EKEunjin Kim

Eunjin Kim

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Eunjin Kim has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Unveiling Top Electrode‐Dependent Morphotropic Phase Boundary Mechanisms in Hf 0.2 Zr 0.8 O 2 Thin Films

    by Eunjin Kim, Jihyun Kim, Jaebin Lee, Seokjae Lim, Jiyong Woo

    We investigate the top electrode (TE)‐dependent morphotropic phase boundary (MPB) characteristics in Hf 0.2 Zr 0.8 O 2 films, where orthorhombic and tetragonal phases coexist. Notable MPB behavior is observed exclusively in Hf 0.2 Zr 0.8 O 2 layers with W and Ru TEs on a fixed W bottom electrode (BE) after post‐metallization annealing (PMA). To clarify the mechanism, we track four peaks obtained from capacitance‐voltage (C−V) analysis under various measurement conditions. The W TE/Hf 0.2 Zr 0.8 O 2 /W BE capacitor exhibits two symmetric main peaks associated with MPB motion through the reduced energy barrier between the two phases. At a cryogenic temperature (123 K), these peak voltages shift near 0 V, which facilitates MPB motion. Conversely, the Ru TE/Hf 0.2 Zr 0.8 O 2 /W BE capacitor shows highly asymmetric C−V profiles over a wide temperature range (123–343 K). Physical analyses reveal that the W TE induces finely distributed mixed phases in Hf 0.2 Zr 0.8 O 2 . These numerous phase boundaries lower the phase transition energy and promote MPB motion. In contrast, relatively larger, single‐dominant phases are formed in Hf 0.2 Zr 0.8 O 2 with the Ru TE, which results in fewer phase boundaries, which are inherently unfavorable for MPB activation. Nevertheless, a built‐in potential arising from the work function difference between the Ru TE and W BE lowers the barrier and enables MPB behavior.

  • Open Access

    Enhanced Polarization Switching in HfZrO 2 MFS FeFET Using WO x Interlayer

    by Eunjin Kim, Hyoungjin Park, Jiae Jeong, Jiyong Woo

    We demonstrate that the memory window (MW) of HfZrO2 (HZO)-based ferroelectric field-effect transistors (FeFETs) with an InZnO channel/HZO/W gate stack can be noticeably widened to over 2 V by introducing an amorphous WO2.7 interlayer (IL) into the gate interface. Although an orthorhombic (o-) phase is clearly observed in HZO using microscopic images and diffraction patterns, a narrow MW of 0.5 V is obtained from the FeFET. Unlike those obtained from the HZO FeFET, a large 2 remnant polarization of 19 μC/cm2 and intense diffraction peaks corresponding to the o-phase are obtained from the HZO/WO2.7 FeFET. Surface topology and elemental analyses reveal that most of the phases of HZO can be uniformly transformed into the o-phase by the amorphous WO2.7 IL with a low thermal expansion coefficient of ~1 × 10–6 K–1. In addition, the WO2.7 IL prevents unwanted defect generation at the HZO/W gate interface. Therefore, the number of dipoles in the HZO/WO2.7 IL FeFET participating in switching increases without charge trapping, thereby improving cycling endurance and low-temperature (–150 °C) operation.

  • Open Access

    Evolution of Materials and Device Stacks for HfO 2 ‐Based Ferroelectric Memories

    by Eunjin Kim, Jiyong Woo

    The discovery of ferroelectricity in HfO 2 offering the advantage of nonvolatile polarization switching creates a renewed interest in the semiconductor memory industry. Doped HfO 2 ‐based thin films maintain stable remanent polarization (P r ) at nanometer‐scale thicknesses within back‐end‐of‐line thermal budgets, which makes them an attractive material family for compact ferroelectric capacitors (FeCAPs) and ferroelectric field‐effect transistors (FeFETs) in embedded and in‐memory computing. The orientation of electric dipoles in the HfO 2 layer defines the stored information in FeCAPs and adjusts the electron density in the channel of FeFETs. Therefore, controlling dipole rotation, which is closely linked to P r , plays an important role in achieving reliable memory operation. In this review, we first show the evolution of doped HfO 2 thin films in terms of engineering the ferroelectric orthorhombic phase. Since the ferroelectric HfO 2 layer is deposited onto non‐inert metal electrodes in FeCAPs or semiconductor materials serving as a channel in FeFETs, the reliability characteristics of the ferroelectric memories primarily depend on these interface conditions. Therefore, we second address recent interface engineering strategies tailored to each device configuration.


