Wenjing Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Wenjing Chen has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Guoqing Gou
Key Laboratory of Advanced Technologies of Materials, Ministry of Education, School of Materials Science and Engineering, Southwest Jiaotong University, Chengdu 610031, China
2 shared publications - Zhenlin Zhang
School of Material Science and Engineering, Southwest Jiaotong University, Chengdu 610031, China
2 shared publications - Bo Tan
School of Materials Science and Engineering, Xihua University, Chengdu 610039, China
1 shared publication - Chen Yang
School of Materials Science and Engineering, Xihua University, Chengdu 610039, China
1 shared publication Huying Yan
1 shared publicationJialing Tang
1 shared publication
Latest Publications
- Open Access
Hydrogen Damage Behavior of X80 Pipeline Steel Under AC Interference
X80 pipeline steel is a key material in the field of oil and gas transportation. Its damage behavior in a hydrogen-filled environment directly affects pipeline safety. In this study, through hydrogen permeation experiments and slow strain rate tensile tests, the electrochemical responses and hydrogen-induced cracking behaviors of X80 base metal and welded joints under hydrogen filling conditions in both AC and DC were systematically compared. The results show that when the base material is filled with hydrogen at 20 mA/cm2 AC, the hydrogen permeation flux is the largest, and the overall hydrogen permeation parameter of the welded joint is lower than that of the base material. High-frequency polarization promotes hydrogen permeation, but anodic corrosion products at high current densities can impede hydrogen entry. The slow strain rate tensile test further confirmed that the mechanical properties of the material declined more significantly under direct current hydrogen charging, and the sensitivity to stress corrosion cracking was higher. Under alternating hydrogen charging conditions, due to the alternating effects of hydrogen charging at the cathode and corrosion at the anode, a relatively low hydrogen embrittlement sensitivity is exhibited.
Open AccessHydrogen Damage Behavior of X80 Pipeline Steel Under AC Interference
X80 pipeline steel is a key material in the field of oil and gas transportation. Its damage behavior in a hydrogen-filled environment directly affects pipeline safety. In this study, through hydrogen permeation experiments and slow strain rate tensile tests, the electrochemical responses and hydrogen-induced cracking behaviors of X80 base metal and welded joints under hydrogen filling conditions in both AC and DC were systematically compared. The results show that when the base material is filled with hydrogen at 20 mA/cm2 AC, the hydrogen permeation flux is the largest, and the overall hydrogen permeation parameter of the welded joint is lower than that of the base material. High-frequency polarization promotes hydrogen permeation, but anodic corrosion products at high current densities can impede hydrogen entry. The slow strain rate tensile test further confirmed that the mechanical properties of the material declined more significantly under direct current hydrogen charging, and the sensitivity to stress corrosion cracking was higher. Under alternating hydrogen charging conditions, due to the alternating effects of hydrogen charging at the cathode and corrosion at the anode, a relatively low hydrogen embrittlement sensitivity is exhibited.
- Open Access
Influence of Heat Treatment on Microstructure and Mechanical Properties of Laser Cladding Coatings
This study investigates the influence of various heat treatment processes on the microstructure and properties of laser cladding Fe314 coatings. The microstructure, phases, and impact fracture morphology of the cladding layer were observed using X-ray diffraction and scanning electron microscopy, among other methods. The hardness and impact performance of the cladding layer were also tested. The results indicated that there was compositional segregation and non-equilibrium microstructure in the untreated cladding layer, with an average microhardness of 368.67 HV and an impact toughness of 27 J, exhibiting quasi-cleavage fracture. The stress-relief annealing treatment resulted in a uniform distribution of M23C6 carbides inside the cladding layer. The pinning effect generated by M23C6 reduced the microhardness by 16.26% and increased the impact toughness to 54 J. The impact fracture surface exhibited ductile fracture. After secondary normalizing and annealing, the microstructure of the cladding layer transformed into a fine single-phase austenite structure, and fine M7C3 carbides precipitated at the grain boundaries. Under the effects of fine grain strengthening and dispersion strengthening, the microhardness of the cladding layer decreased by 38.14%, and the average impact absorbed energy of the specimen was 64 J, showing complete ductile fracture.
