Zhangli Wang
Zhangli Wang has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Daopei Zhu
School of Civil Engineering and Surveying & Mapping Engineering (Nanchang), Jiangxi University of Science and Technology, Ganzhou 341000, China
5 shared publications - Haocheng Yan
School of Civil and Surveying & Mapping Engineering (Nanchang)
2 shared publications - Siyuan Tian
School of Civil and Surveying & Mapping Engineering (Nanchang)
2 shared publications Daopei Zhu
School of Civil and Surveying & Mapping Engineering, Jiangxi University of Science and Technology, Ganzhou, China
1 shared publication- Jiafeng Li
School of Civil and Surveying & Mapping Engineering, Jiangxi University of Science and Technology, Nanchang 330013, China
1 shared publication Lihui Wang
School of Civil and Surveying and Mapping Engineering, Jiangxi University of Science and Technology, Ganzhou, China
1 shared publication
Latest Publications
- Open Access
- 30 October 2023
- Published by Wiley in Shock and Vibration
- Vol. 2023, 1-11
Monitoring Soil-Pile Stripping Damage at Different Temperatures via Piezoelectric Ceramic Sensors
Large temperature differences exist between the winter and summer seasons in different regions of China. Such temperature differences, caused by seasonal changes, may affect the life cycles of piles. Under natural conditions, such as long-term operation under the ambient environment and loads, piles and the surrounding soil undergo peel damage. To study such peel damage between the pile and soil at different temperatures, we installed concrete test piles in soil and subjected them to different temperatures. A crack with a width of 2 cm, depth of 10 cm, and damage range of 90° was applied at the side of the piles. Furthermore, a horizontal impact load was applied near the top of the pile and a piezoelectric ceramic sensor was used to obtain the stress wave response signals. The experimental results reveal that with a decrease in the soil temperature, the amplitude and fluctuation range of the signals received by the piezoelectric sensor decreased. According to the experimental results, in the group with the greatest influence of temperature, keeping other conditions unchanged and setting different crack depths, the horizontal impact load can also be introduced to observe the frequency change. It can be observed that the larger the crack depth, the smaller the frequency. Finally, ABAQUS was used for simulations, whose results were found to be consistent with those of the experiments. This paper describes a method for determining the safety of soil and piles with peel damage at different temperatures, and it also provides a validation of the necessity of holding the rest constant.
- 30 October 2023
- Published by Wiley in Shock and Vibration
- Vol. 2023, 1-11
Open AccessMonitoring Soil-Pile Stripping Damage at Different Temperatures via Piezoelectric Ceramic Sensors
Large temperature differences exist between the winter and summer seasons in different regions of China. Such temperature differences, caused by seasonal changes, may affect the life cycles of piles. Under natural conditions, such as long-term operation under the ambient environment and loads, piles and the surrounding soil undergo peel damage. To study such peel damage between the pile and soil at different temperatures, we installed concrete test piles in soil and subjected them to different temperatures. A crack with a width of 2 cm, depth of 10 cm, and damage range of 90° was applied at the side of the piles. Furthermore, a horizontal impact load was applied near the top of the pile and a piezoelectric ceramic sensor was used to obtain the stress wave response signals. The experimental results reveal that with a decrease in the soil temperature, the amplitude and fluctuation range of the signals received by the piezoelectric sensor decreased. According to the experimental results, in the group with the greatest influence of temperature, keeping other conditions unchanged and setting different crack depths, the horizontal impact load can also be introduced to observe the frequency change. It can be observed that the larger the crack depth, the smaller the frequency. Finally, ABAQUS was used for simulations, whose results were found to be consistent with those of the experiments. This paper describes a method for determining the safety of soil and piles with peel damage at different temperatures, and it also provides a validation of the necessity of holding the rest constant.
