Larisa-Maria Petrila
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Larisa-Maria Petrila has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Marcela Mihai
Petru Poni Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi, Romania
9 shared publications - Florin Bucatariu
Petru Poni Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi, Romania
8 shared publications - Marius-Mihai Zaharia
Petru Poni Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi, Romania
4 shared publications - Timeea-Anastasia Ciobanu
Petru Poni Institute of Macromolecular Chemistry, 41A Grigore Ghica Voda Alley, 700487 Iasi, Romania
3 shared publications - Carmen Teodosiu
Department of Environmental Engineering and Management, “Cristofor Simionescu” Faculty of Chemical Engineering and Environmental Protection, “Gheorghe Asachi” Technical University of Iasi, 73 Mangeron Blvd., 700050 Iasi, Romania
2 shared publications Carmen Teodosiu
1 shared publication
Latest Publications
- Open Access
- 20 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (18) , 9324
Multicomponent Interpolyelectrolyte/Catalase Complexes Deposited onto Sand Microparticles with Sorption/Degradation Properties Toward Pollutants
The one-step deposition of binary and ternary polyelectrolyte complexes (PECs) based on poly(ethyleneimine) (PEI), catalase (Cat), and poly(sodium methacrylate) (PMANa) onto quartz sand microparticles (180 μm average diameter) resulted in the formation of sand/polyelectrolyte/enzyme composites with sorption/degradation properties, demonstrated in both static and dynamic conditions toward a model pollutant (indigo carmine (IC)). Prior to the deposition onto a solid surface, the capacity of the pairs PEI/Cat, PMANa/Cat, and PEI/PMANa/Cat to form binary and ternary PECs was studied by dynamic light scattering. Then, two types of composites were prepared, either by including Cat in the initial mixture of components used to form the composites (sand/Cat-PECs) or by adding Cat after the sand/PEC composite formation (sand/PECs/Cat). The distribution of the enzyme in the formed shell of the composites or onto the external surface played an important role in the subsequent sorption/degradation of IC in the presence/absence of H2O2. The newly synthesized sand/polyelectrolyte/enzyme composites could immobilize and degrade dye molecules at high flow rates (2–15 mL/min) in dynamic conditions, demonstrating that this new type of composite represent very promising materials for application in water cleaning.
- 20 September 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (18) , 9324
Open AccessMulticomponent Interpolyelectrolyte/Catalase Complexes Deposited onto Sand Microparticles with Sorption/Degradation Properties Toward Pollutants
The one-step deposition of binary and ternary polyelectrolyte complexes (PECs) based on poly(ethyleneimine) (PEI), catalase (Cat), and poly(sodium methacrylate) (PMANa) onto quartz sand microparticles (180 μm average diameter) resulted in the formation of sand/polyelectrolyte/enzyme composites with sorption/degradation properties, demonstrated in both static and dynamic conditions toward a model pollutant (indigo carmine (IC)). Prior to the deposition onto a solid surface, the capacity of the pairs PEI/Cat, PMANa/Cat, and PEI/PMANa/Cat to form binary and ternary PECs was studied by dynamic light scattering. Then, two types of composites were prepared, either by including Cat in the initial mixture of components used to form the composites (sand/Cat-PECs) or by adding Cat after the sand/PEC composite formation (sand/PECs/Cat). The distribution of the enzyme in the formed shell of the composites or onto the external surface played an important role in the subsequent sorption/degradation of IC in the presence/absence of H2O2. The newly synthesized sand/polyelectrolyte/enzyme composites could immobilize and degrade dye molecules at high flow rates (2–15 mL/min) in dynamic conditions, demonstrating that this new type of composite represent very promising materials for application in water cleaning.