  • Enhanced reliability of ultrathin IZO channel thin-film transistors via p-type Si doping

    by Hyoungjin Park, Eunjin Kim, Jiae Jeong, Jiyong Woo

    The reliability of indium-zinc-oxide (IZO) channel thin-film transistors (TFTs) was improved by incorporating p-type silicon (p-Si) into the channel layer. Initially, the Mo gate/HfO2 gate dielectric/undoped IZO channel TFT exhibited a threshold voltage (VT) of −3.5 V and a subthreshold swing (SS) of 199 mV/dec. In contrast, doping the IZO channel with p-Si (p-Si:IZO), achieved via co-sputtering with a power of 3 W applied to the p-Si target during deposition, effectively suppressed excess free electron carriers. This modification increased the VT to −2.3 V and improved the SS to 122 mV/dec. X-ray photoelectron spectroscopy analysis revealed an increased O–H bond concentration in the p-Si:IZO channel, suggesting that hydrogen-induced traps, originating from the HfO2 gate dielectric, were passivated. This interpretation is supported by the reduced trap density, estimated at 6.4 × 1013 eV−1 cm−2, extracted from SS measurements. Consequently, the optimized p-Si:IZO channel TFT exhibited robust reliability, with minimal VT shifts of 0.3 and 0.4 V under positive bias stress and positive bias temperature stress at 85 °C, respectively. Furthermore, at cryogenic temperatures (−170 °C), the p-Si:IZO channel TFT achieved a VT of −1.1 V and an SS of 105 mV/dec.

  • Open Access

    Tailoring ferroelectricity in Al:HfO2 capacitors: A comprehensive approach to annealing, electrode selection, and Al dopant distribution

    by Hyoungjin Park, Jiae Jeong, Eunjin Kim, Jiyong Woo

    We systematically investigate the effects of annealing conditions, Al2O3 atomic layer deposition (ALD) cycle number and distribution, and top electrode (TE) material on the ferroelectric switching behavior of 10 nm-thick Al-doped HfO2 (Al:HfO2) films. We perform 150 ALD cycles, comprising HfO2 and Al2O3 sub-cycles, with precise control over the number and distribution of Al2O3 cycles. Post-metallization annealing (PMA) at 600 °C for 3 min induced spontaneous 2 remnant polarization (2Pr) through the combined Al-induced lattice stress and TE-induced mechanical stress, promoting orthorhombic phase formation. Optimization to three Al2O3 cycles within the HfO2 bulk balances polarization enhancement and suppression of oxygen-vacancy-induced leakage, yielding a 2Pr = 3 μC/cm2 and endurance up to 106 cycles. The W electrodes, with a low thermal expansion coefficient and smooth surfaces, enable uniform stress transfer and improved dipole alignment compared to Mo and Ru electrodes. Notably, asymmetric localization of Al2O3 sub-cycles near the lower HfO2 region, combined with TE-induced stress, maximizes uniform stress distribution across the film. As confirmed by positive-up-negative-down measurements, this mechanism activates a higher dipole density and achieves the highest 2Pr = ∼9 μC/cm2 without additional leakage. These findings demonstrate that jointly optimizing thermal treatment, dopant engineering, and electrode selection enhances phase stability and dipole activity in HfO2-based ferroelectrics.


  • Interfacial p-Si doped InZnO ferroelectric FET for enhanced memory window

    by Hyoungjin Park, Jiae Jeong, Eunjin Kim, Seokjae Lim, Jiyong Woo

    Since abundant electrons serve as the primary carriers in n-type oxide semiconductors, dipole-induced electron repulsion is ineffective in increasing the threshold voltage (VT) of oxide channel ferroelectric field-effect transistors (FeFETs), thereby limiting the memory window (MW). To effectively suppress electron participation, we introduce a p-type Si (p-Si) doping technique into the InZnO (IZO) channel through co-sputtering. When the optimal p-Si condition, controlled by adjusting sputtering power, is applied, the remanent polarization obtained from positive-up, negative-down measurements increases to ∼18 μC/cm2 in the HfZrO/p-Si-doped IZO (p-Si:IZO) capacitor. This indicates that the number of electrons in p-Si:IZO, which can pin dipoles, is reduced. This electron annihilation is evidenced by lowered current drivability and an enlarged VT in an oxide transistor with a Mo/HfO2/p-Si:IZO gate stack. However, bulk p-Si doping causes charge trapping in p-Si:IZO FeFETs, restricting MW expansion. To mitigate this trade-off, p-Si doping is selectively performed only at the IZO interface. Consequently, interfacial p-Si:IZO FeFETs exhibit an MW of 2.3 V—twice that of IZO FeFETs—and 1.5 V in DC double-sweep and AC pulse measurements, respectively.


  • WOx Interlayer Engineering for Reliable Polarization in HfZrO2 Ferroelectric Capacitors