- Open Access
- 13 August 2023
- Published by SAGE Publications in Journal of Low Frequency Noise, Vibration and Active Control
- Vol. 43 (1) , 358-370
Study on pile-soil bonding condition based on transient shock response using piezoceramic sensors
The field evaluation of pile-soil combination is a key step in the service life evaluation of pile foundation. However, due to the time-varying nature of pile-soil interaction, there is no efficient method to accurately analyze it. This paper introduces a health monitoring technique for assessing the state of pile-soil bond. The transient vibration of pile-soil coupling was measured by piezoelectric ceramic sensor. In the experiment, the different bond states of pile and soil were simulated by taking clay of different density as an example. A horizontal force is applied to the top of the pile, and the induced stress wave is detected by piezoelectric ceramic intelligent aggregate sensor embedded in the pile. At the same time, taking the artificial separation of pile-soil as an example, the binding state of pile-soil is analyzed, and the influence of different soil conditions on the pile-soil bonding characteristics is studied. An energy index for quantitative evaluation of pile-soil binding quality is proposed. Taking piles buried in two layers of soil with different densities as an example, the effects of soil with different densities on pile-soil bonding characteristics were studied. Experimental and numerical results verified the effectiveness of the proposed method. The three factors influenced the pile-soil coupling. The experimental and numerical results verified the effectiveness of the proposed approach and pave the way for an approach to directly judge whether there is separation between the pile and soil and evaluate the pile safety.
- 13 August 2023
- Published by SAGE Publications in Journal of Low Frequency Noise, Vibration and Active Control
- Vol. 43 (1) , 358-370
Open AccessStudy on pile-soil bonding condition based on transient shock response using piezoceramic sensors
The field evaluation of pile-soil combination is a key step in the service life evaluation of pile foundation. However, due to the time-varying nature of pile-soil interaction, there is no efficient method to accurately analyze it. This paper introduces a health monitoring technique for assessing the state of pile-soil bond. The transient vibration of pile-soil coupling was measured by piezoelectric ceramic sensor. In the experiment, the different bond states of pile and soil were simulated by taking clay of different density as an example. A horizontal force is applied to the top of the pile, and the induced stress wave is detected by piezoelectric ceramic intelligent aggregate sensor embedded in the pile. At the same time, taking the artificial separation of pile-soil as an example, the binding state of pile-soil is analyzed, and the influence of different soil conditions on the pile-soil bonding characteristics is studied. An energy index for quantitative evaluation of pile-soil binding quality is proposed. Taking piles buried in two layers of soil with different densities as an example, the effects of soil with different densities on pile-soil bonding characteristics were studied. Experimental and numerical results verified the effectiveness of the proposed method. The three factors influenced the pile-soil coupling. The experimental and numerical results verified the effectiveness of the proposed approach and pave the way for an approach to directly judge whether there is separation between the pile and soil and evaluate the pile safety.
- Open Access
- 7 April 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-9
Freeze–thaw process of soil between two piles as monitored by piezoelectric ceramic sensor
As the mechanical properties of soil are affected by the moisture content, diameter of soil particles, and the soil temperature, we used piezoelectric ceramic sensors to monitor the freeze–thaw cycle of different soils at different temperatures and different moisture content. By studying the energy attenuation of stress waves propagating in freezing–thawing soil, its mechanical strength was determined. The results showed that the duration of freeze–thaw process was related to soil type and initial water content. For the same water content and larger soil particle size, the received signal amplitude and energy are larger. For the same soil type and higher water content, the received signal amplitude and energy are stronger. This study provides a feasible monitoring method for infrastructure construction in areas with complex geological conditions, such as Qinghai-Tibet frozen soil.
- 7 April 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-9
Open AccessFreeze–thaw process of soil between two piles as monitored by piezoelectric ceramic sensor
As the mechanical properties of soil are affected by the moisture content, diameter of soil particles, and the soil temperature, we used piezoelectric ceramic sensors to monitor the freeze–thaw cycle of different soils at different temperatures and different moisture content. By studying the energy attenuation of stress waves propagating in freezing–thawing soil, its mechanical strength was determined. The results showed that the duration of freeze–thaw process was related to soil type and initial water content. For the same water content and larger soil particle size, the received signal amplitude and energy are larger. For the same soil type and higher water content, the received signal amplitude and energy are stronger. This study provides a feasible monitoring method for infrastructure construction in areas with complex geological conditions, such as Qinghai-Tibet frozen soil.
