micronaire, uniformity, strength, and elongation) were measured at maturity. Cotton lint yield was positively affected by fertilizer‐K rates ( p ≤ 0.10) at STK ≤ 114 mg K kg −1 . Yields were maximized at responsive sites with applications of 56 kg K ha −1 in long‐term trials and 37, 75, or 112 kg K ha −1 in single‐site‐year trials, showing yield increases of 20%, 53%, 47%, and 70% compared to the no‐K control, respectively. Lint turnout and fiber quality were affected by K availability. Overall, at yield‐maximizing fertilizer‐K rates, lint turnout was 2.4% greater across cultivars in relation to the control. Similarly, fiber elongation increased by 0.35%. At sites with Very Low STK, as little as 37 kg K ha −1 increased lint uniformity and strength up to 0.67% and 1.84 g tex −1 . Micronaire increased on average by 0.50, with greatest values occurring with 112 kg K ha −1 application. These findings suggest adequate K management is key to maximizing both cotton yield potential and fiber quality.
- 29 October 2025
- Published by Wiley in Soil Science Society of America Journal
- Vol. 89 (6)
Open AccessFurrow‐irrigated cotton yield and fiber quality response to potassium fertilization
Potassium (K) deficiency is a common yield‐limiting factor in cotton ( Gossypium hirsutum L.) production, requiring effective management to minimize yield losses and maintain fiber quality. We evaluated how K availability influences cotton lint yield and fiber quality. Ten fertilizer‐K rate (0–187 kg K ha −1 ) trials were conducted on silt loam soils with soil‐test K (STK) ranging from very low to above optimum during the 2023 and 2024 growing seasons. Cotton was planted in raised beds and furrow‐irrigated, and lint yield, turnout, and fiber quality (i.e., fiber length, micronaire, uniformity, strength, and elongation) were measured at maturity. Cotton lint yield was positively affected by fertilizer‐K rates ( p ≤ 0.10) at STK ≤ 114 mg K kg −1 . Yields were maximized at responsive sites with applications of 56 kg K ha −1 in long‐term trials and 37, 75, or 112 kg K ha −1 in single‐site‐year trials, showing yield increases of 20%, 53%, 47%, and 70% compared to the no‐K control, respectively. Lint turnout and fiber quality were affected by K availability. Overall, at yield‐maximizing fertilizer‐K rates, lint turnout was 2.4% greater across cultivars in relation to the control. Similarly, fiber elongation increased by 0.35%. At sites with Very Low STK, as little as 37 kg K ha −1 increased lint uniformity and strength up to 0.67% and 1.84 g tex −1 . Micronaire increased on average by 0.50, with greatest values occurring with 112 kg K ha −1 application. These findings suggest adequate K management is key to maximizing both cotton yield potential and fiber quality.
- Open Access
- 28 October 2025
- Published by Wiley in Soil Science Society of America Journal
- Vol. 89 (6)
Improved soil property prediction models for rice paddies using measured nutrients
Traditional laboratory analyses of soil texture and soil organic matter (SOM) are time consuming and labor‐intensive, so they are impractical to be measured at the same scale as routine nutrient testing. The objective of this study was to determine soil clay, sand, and SOM across a large number of samples by improving mixed‐land‐use predictive models proposed by Drescher et al. in 2024, creating a rice ( Oryza sativa L.)‐specific set of models that integrates soil pH, Mehlich‐3 extractable nutrients, and estimated cation exchange capacity (EstCEC). With a clustering analysis, a soil dataset containing 179 samples from major rice producing states in the United States was split into a training set (80%) for rice model development and a testing set (20%) for validation. Another dataset of 111 samples from Arkansas was used to compare the performance of rice models with mixed‐land‐use models. After validation, a high‐accuracy clay model ( R 2 = 0.84; RMSE = 68.14 g kg −1 ) was obtained using pH, phosphorous (P), potassium (K), calcium (Ca), and magnesium (Mg). The sand model containing pH, Ca, Mg, and EstCEC fit with moderate accuracy ( R 2 = 0.36; RMSE = 89.94 g kg −1 ). The best SOM model relied on pH, P, K, Mg, and EstCEC ( R 2 = 0.80; RMSE = 4.28 g kg −1 ). The Arkansas rice soil dataset showed that rice models enhanced SOM prediction ( R 2 increased from 0.78 to 0.81), and they improved the overall soil textural classification accuracy to 70% versus 58% by mixed‐land‐use models. While our models are suitable for clay and silt‐dominated classes, such as clay, silt loam, clay loam, and silty clay loam, they may not be for several sand‐dominated classes. This study provides a tool by which to efficiently and inexpensively estimate key soil physicochemical properties for agricultural decision‐making but the overall utility of our models for rice soil textural classification is limited at present.
- 28 October 2025
- Published by Wiley in Soil Science Society of America Journal
- Vol. 89 (6)
Open AccessImproved soil property prediction models for rice paddies using measured nutrients
Traditional laboratory analyses of soil texture and soil organic matter (SOM) are time consuming and labor‐intensive, so they are impractical to be measured at the same scale as routine nutrient testing. The objective of this study was to determine soil clay, sand, and SOM across a large number of samples by improving mixed‐land‐use predictive models proposed by Drescher et al. in 2024, creating a rice ( Oryza sativa L.)‐specific set of models that integrates soil pH, Mehlich‐3 extractable nutrients, and estimated cation exchange capacity (EstCEC). With a clustering analysis, a soil dataset containing 179 samples from major rice producing states in the United States was split into a training set (80%) for rice model development and a testing set (20%) for validation. Another dataset of 111 samples from Arkansas was used to compare the performance of rice models with mixed‐land‐use models. After validation, a high‐accuracy clay model ( R 2 = 0.84; RMSE = 68.14 g kg −1 ) was obtained using pH, phosphorous (P), potassium (K), calcium (Ca), and magnesium (Mg). The sand model containing pH, Ca, Mg, and EstCEC fit with moderate accuracy ( R 2 = 0.36; RMSE = 89.94 g kg −1 ). The best SOM model relied on pH, P, K, Mg, and EstCEC ( R 2 = 0.80; RMSE = 4.28 g kg −1 ). The Arkansas rice soil dataset showed that rice models enhanced SOM prediction ( R 2 increased from 0.78 to 0.81), and they improved the overall soil textural classification accuracy to 70% versus 58% by mixed‐land‐use models. While our models are suitable for clay and silt‐dominated classes, such as clay, silt loam, clay loam, and silty clay loam, they may not be for several sand‐dominated classes. This study provides a tool by which to efficiently and inexpensively estimate key soil physicochemical properties for agricultural decision‐making but the overall utility of our models for rice soil textural classification is limited at present.