- Open Access
Self-Assembled (Nano)Structures of Human Serum Albumin with Thermoresponsive Chitosan-g-PNIPAM Graft Copolymer
Protein–polyelectrolyte entities (complex, coacervates, flocs, gels, etc.) are of great interest due to their potential applications in biological and medical fields. This study focuses on investigating the interactions between a model protein, human serum albumin (HSA) and a newly synthesized hybrid thermoresponsive copolymer based on chitosan polysaccharide grafted with poly(N-isopropylacrylamide) synthetic polymer chains (Chit-g-PNIPAM), in aqueous media, by mixing the individual component aqueous solutions. Depending on the mixing molar ratio and the order of addition of the two components (protein and copolymer), either stable nanostructured suspension or macrostructures’ phase separation have been observed. Dynamic light scattering (DLS) results reveal that the Chit-g-PNIPAM/HSAx (molar ratio 5:x, where x = 1, 2, 3, 5, 10 and 15) nanostructures’ and HSA/Chit-g-PNIPAMx (molar ratio 100:x, where x = 1, 2, 3, 10, 20, 30, 40 and 50) structures’ formation depend on the molar ratio of the two components as well as on the order of addition, with first component amount being kept constant in aqueous solution and second component solution added drop-by-drop in the solution of the first component. Additional information regarding the thermoresponsiveness and stability vs time of the formed (nano)structures were acquired using turbidimetry and DLS measurements.
Open AccessSelf-Assembled (Nano)Structures of Human Serum Albumin with Thermoresponsive Chitosan-g-PNIPAM Graft Copolymer
Protein–polyelectrolyte entities (complex, coacervates, flocs, gels, etc.) are of great interest due to their potential applications in biological and medical fields. This study focuses on investigating the interactions between a model protein, human serum albumin (HSA) and a newly synthesized hybrid thermoresponsive copolymer based on chitosan polysaccharide grafted with poly(N-isopropylacrylamide) synthetic polymer chains (Chit-g-PNIPAM), in aqueous media, by mixing the individual component aqueous solutions. Depending on the mixing molar ratio and the order of addition of the two components (protein and copolymer), either stable nanostructured suspension or macrostructures’ phase separation have been observed. Dynamic light scattering (DLS) results reveal that the Chit-g-PNIPAM/HSAx (molar ratio 5:x, where x = 1, 2, 3, 5, 10 and 15) nanostructures’ and HSA/Chit-g-PNIPAMx (molar ratio 100:x, where x = 1, 2, 3, 10, 20, 30, 40 and 50) structures’ formation depend on the molar ratio of the two components as well as on the order of addition, with first component amount being kept constant in aqueous solution and second component solution added drop-by-drop in the solution of the first component. Additional information regarding the thermoresponsiveness and stability vs time of the formed (nano)structures were acquired using turbidimetry and DLS measurements.
- Open Access
- 5 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (19) , 10725
Dynamic Ultra-Fast Sorption/Desorption of Indigo Carmine onto/from Versatile Core-Shell Composite Microparticles
The direct deposition of highly concentrated polyelectrolyte complexes based on poly(ethyleneimine) (PEI) and poly(sodium methacrylate) (PMANa) onto inorganic sand microparticles (F100 and F200) resulted in the formation of versatile core-shell composites with fast removal properties in dynamic conditions toward anionic charged pollutants. Herein, in situ-generated nonstoichiometric PEI/PMANa polyelectrolyte complexes were directly precipitated as a soft organic shell onto solid sand microparticles at a 5% mass ratio (organic/inorganic part = 5%, w/w%). The sorption of an anionic model pollutant (Indigo Carmine (IC)) onto the composite particles in dynamic conditions depended on the inorganic core size, the flow rate, the bed type (fixed or fluidized) and the initial dye concentration. The maximum sorption capacity, after 10 cycles of sorption/desorption of IC onto F100@P5% and F200@P5%, was between 16 and 18 mg IC/mL composite. The newly synthesized core-shell composites could immobilize IC at a high flow rate (8 mL/min), either from concentrated (CIC = 60 mg/L) or very diluted (CIC = 0.2 mg/L) IC aqueous solution, demonstrating that this type of material could be promising in water treatment or efficient in solid-phase extraction (concentration factor of 2000).