- Open Access
- 24 November 2022
- Published by Wiley in Journal of Sensors
- Vol. 2022, 1-10
Monitoring Stress State of H-Shape Steel Using Ceramic Piezoelectric Sensor: A Feasibility Study
To monitor the stress state and yield capacity of H-beams across their entire service process, a real-time monitoring method based on the energy signal response of ceramic piezoelectric sensors is proposed in this paper. The method is applied to conduct loading experiments on H-beams under different load values and web heights. Then, the amplitude and energy of the piezoelectric signals under the two working conditions are compared and analyzed, and the finite element analysis results are verified. The experimental results show that the time-domain waveform energy index increases under an increase in web height or load. Taking the H-section steel member with a web height of 10 cm as an example, when the load value is less than 500 kN/m, the energy index increases (on average) by ~10.5% for every 100 kN/m load increase; when the load value exceeds 500 kN/m and is below 675 kN/m (yield load), the same load increases the energy index by ~13.4%. Meanwhile, a 1 cm average increase in web height increases the energy index by ~14.6%. The finite element simulation results indicate that the ceramic piezoelectric sensor load increases under external load increases up to the yielding load. Because the stress state at the sensor location directly determines the stress wave propagation, the critical buckling loads of H-beams can be predicted using the energy index.
- 24 November 2022
- Published by Wiley in Journal of Sensors
- Vol. 2022, 1-10
Open AccessMonitoring Stress State of H-Shape Steel Using Ceramic Piezoelectric Sensor: A Feasibility Study
To monitor the stress state and yield capacity of H-beams across their entire service process, a real-time monitoring method based on the energy signal response of ceramic piezoelectric sensors is proposed in this paper. The method is applied to conduct loading experiments on H-beams under different load values and web heights. Then, the amplitude and energy of the piezoelectric signals under the two working conditions are compared and analyzed, and the finite element analysis results are verified. The experimental results show that the time-domain waveform energy index increases under an increase in web height or load. Taking the H-section steel member with a web height of 10 cm as an example, when the load value is less than 500 kN/m, the energy index increases (on average) by ~10.5% for every 100 kN/m load increase; when the load value exceeds 500 kN/m and is below 675 kN/m (yield load), the same load increases the energy index by ~13.4%. Meanwhile, a 1 cm average increase in web height increases the energy index by ~14.6%. The finite element simulation results indicate that the ceramic piezoelectric sensor load increases under external load increases up to the yielding load. Because the stress state at the sensor location directly determines the stress wave propagation, the critical buckling loads of H-beams can be predicted using the energy index.
- Open Access
- 15 July 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-8
Size, Shape, and Material Effects in Ferroelectric Octahedral Nanoparticles
Composite materials composed of multiferroelectric nanoparticles in dielectric matrixes have attracted enormous attention for their potential applications in developing future functional devices. However, the functionalities of ferroelectric nanoparticles depend on shapes, sizes, and materials. In this paper, a time-dependent Landau-Ginzburg method has been used and combined with a method as the coupled-physics finite-element-method-based simulations are used to illustrate the polarization behavior in isolated BaTiO3 or PbTiO3 octahedral nanoparticles embedded in a dielectric medium, like SrTiO3 (ST, high dielectric permittivity) and amorphous silica (a-SiO2, low dielectric permittivity). The equilibrium polarization topology of the octahedral nanoparticle is strongly affected by the choice of inclusion and the size of matrix materials. Also, there are three equilibrium polarization patterns, i.e., monodomain, vortex-like, and multidomain, because of the various sizes and material parameters combination. There is a critical particle size below which ferroelectricity vanishes in our calculations. This size of the PbTiO3 octahedral nanoparticle is 2.5 and 3.6 nm for high- and low-permittivity matrix materials, respectively. However, this size of the BaTiO3 octahedral nanoparticle is 3.6 nm regardless of the matrix materials.
