GBGentry Berry

Gentry Berry

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Gentry Berry has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Investigation of the Influence of Data Collection and Analysis Procedures on Aerosol Filtration Model Development

    by Gentry Berry, Alta Knizley, Ivan Beckman, Heejin Cho

    Fibrous air filters are common devices used to remove airborne particles. Their performance is typically measured through their resistance to airflow and captured particle mass. Models describing the evolution of filter performance have been heavily researched; however, the need for improvement remains. Experimental work is irreplaceable in the development of high-fidelity models, yet the estimation of necessary variables is not trivial and may be influenced by selected measurement instruments and analysis methodologies. Therefore, the purpose of this work is to propose a framework to investigate the response of common aerosol measurement instruments, their corresponding analysis methodologies, and the application of their data. A Scanning Mobility Particle Sizer (SMPS) and Laser Aerosol Spectrometer (LAS) were selected for consideration, and their recorded data were compared against baseline measurements. The results of the experiments indicated that the SMPS and LAS yielded a ratio of estimated mass concentrations to the baseline mass concentrations of approximately 1.175 and 0.749, respectively. Regarding the SMPS, it was suggested that the measurable size range, application of a coverage factor, dynamic shape factor, and association between the curve fits and histograms were influential in the final estimates. For the LAS, the application of a curve fit, its association to the histograms, and the selection of the sampling periods were influential. Considering the results, the impact of these factors may not be considered negligible and may skew reproducibility between studies and fossilize confounding factors. Therefore, the proposed methodologies are useful in addressing potential errors in data collection and analysis.

  • Open Access

    Stabilized Electrospun Polyacrylonitrile Fibers for Advancements in Clean Air Technology

    by Ivan P. Beckman, Gentry Berry, Mine Ucak-Astarlioglu, Travis L. Thornell, Heejin Cho, Guillermo Riveros

    Particulate matter air pollution and volatile organic compounds released into the air from the incomplete combustion of fossil fuels and wildfires creates significant damage to human health and the environment. Advances in air filtration and purification technology are needed to mitigate aerosol hazards. This article details an effort to explore the potential benefits of new materials and methods for the production of nonwoven air filtration media through electrospinning and stabilizing polyacrylonitrile fibers. The investigated production methods include electrospinning fibrous matting onto a stainless steel wire mesh and stabilizing the nonwoven media in a chamber furnace. The media is then tested for air filtration penetration and airflow resistance, and the fiber size distribution is measured using scanning electron microscopy. The experimental results show that the electrospun media approaches the performance criteria for airflow resistance and particle capture efficiency of high-efficiency particulate air (HEPA) filter media. Furthermore, performance estimations for electrospun media of increased thickness and for a decreased filtration velocity show potential to exceed the HEPA media resistance and efficiency criteria. Thus, it is suggested that electrospun and stabilized nonwoven fibrous media are candidates as alternatives to traditionally manufactured HEPA media and may potentially benefit modern air filtration technology and reduce hazards associated with particulate matter. Additionally, the authors recommend future exploration into the carbonization and activation of electrospun filter media for the adsorption and mitigation of volatile organic compounds as a secondary benefit, while maintaining high efficiency and low airflow resistance in the removal of particulate matter from aerosol streams.


  • Open Access

    Digital Twin Geometry for Fibrous Air Filtration Media

    by Ivan P. Beckman, Gentry Berry, Heejin Cho, Guillermo Riveros

    Computational modeling of air filtration is possible by replicating nonwoven nanofibrous meltblown or electrospun filter media with digital representative geometry. This article presents a methodology to create and modify randomly generated fiber geometry intended as a digital twin replica of fibrous filtration media. Digital twin replicas of meltblown and electrospun filter media are created using Python scripting and Ansys SpaceClaim. The effect of fiber stiffness, represented by a fiber relaxation slope, is analyzed in relation to resulting filter solid volume fraction and thickness. Contemporary air filtration media may also be effectively modeled analytically and tested experimentally in order to yield valuable information on critical characteristics, such as overall resistance to airflow and particle capture efficiency. An application of the Single Fiber Efficiency model is incorporated in this work to illustrate the estimation of performance for the generated media with an analytical model. The resulting digital twin fibrous geometry compares well with SEM imagery of fibrous filter materials. This article concludes by suggesting adaptation of the methodology to replicate digital twins of other nonwoven fiber mesh applications for computational modeling, such as fiber reinforced additive manufacturing and composite materials.