- 5 October 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (19) , 10725
Open AccessDynamic Ultra-Fast Sorption/Desorption of Indigo Carmine onto/from Versatile Core-Shell Composite Microparticles
The direct deposition of highly concentrated polyelectrolyte complexes based on poly(ethyleneimine) (PEI) and poly(sodium methacrylate) (PMANa) onto inorganic sand microparticles (F100 and F200) resulted in the formation of versatile core-shell composites with fast removal properties in dynamic conditions toward anionic charged pollutants. Herein, in situ-generated nonstoichiometric PEI/PMANa polyelectrolyte complexes were directly precipitated as a soft organic shell onto solid sand microparticles at a 5% mass ratio (organic/inorganic part = 5%, w/w%). The sorption of an anionic model pollutant (Indigo Carmine (IC)) onto the composite particles in dynamic conditions depended on the inorganic core size, the flow rate, the bed type (fixed or fluidized) and the initial dye concentration. The maximum sorption capacity, after 10 cycles of sorption/desorption of IC onto F100@P5% and F200@P5%, was between 16 and 18 mg IC/mL composite. The newly synthesized core-shell composites could immobilize IC at a high flow rate (8 mL/min), either from concentrated (CIC = 60 mg/L) or very diluted (CIC = 0.2 mg/L) IC aqueous solution, demonstrating that this type of material could be promising in water treatment or efficient in solid-phase extraction (concentration factor of 2000).
- Open Access
- 27 January 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (2)
A green approach combining polyelectrolyte-based core-shell microparticles and laccase for indigo carmine degradation
- 27 January 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (2)
Open AccessA green approach combining polyelectrolyte-based core-shell microparticles and laccase for indigo carmine degradation
- Open Access
Sand/Polyethyleneimine Composites with Enhanced Sorption/Desorption Properties toward Pollutants
The direct deposition of polyethyleneimine (PEI), a weak polycation with a large content of amino groups, onto sand fractions with different sizes (F70, F100, F200, and F355), resulted in versatile core-shell sorbents for water cleaning. Herein, PEI and the weak polyanion poly(acrylic acid) (PAA) were directly precipitated as an nonstoichiometric polyelectrolyte complex ([PEI]:[PAA] = 2:1) onto a sand surface followed by cross-linking with glutaraldehyde (GA) at three molar ratios ([CHO]:[amine] = 1:10; 1:5; 1:1 = r). Non-crosslinked polyelectrolyte chains were washed out in strongly basic (pH 14) and acidic (pH 0) media. The sand/PEI-GA composites were evaluated to determine the organic shell stability using swelling experiments and X-ray photoelectron spectroscopy. The sorbed/desorbed amount of two model pollutants (copper ions and bromocresol green) in column experiments depended on the sand fraction size and cross-linking degree of the PEI shell. The maximum recorded values, after five loading/release cycles of pollutant species onto F70/PEI-GAr, F100/PEI-GAr, F200/PEI-GAr, and F355/PEI-GAr, were situated between the 0.7–5.5 mg Cu2+/mL column and 3.7–15 mg BCG/mL column. Sand/PEI-GAr composites could act as promising sorbents, low-cost and eco-friendly, which could be applied for water purification procedures.
Open AccessSand/Polyethyleneimine Composites with Enhanced Sorption/Desorption Properties toward Pollutants
The direct deposition of polyethyleneimine (PEI), a weak polycation with a large content of amino groups, onto sand fractions with different sizes (F70, F100, F200, and F355), resulted in versatile core-shell sorbents for water cleaning. Herein, PEI and the weak polyanion poly(acrylic acid) (PAA) were directly precipitated as an nonstoichiometric polyelectrolyte complex ([PEI]:[PAA] = 2:1) onto a sand surface followed by cross-linking with glutaraldehyde (GA) at three molar ratios ([CHO]:[amine] = 1:10; 1:5; 1:1 = r). Non-crosslinked polyelectrolyte chains were washed out in strongly basic (pH 14) and acidic (pH 0) media. The sand/PEI-GA composites were evaluated to determine the organic shell stability using swelling experiments and X-ray photoelectron spectroscopy. The sorbed/desorbed amount of two model pollutants (copper ions and bromocresol green) in column experiments depended on the sand fraction size and cross-linking degree of the PEI shell. The maximum recorded values, after five loading/release cycles of pollutant species onto F70/PEI-GAr, F100/PEI-GAr, F200/PEI-GAr, and F355/PEI-GAr, were situated between the 0.7–5.5 mg Cu2+/mL column and 3.7–15 mg BCG/mL column. Sand/PEI-GAr composites could act as promising sorbents, low-cost and eco-friendly, which could be applied for water purification procedures.