Open AccessInfluence of Heat Treatment on Microstructure and Mechanical Properties of Laser Cladding Coatings
This study investigates the influence of various heat treatment processes on the microstructure and properties of laser cladding Fe314 coatings. The microstructure, phases, and impact fracture morphology of the cladding layer were observed using X-ray diffraction and scanning electron microscopy, among other methods. The hardness and impact performance of the cladding layer were also tested. The results indicated that there was compositional segregation and non-equilibrium microstructure in the untreated cladding layer, with an average microhardness of 368.67 HV and an impact toughness of 27 J, exhibiting quasi-cleavage fracture. The stress-relief annealing treatment resulted in a uniform distribution of M23C6 carbides inside the cladding layer. The pinning effect generated by M23C6 reduced the microhardness by 16.26% and increased the impact toughness to 54 J. The impact fracture surface exhibited ductile fracture. After secondary normalizing and annealing, the microstructure of the cladding layer transformed into a fine single-phase austenite structure, and fine M7C3 carbides precipitated at the grain boundaries. Under the effects of fine grain strengthening and dispersion strengthening, the microhardness of the cladding layer decreased by 38.14%, and the average impact absorbed energy of the specimen was 64 J, showing complete ductile fracture.
- Open Access
The Effect of Fatigue Damage on the Corrosion Fatigue Crack Growth Mechanism in A7N01P-T4 Aluminum Alloy
A7N01P-T4 aluminum alloy plates for high-speed trains will experience a certain amount of fatigue damage under alternating loads. Three groups of samples, P0 (no fatigue damage), P1 (loading stress 30 MPa), and P2 (loading stress 70 MPa), were created, and corrosion fatigue crack growth (CFCG) tests were conducted in 3.5 wt.% NaC1 solution. The crack growth rate was found to increase after fatigue damage as the damage degree increased. In addition, the A7N01P-T4 aluminum alloy base metal exhibited obvious secondary cracks and crack bifurcations after fatigue damage. It is believed that fatigue damage causes stress concentration in the material, while a certain degree of stress corrosion cracking occurs during the CFCG growth process. This is because hydrogen (H) easily accumulates and diffuses along the grain boundary, which reduces the strength of the grain boundary, thereby becoming the preferred orientation for crack growth. This explains why the CFCG rate of the material is accelerated following fatigue damage to a certain extent.
Open AccessThe Effect of Fatigue Damage on the Corrosion Fatigue Crack Growth Mechanism in A7N01P-T4 Aluminum Alloy
A7N01P-T4 aluminum alloy plates for high-speed trains will experience a certain amount of fatigue damage under alternating loads. Three groups of samples, P0 (no fatigue damage), P1 (loading stress 30 MPa), and P2 (loading stress 70 MPa), were created, and corrosion fatigue crack growth (CFCG) tests were conducted in 3.5 wt.% NaC1 solution. The crack growth rate was found to increase after fatigue damage as the damage degree increased. In addition, the A7N01P-T4 aluminum alloy base metal exhibited obvious secondary cracks and crack bifurcations after fatigue damage. It is believed that fatigue damage causes stress concentration in the material, while a certain degree of stress corrosion cracking occurs during the CFCG growth process. This is because hydrogen (H) easily accumulates and diffuses along the grain boundary, which reduces the strength of the grain boundary, thereby becoming the preferred orientation for crack growth. This explains why the CFCG rate of the material is accelerated following fatigue damage to a certain extent.
- Open Access
Microstructure and Fatigue of EA4T Steel in Laser Cladding Remanufacturing
EA4T steel has been widely used in the manufacture of railway axles. Laser cladding remanufacturing technology has been used to repair railway axles, and the failure behaviors of railway axles has been studied. In this work, a class of original FeCrNiMo alloy layers that contain rare-earth elements was successfully fabricated through a laser cladding technique on EA4T steel substrates. The microstructure and elemental distribution of the cladding layers were analyzed through scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA). Simultaneously, the microhardness, bond strength and fatigue properties of different samples were determined. The results indicated that the phase composition of the cladding layer was mainly martensite. The grains in the cladding layer were gradually refined with an increase in the distance from the interface, and the chemical composition distribution was more uniform. At the same time, the bonding property of the cladding layer and matrix was good, and the fatigue strength of the sample was improved.
Open AccessMicrostructure and Fatigue of EA4T Steel in Laser Cladding Remanufacturing
EA4T steel has been widely used in the manufacture of railway axles. Laser cladding remanufacturing technology has been used to repair railway axles, and the failure behaviors of railway axles has been studied. In this work, a class of original FeCrNiMo alloy layers that contain rare-earth elements was successfully fabricated through a laser cladding technique on EA4T steel substrates. The microstructure and elemental distribution of the cladding layers were analyzed through scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron probe microanalysis (EPMA). Simultaneously, the microhardness, bond strength and fatigue properties of different samples were determined. The results indicated that the phase composition of the cladding layer was mainly martensite. The grains in the cladding layer were gradually refined with an increase in the distance from the interface, and the chemical composition distribution was more uniform. At the same time, the bonding property of the cladding layer and matrix was good, and the fatigue strength of the sample was improved.