    by Eunjin Kim, Hyoungjin Park, Jiae Jeong, Seokjae Lim, Kibong Moon, Jiyong Woo

    Post-metallization annealing, even at a low temperature of $350~^{\circ }$ C, is essential to induce ferroelectricity in HfZrO2 (HZO) capacitors (FeCAPs). However, this process can also generate an unwanted oxide layer at the non-inert electrode interface. Our findings reveal that a thin substoichiometric WOx is formed on top of a W bottom electrode (BE) owing to the scavenging of oxygen ions from HZO. Oxygen vacancies (VOs) generated near the HZO/BE interface cause dipole rotation, rendering the FeCAPs vulnerable to temperature and endurance cycling. We introduce a sputter-deposited amorphous WOx interlayer (IL) at the BE interface and examine the impact on ferroelectric polarization. In the HZO/WO ${}_{{2}.{4}}$ FeCAPs, many VOs in the IL can be clustered during endurance, causing breakdown at $10^{{4}}$ cycles. However, when a nearly stoichiometric WO3 IL is used, the polarization with increased coercive voltage ( ${V}_{c}$ ) is observed only at a low frequency. This indicates that most of the voltage drop occurs across the insulating WO3 IL rather than across HZO, showing weak remnant polarization (Pr). The optimized WO ${}_{{2}.{8}}$ IL suppresses VOs generation, serving as charge trapping sites near the BE interface and promoting the formation of an orthorhombic phase in HZO, enhancing Pr to $29~\mu $ C/cm2 over $10^{{8}}$ cycles. Additionally, unlike the HZO FeCAPs, in which the ferroelectric properties deteriorate at cryogenic temperatures, a Pr greater than $20~\mu $ C/cm2 at 123 K can be achieved using HZO/WO ${}_{{2}.{8}}$ FeCAPs.


  • Open Access

    Optimizing electrochemical and ferroelectric synaptic devices: from material selection to performance tuning

    by Eunjin Kim, Seonuk Jeon, Hyoungjin Park, Jiae Jeong, Hyeonsik Choi, Yunsur Kim, Jihyun Kim, Seokjae Lim, Kibong Moon, Jiyong Woo

    Neuromorphic hardware systems emulate the parallel neural networks of the human brain, and synaptic weight storage elements are crucial for enabling energy-efficient information processing. They must represent multiple data states and be able to be updated analogously. In order to realize highly controllable synaptic devices, replacing the high-k gate dielectric in conventional transistor structures with either solid-electrolytes that facilitate bulk ionic motion or ferroelectric oxide allows for steady adjustment of channel currents in response to gate-voltage signals. This approach, in turn, accelerates backpropagation algorithms used for training neural networks. Furthermore, because the channel current in electrochemical random-access memory (ECRAM) is influenced by the number of mobile ions (e.g. Li+, O2−, H+ or Cu+) passing through the electrolytes, these synaptic device candidates have demonstrated an excellent linear and symmetrical channel current response when updated using an identical pulse scheme. In the latter case, which is known as the ferroelectric field-effect transistor (FeFET), the number of electrons accumulated near the channel rapidly varies with the degree of the alignment of internal dipoles in thin doped ferroelectric HfO2. This leads to a multilevel state. Based on the working principles of these two promising candidates, enabling gate-controlled ion-transport primarily in electrolytes for ECRAM and understanding the relationship between polarization and the ferroelectric layer in FeFETs are crucial to improve their properties. Therefore, this paper aims to present our recent advances, highlighting the engineering approaches and experimental findings related to ECRAM and FeFET for three-terminal synaptic devices.


  • Open Access

    Investigation of Proton Irradiation-Enhanced Device Performances in AlGaN/GaN HEMTs

    by Jeong-Gil Kim, Eunjin Kim, Dong-Seok Kim, Chuyoung Cho, Jung-Hee Lee

    We have studied the effects of proton irradiation on the AlGaN/GaN HEMTs with AlN buffer layer as well as conventional GaN buffer layer. It was found that a short time proton irradiation (~ 50 sec) can promote beneficial effects on device performances, which results in great reduction in the off-state leakage current and the gate leakage current without degrading the output current and transconductance. The pulsed I-V measurement demonstrated that both devices exhibit greatly improved current dispersion characteristics and, particularly, the device with AlN buffer layer shows stronger radiation hardness than that of the device with GaN buffer layer. These interesting results are believed to be due to the hydrogen passivation with thermal annealing effect during the proton irradiation. It is expected that the proper irradiation condition such as fluence, energy, and time is crucial to improve the device performances, rather than to deteriorate the performances.


  • Open Access

    A Simulation Study on the Effects of Interface Charges and Geometry on Vertical GAA GaN Nanowire MOSFET for Low-Power Application

    by Terirama Thingujam, Quan Dai, Eunjin Kim, Jung-Hee Lee

    The effects of interface charges on the performances of gate-all-around (GAA) GaN vertical nanowire MOSFETs with different geometries have been studied. Geometrical effect on the gate current of vertical GAA GaN nanowire MOSFET has also been analysed for the first time. In the ideal condition, the circular geometry nanowire (CGN) MOSFET exhibits the best performance with subthreshold swing (SS) of 62 mV/dec, drain-induced barrier lowering (DIBL) of 14 mV/V, and ON/OFF current ratio ( I ON /I OFF ) of ~10 8 . The triangular or hexagonal geometry nanowire (TGN or HGN) MOSFET suffer from large gate leakage current due to the field enhancement at sidewall corners. It is also known that interface traps at the sidewall surface of vertical nanowires deteriorate the overall device performance. The HGN MOSFET with m-plane sidewall demonstrates the best performance with SS of 69 mV/dec and DIBL of 13 mV/V, while the TGN MOSFET with a-plane sidewall exhibits the worst performance with SS of 112 mV/dec and DIBL of 101 mV/V.