- Open Access
Polymer/Enzyme Composite Materials—Versatile Catalysts with Multiple Applications
A significant interest was granted lately to enzymes, which are versatile catalysts characterized by natural origin, with high specificity and selectivity for particular substrates. Additionally, some enzymes are involved in the production of high-valuable products, such as antibiotics, while others are known for their ability to transform emerging contaminates, such as dyes and pesticides, to simpler molecules with a lower environmental impact. Nevertheless, the use of enzymes in industrial applications is limited by their reduced stability in extreme conditions and by their difficult recovery and reusability. Rationally, enzyme immobilization on organic or inorganic matrices proved to be one of the most successful innovative approaches to increase the stability of enzymatic catalysts. By the immobilization of enzymes on support materials, composite biocatalysts are obtained that pose an improved stability, preserving the enzymatic activity and some of the support material’s properties. Of high interest are the polymer/enzyme composites, which are obtained by the chemical or physical attachment of enzymes on polymer matrices. This review highlights some of the latest findings in the field of polymer/enzyme composites, classified according to the morphology of the resulting materials, following their most important applications.
Open AccessPolymer/Enzyme Composite Materials—Versatile Catalysts with Multiple Applications
A significant interest was granted lately to enzymes, which are versatile catalysts characterized by natural origin, with high specificity and selectivity for particular substrates. Additionally, some enzymes are involved in the production of high-valuable products, such as antibiotics, while others are known for their ability to transform emerging contaminates, such as dyes and pesticides, to simpler molecules with a lower environmental impact. Nevertheless, the use of enzymes in industrial applications is limited by their reduced stability in extreme conditions and by their difficult recovery and reusability. Rationally, enzyme immobilization on organic or inorganic matrices proved to be one of the most successful innovative approaches to increase the stability of enzymatic catalysts. By the immobilization of enzymes on support materials, composite biocatalysts are obtained that pose an improved stability, preserving the enzymatic activity and some of the support material’s properties. Of high interest are the polymer/enzyme composites, which are obtained by the chemical or physical attachment of enzymes on polymer matrices. This review highlights some of the latest findings in the field of polymer/enzyme composites, classified according to the morphology of the resulting materials, following their most important applications.
- 6 September 2022
- Published by MathDoc/Centre Mersenne in Comptes Rendus. Chimie
- Vol. 25 (S3) , 95-108
Versatile nanostructured SiO 2 /cross-linked polyelectrolyte composites for emerging pollutants removal from aqueous media
Linear and branched poly(ethyleneimines) and poly(acrylic acid) have been used in the construction of nanostructured thin multilayer organic shell onto silica microparticles. After glutaraldehyde selective crosslinking of part of the amino groups, the polyanionic chains were removed on strong basic media. The core/shell microparticles, with amino groups active sites, could interact with anionic charged species dissolved in aqueous media. Batch/column experiments show that the polyanion extracted composites present the best performance toward gallic acid sorption ( ∼ 30 mg/g composite), as compared to the non-extracted samples ( ∼ 6 mg/g). The multiple sorption/desorption studies demonstrated the reusability of the composites for water/wastewater treatment applications in at least 10 consecutive cycles without significant loss of sorption capacity.
