Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xiaowei Cheng has a total of 16 co-authors. Here are the top co-authors by number of shared publications:

  • Yi Li

    Key Laboratory of Urban Security and Disaster Engineering of Ministry of Education Beijing University of Technology Beijing China

    3 shared publications
  • Xiuli Du

    Key Laboratory of Urban Security and Disaster Engineering of Ministry of Education Beijing University of Technology Beijing China

    2 shared publications
  • Fangfang Liu

    Beijing Key Laboratory of Earthquake Engineering and Structural Retrofit, Beijing University of Technology, Beijing 100124, China

    1 shared publication
  • Hailin Sun

    1 shared publication
  • Haoyou Zhang

    Key Laboratory of Urban Security and Disaster Engineering of Ministry of Education, Beijing University of Technology, Beijing, China

    1 shared publication
  • Hong Guan

    1 shared publication

Latest Publications

  • Shear behavior of reinforced concrete walls under variable axial tension‐compression and cyclic lateral loads

    by Xiaowei Cheng, Jiankang Huang, Nuo Xu, Yi Li, Xiaodong Ji, Xiuli Du

    Under a strong earthquake, the axial force of shear walls in tall buildings may vary from compression to tension, but few studies have been conducted on this. Three low‐aspect‐ratio reinforced concrete (RC) wall specimens subjected to coupled variable axial tension‐compression and lateral load were tested in this study, to investigate the effect of the fluctuating range of axial force and loading histories on the shear behavior of RC walls. The test results indicated that shear‐compression failure occurred under the compressive‐shear loading for all test wall specimens, and no obvious post‐peak strength degradation in tension‐shear loading. The hysteretic curves of test wall specimens were strongly affected by the loading histories; the shear strength and deformation capacity were mainly affected by the fluctuation of axial forces, especially for tension‐shear strength. The equation of ACI 318‐19 and JGJ 3‐2010 conservatively predicted the shear strength of RC walls under the variable axial force, while the equation of ASCE/SEI 43‐05 accurately predicted the shear strength with the mean values of the VTest/VASCE of 0.97 and 0.94 for compression‐shear and tension‐shear strength, respectively. Comparison with an RC wall under constant axial tension revealed that the failure modes of RC walls were strongly dependent on the initial cracking patterns. Finally, a finite element (FE) model was developed, and parametric analyses were carried out to further estimate the effect of variable axial force on the cyclic shear behavior of RC walls.


  • Experimental study of precast concrete walls with replaceable corner components

    by Xiaowei Cheng, Xiaowei Dong, Yi Li, Xinzheng Lu, Xiuli Du

    To improve the seismic resiliency of precast concrete (PC) wall, a type of emulative PC wall with replaceable corner components (RCCs) was developed in this study. The damage of the PC wall was deliberately concentrated in the RCCs, which can be replaced after an earthquake. Four large‐aspect‐ratio specimens (including three PC walls with different tensile strength RCCs, and one monolithic cast‐in‐place reinforced concrete (RC) wall) were tested to investigate the seismic behavior of the PC wall, the replaceability of the RCCs, and comparability of the PC wall with the RC wall. Although flexural failure occurred for the three PC walls, the locations of damage were different. For PC walls with low and moderate tensile strength RCCs, the damage was successfully concentrated in RCCs, while for PC wall with high tensile strength RCCs, the damage was expanded from RCCs to the non‐replaced part of the PC wall. When RCCs had approximately identical tensile strength to the boundary element of RC wall, the performance of the PC wall emulated that of the RC wall. The ultimate drift ratio of the PC walls ranged from 1.7% to 2.2% which is lower than that of 2.7% for the RC wall. The PC wall, before and after replacing RCCs, exhibited approximately identical lateral load, while slight lower initial stiffness. The vertical displacement profiles of wall bottom section were almost linear, and the yielding and peak strength of the PC walls could be reasonably estimated by assuming the wall bottom section remain plane after deformation.


  • Open Access

    Dynamic Mechanical Properties of Rolled Thin-Walled Steel Plates (TWSPs) Used for W-Beam Guardrails under Low and Medium Strain Rates

    by Fangfang Liu, Xiaowei Cheng, Yi Li, Manjuan Yang, Yujing Zhou

    Accurately considering the dynamic mechanical properties of rolled thin-walled steel plates (TWSPs) under low and medium strain rates is the basis of numerical simulations of W-beam guardrails subjected to vehicle impact. Uniaxial tensile tests were conducted on specimens extracted from different locations (flat TWSPs without cold rolling treatment, and the cross-sectional centers and slopes of rolled TWSPs) and under different strain rates (ε˙ = 0.00025, 0.01, and 50 s−1). Based on experimental and numerical results, the cross-sectional center of a rolled TWSP is recommended as the representative sampling location for uniaxial tensile tests. Additional uniaxial tensile tests with wider strain rates of 10, 100, and 200 s−1 were also conducted on specimens at the recommended sampling location (cross-sectional center) of rolled TWSPs. It was found that the Cowper–Symonds model with parameters of C = 40 s−1 and p = 5 recommend by Symonds significantly overestimated the strain rate effects of the rolled TWSP material in the low and medium strain-rate region. The model with calibrated parameters of C = 4814 s−1 and p = 2.9 was recommended for considering the influences of strain rate effects on the dynamic mechanical properties of rolled TWSP at low to medium strain rates.


  • Open Access

    Numerical Modelling of Reinforced Concrete Slender Walls Subjected to Coupled Axial Tension–Flexure

    by Xiaowei Cheng, Haoyou Zhang

    Under strong earthquakes, reinforced concrete (RC) walls in high-rise buildings, particularly in wall piers that form part of a coupled or core wall system, may experience coupled axial tension–flexure loading. In this study, a detailed finite element model was developed in VecTor2 to provide an effective tool for the further investigation of the seismic behaviour of RC walls subjected to axial tension and cyclic lateral loading. The model was verified using experimental data from recent RC wall tests under axial tension and cyclic lateral loading, and results showed that the model can accurately capture the overall response of RC walls. Additional analyses were conducted using the developed model to investigate the effect of key design parameters on the peak strength, ultimate deformation capacity and plastic hinge length of RC walls under axial tension and cyclic lateral loading. On the basis of the analysis results, useful information were provided when designing or assessing the seismic behaviour of RC slender walls under coupled axial tension–flexure loading.