Juraj Svatík
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Juraj Svatík has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- František Ondreáš
Contipro a.s., Dolní Dobrouč 401, 561 02 Dolní Dobrouč, Czech Republic; Brno University of Technology, Central European Institute of Technology, Purkyňova 656/123, 612 00 Brno, Czech Republic
6 shared publications - Petr Lepcio
Central European Institute of Technology, Brno University of Technology, Purkyňova 656/123, 612 00 Brno, Czech Republic
6 shared publications Alan J. Lesser
University of Massachusetts Amherst 120 Governors Drive Amherst MA 01003 USA
2 shared publicationsJosef Jančář
2 shared publicationsKlára Zárybnická
2 shared publications- Marek Zboncak
Central European Institute of Technology, Brno University of Technology, Brno 61200, Czech Republic
2 shared publications
Latest Publications
- 21 November 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (5)
Effect of the nanoparticles on the morphology and mechanical performance of thermally blown 3D printed HIPS foams
Cellular polymer nanocomposites can combine high mechanical performance with low density. However, the manufacturing of porous nanocomposites into complex shapes can represent a challenge. Therefore, this article deals with the preparation, characterization, and 3D printing of porous nanocomposites. The filaments were extruded from the polymer nanocomposite filled by thermal chemical blowing agent, and then processed by 3D printing into the required shapes. In‐situ and post‐treatment foaming strategies were investigated and compared. The nanoparticles (NPs) significantly affected the processing, structure, thermal and mechanical properties of polymeric foams. The NPs, serving as a nucleating agent, allowed preparation of smaller pores and led to finer and more homogeneous foams. At the same time, they reinforced foam walls and thus improved mechanical properties. Moreover, NPs catalyzed decomposition of the blowing agent grains at lower temperature which brought about faster and more efficient foaming. This study showed the straightforward approach to prepare mechanically robust lightweight 3D printed materials.
- 21 November 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 140 (5)
Effect of the nanoparticles on the morphology and mechanical performance of thermally blown 3D printed HIPS foams
Cellular polymer nanocomposites can combine high mechanical performance with low density. However, the manufacturing of porous nanocomposites into complex shapes can represent a challenge. Therefore, this article deals with the preparation, characterization, and 3D printing of porous nanocomposites. The filaments were extruded from the polymer nanocomposite filled by thermal chemical blowing agent, and then processed by 3D printing into the required shapes. In‐situ and post‐treatment foaming strategies were investigated and compared. The nanoparticles (NPs) significantly affected the processing, structure, thermal and mechanical properties of polymeric foams. The NPs, serving as a nucleating agent, allowed preparation of smaller pores and led to finer and more homogeneous foams. At the same time, they reinforced foam walls and thus improved mechanical properties. Moreover, NPs catalyzed decomposition of the blowing agent grains at lower temperature which brought about faster and more efficient foaming. This study showed the straightforward approach to prepare mechanically robust lightweight 3D printed materials.
- 15 September 2022
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 307 (11)
Revealing the Combined Nanoconfinement Effect by Soft and Stiff Inclusions in PMMA/Silica CO2 Blown Foams
This study shows the importance of nanoparticle (NP) spatial arrangement on the nucleation, morphology, and properties of nanocomposite foams. It probes CO2 blown PMMA with three types of nanosilica structures with exactly the same chemical composition: aggregates, chain bound clusters, and individually dispersed NPs. A systematic but nontrivial scaling of morphology, glass transition temperature, static and impact mechanical properties, and thermal conductivity is discussed with special regard to the combined nanoconfinement by soft and stiff inclusions. The presented results suggest a limited potential of simultaneous toughening by nanoreinforcement and shear banding, which can draw significant implications for both the fundamental science and industrial practice dealing with nanoreinforced cellular materials.
- 15 September 2022
- Published by Wiley in Macromolecular Materials and Engineering
- Vol. 307 (11)
Revealing the Combined Nanoconfinement Effect by Soft and Stiff Inclusions in PMMA/Silica CO2 Blown Foams
This study shows the importance of nanoparticle (NP) spatial arrangement on the nucleation, morphology, and properties of nanocomposite foams. It probes CO2 blown PMMA with three types of nanosilica structures with exactly the same chemical composition: aggregates, chain bound clusters, and individually dispersed NPs. A systematic but nontrivial scaling of morphology, glass transition temperature, static and impact mechanical properties, and thermal conductivity is discussed with special regard to the combined nanoconfinement by soft and stiff inclusions. The presented results suggest a limited potential of simultaneous toughening by nanoreinforcement and shear banding, which can draw significant implications for both the fundamental science and industrial practice dealing with nanoreinforced cellular materials.