- 6 September 2022
- Published by MathDoc/Centre Mersenne in Comptes Rendus. Chimie
- Vol. 25 (S3) , 95-108
Versatile nanostructured SiO 2 /cross-linked polyelectrolyte composites for emerging pollutants removal from aqueous media
Linear and branched poly(ethyleneimines) and poly(acrylic acid) have been used in the construction of nanostructured thin multilayer organic shell onto silica microparticles. After glutaraldehyde selective crosslinking of part of the amino groups, the polyanionic chains were removed on strong basic media. The core/shell microparticles, with amino groups active sites, could interact with anionic charged species dissolved in aqueous media. Batch/column experiments show that the polyanion extracted composites present the best performance toward gallic acid sorption ( ∼ 30 mg/g composite), as compared to the non-extracted samples ( ∼ 6 mg/g). The multiple sorption/desorption studies demonstrated the reusability of the composites for water/wastewater treatment applications in at least 10 consecutive cycles without significant loss of sorption capacity.
- Open Access
An Overview on Composite Sorbents Based on Polyelectrolytes Used in Advanced Wastewater Treatment
Advanced wastewater treatment processes are required to implement wastewater reuse in agriculture or industry, the efficient removal of targeted priority and emerging organic & inorganic pollutants being compulsory (due to their eco-toxicological and human health effects, bio-accumulative, and degradation characteristics). Various processes such as membrane separations, adsorption, advanced oxidation, filtration, disinfection may be used in combination with one or more conventional treatment stages, but technical and environmental criteria are important to assess their application. Natural and synthetic polyelectrolytes combined with some inorganic materials or other organic or inorganic polymers create new materials (composites) that are currently used in sorption of toxic pollutants. The recent developments on the synthesis and characterization of composites based on polyelectrolytes, divided according to their macroscopic shape—beads, core-shell, gels, nanofibers, membranes—are discussed, and a correlation of their actual structure and properties with the adsorption mechanisms and removal efficiencies of various pollutants in aqueous media (priority and emerging pollutants or other model pollutants) are presented.
Open AccessAn Overview on Composite Sorbents Based on Polyelectrolytes Used in Advanced Wastewater Treatment
Advanced wastewater treatment processes are required to implement wastewater reuse in agriculture or industry, the efficient removal of targeted priority and emerging organic & inorganic pollutants being compulsory (due to their eco-toxicological and human health effects, bio-accumulative, and degradation characteristics). Various processes such as membrane separations, adsorption, advanced oxidation, filtration, disinfection may be used in combination with one or more conventional treatment stages, but technical and environmental criteria are important to assess their application. Natural and synthetic polyelectrolytes combined with some inorganic materials or other organic or inorganic polymers create new materials (composites) that are currently used in sorption of toxic pollutants. The recent developments on the synthesis and characterization of composites based on polyelectrolytes, divided according to their macroscopic shape—beads, core-shell, gels, nanofibers, membranes—are discussed, and a correlation of their actual structure and properties with the adsorption mechanisms and removal efficiencies of various pollutants in aqueous media (priority and emerging pollutants or other model pollutants) are presented.
- Open Access
Polyelectrolyte Multilayers: An Overview on Fabrication, Properties, and Biomedical and Environmental Applications
Polyelectrolyte multilayers are versatile materials that are used in a large number of domains, including biomedical and environmental applications. The fabrication of polyelectrolyte multilayers using the layer-by-layer technique is one of the simplest methods to obtain composite functional materials. The properties of the final material can be easily tuned by changing the deposition conditions and the used building blocks. This review presents the main characteristics of polyelectrolyte multilayers, the fabrication methods currently used, and the factors influencing the layer-by-layer assembly of polyelectrolytes. The last section of this paper presents some of the most important applications of polyelectrolyte multilayers, with a special focus on biomedical and environmental applications.
Open AccessPolyelectrolyte Multilayers: An Overview on Fabrication, Properties, and Biomedical and Environmental Applications
Polyelectrolyte multilayers are versatile materials that are used in a large number of domains, including biomedical and environmental applications. The fabrication of polyelectrolyte multilayers using the layer-by-layer technique is one of the simplest methods to obtain composite functional materials. The properties of the final material can be easily tuned by changing the deposition conditions and the used building blocks. This review presents the main characteristics of polyelectrolyte multilayers, the fabrication methods currently used, and the factors influencing the layer-by-layer assembly of polyelectrolytes. The last section of this paper presents some of the most important applications of polyelectrolyte multilayers, with a special focus on biomedical and environmental applications.