- 15 July 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-8
Open AccessSize, Shape, and Material Effects in Ferroelectric Octahedral Nanoparticles
Composite materials composed of multiferroelectric nanoparticles in dielectric matrixes have attracted enormous attention for their potential applications in developing future functional devices. However, the functionalities of ferroelectric nanoparticles depend on shapes, sizes, and materials. In this paper, a time-dependent Landau-Ginzburg method has been used and combined with a method as the coupled-physics finite-element-method-based simulations are used to illustrate the polarization behavior in isolated BaTiO3 or PbTiO3 octahedral nanoparticles embedded in a dielectric medium, like SrTiO3 (ST, high dielectric permittivity) and amorphous silica (a-SiO2, low dielectric permittivity). The equilibrium polarization topology of the octahedral nanoparticle is strongly affected by the choice of inclusion and the size of matrix materials. Also, there are three equilibrium polarization patterns, i.e., monodomain, vortex-like, and multidomain, because of the various sizes and material parameters combination. There is a critical particle size below which ferroelectricity vanishes in our calculations. This size of the PbTiO3 octahedral nanoparticle is 2.5 and 3.6 nm for high- and low-permittivity matrix materials, respectively. However, this size of the BaTiO3 octahedral nanoparticle is 3.6 nm regardless of the matrix materials.
- Open Access
- 1 January 2021
- Published by Wiley in Journal of Sensors
- Vol. 2021 (1)
A Feasibility Study on Monitoring Pile‐Soil Bonding Condition Using Piezoceramic Transducer and Horizontal Impact
The in situ evaluation of pile‐soil bonding condition plays an important role for pile safety assessment in its life cycle. However, so far, there is still no fully mature tool to analyze such couplings, since the pile‐soil coupling exhibits complex and time‐varying relationships. This paper innovatively proposes a health monitoring approach to evaluate the bonding status of the soil and pile contact area. An impact method based on a piezoelectric ceramic sensor is proposed to monitor the bond of pile and soil. A horizontal impact was introduced near the top of the pile, and the induced stress waves were detected by the piezoceramic smart aggregate (SA) sensor embedded in the pile. Different crack damage sizes were made between the soil and the pile to investigate the change of the bonding. An energy index was developed to quantitatively evaluate the quality of the bonding as a pile‐soil bonding index. The proposed approach inspired a potential way to directly judge if there is crack damage between the pile and soil and to evaluate pile safety.
- 1 January 2021
- Published by Wiley in Journal of Sensors
- Vol. 2021 (1)
Open AccessA Feasibility Study on Monitoring Pile‐Soil Bonding Condition Using Piezoceramic Transducer and Horizontal Impact
The in situ evaluation of pile‐soil bonding condition plays an important role for pile safety assessment in its life cycle. However, so far, there is still no fully mature tool to analyze such couplings, since the pile‐soil coupling exhibits complex and time‐varying relationships. This paper innovatively proposes a health monitoring approach to evaluate the bonding status of the soil and pile contact area. An impact method based on a piezoelectric ceramic sensor is proposed to monitor the bond of pile and soil. A horizontal impact was introduced near the top of the pile, and the induced stress waves were detected by the piezoceramic smart aggregate (SA) sensor embedded in the pile. Different crack damage sizes were made between the soil and the pile to investigate the change of the bonding. An energy index was developed to quantitatively evaluate the quality of the bonding as a pile‐soil bonding index. The proposed approach inspired a potential way to directly judge if there is crack damage between the pile and soil and to evaluate pile safety.
- Open Access
- 1 January 2018
- Published by Journal of Applied Optics in Journal of Applied Optics
- Vol. 39 (2) , 98-102
Precise axis centering calibration technology for optical lens
- 1 January 2018
- Published by Journal of Applied Optics in Journal of Applied Optics
- Vol. 39 (2) , 98-102
Open AccessPrecise axis centering calibration technology for optical lens