- Open Access
- 15 September 2022
- Published by Elsevier in Polymer Testing
- Vol. 116
Photoactivity, conversion kinetics, nanoreinforcement, post-curing, and electric/dielectric properties of functional 3D printable photopolymer resin filled with bare and alumina-doped ZnO nanoparticles
- 15 September 2022
- Published by Elsevier in Polymer Testing
- Vol. 116
Open AccessPhotoactivity, conversion kinetics, nanoreinforcement, post-curing, and electric/dielectric properties of functional 3D printable photopolymer resin filled with bare and alumina-doped ZnO nanoparticles
- 3 March 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry B
- Vol. 10 (15) , 2889-2898
Anisotropic solid-state PLA foaming templated by crystal phase pre-oriented with 3D printing: cell supporting structures with directional capillary transfer function
Bones represent a superb biomaterial that combines high mechanical stiffness with nutrition delivery to its osteocyte cells through the microscopical Haversian canals and bone canaliculi. Such a structure is hard to reproduce artificially, though. 3D printing delivers an unprecedented shape control of the created objects. Yet the resolution limit of the most common 3D printers is insufficient, lying between tens to hundreds of microns, while more precise 3D printing techniques fail in fabricating larger objects. We present a unique, yet simple and versatile method for preparing hierarchically aligned microporous canals using a biocompatible polymer polylactic acid (PLA) with their structure controlled at the submicron to macro scale. The layout was inspired by the microscopical Haversian canals and bone canaliculi of cortical bone. This procedure takes advantage of the PLA complex crystalline behavior, which was pre-oriented by 3D printing, orientedly crystallized in CO2, foamed, and cryo-shrunk. The canal formation was assessed via WAXS, FTIR spectroscopy, and DSC and complemented by the evaluation of mechanical properties, biocompatibility, and directionally selective capillary transport in the final structure. The fine dimensions of the canals unmatched by the common 3D printing techniques capable of making macroscale objects combined with the abovementioned properties represent promising potential for various applications, such as advanced cell-supporting designs with a built-in nutrition function.
- 3 March 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry B
- Vol. 10 (15) , 2889-2898
Anisotropic solid-state PLA foaming templated by crystal phase pre-oriented with 3D printing: cell supporting structures with directional capillary transfer function
Bones represent a superb biomaterial that combines high mechanical stiffness with nutrition delivery to its osteocyte cells through the microscopical Haversian canals and bone canaliculi. Such a structure is hard to reproduce artificially, though. 3D printing delivers an unprecedented shape control of the created objects. Yet the resolution limit of the most common 3D printers is insufficient, lying between tens to hundreds of microns, while more precise 3D printing techniques fail in fabricating larger objects. We present a unique, yet simple and versatile method for preparing hierarchically aligned microporous canals using a biocompatible polymer polylactic acid (PLA) with their structure controlled at the submicron to macro scale. The layout was inspired by the microscopical Haversian canals and bone canaliculi of cortical bone. This procedure takes advantage of the PLA complex crystalline behavior, which was pre-oriented by 3D printing, orientedly crystallized in CO2, foamed, and cryo-shrunk. The canal formation was assessed via WAXS, FTIR spectroscopy, and DSC and complemented by the evaluation of mechanical properties, biocompatibility, and directionally selective capillary transport in the final structure. The fine dimensions of the canals unmatched by the common 3D printing techniques capable of making macroscale objects combined with the abovementioned properties represent promising potential for various applications, such as advanced cell-supporting designs with a built-in nutrition function.
- Open Access
- 1 December 2021
- Published by Elsevier in Polymer Testing
- Vol. 104
PLA toughening via bamboo-inspired 3D printed structural design
- 1 December 2021
- Published by Elsevier in Polymer Testing
- Vol. 104
Open AccessPLA toughening via bamboo-inspired 3D printed structural design