LNLuong Lam Nguyen

Luong Lam Nguyen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Luong Lam Nguyen has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Direct Isolation of Carboxylated Cellulose Nanocrystals from Lignocellulose Source

    by Thai Anh Do, Luong Lam Nguyen, Thuy Khue Nguyen Thi, Van Quyen Nguyen

    In this study, we report an effective, one-step chemical treatment to directly isolate carboxylated cellulose nanocrystals (CCNCs) from a lignocellulosic source using a mixture of peracetic acid and 10% H2SO4 solution. We used infrared spectroscopy, X-ray diffraction, dynamic light scattering, atomic force microscopy, and scanning electron microscopy to characterize all the materials. The obtained CCNCs exhibited needle-like shapes with a width of 10–50 nm and a length of 200–500 nm, a high crystalline index (71.3%), and a high content of -COOH groups (~1.405 mmol/g), with a zeta potential value of −48.5 mV. We attributed this to the cooperative effect of strong oxidative agent and strong acid, which makes the removal of all components occur simultaneously in parallel with the partial hydrolysis of amorphous cellulose regions. Our study opens a new, simple approach to directly isolate cellulose nanocrystals from a lignocellulosic source.


  • Open Access

    On the Degradation of Glyphosate by Photocatalysis Using TiO2/Biochar Composite Obtained from the Pyrolysis of Rice Husk

    by Phuong Thu Le, Duy Ngoc Le, Thi Hue Nguyen, Huyen Thuong Bui, Le Anh Pham, Luong Lam Nguyen, Quoc Son Nguyen, Thu Phuong Nguyen, Thu Hien Dang, Thi Thuy Duong, et al.

    In this study, titanium dioxide (TiO2) nanoparticles are immobilized onto rice husk biochar (RHB), as a porous support, for the photodegradation of glyphosate under UV light irradiation. The TiO2/RHB composites are prepared by pyrolysis and the sol-gel method. The SEM, XRD, EDX, and FT-IR results confirm the graphene structure of RHB and the formation of 10.61 nm TiO2 nanoparticles on the catalyst support. The effects of operating conditions, including catalyst dosage (3 g L−1, 5 g L−1, 10 g L−1, and 20 g L−1) and different illumination conditions (9 W lamp, 2 × 9 W lamps), on the removal of glyphosate from aqueous solutions were investigated. The photodegradation efficiency of 15 mg L−1 of commercial glyphosate was up to 99% after 5 h of irradiation at pH 3.0, with a TiO2/RHB dosage of 10 g L−1. However, the mineralization efficiency under this condition was lower than the decomposition efficiency of glyphosate, proving the partial degradation of glyphosate into AMPA and other metabolites after 5 h of reaction.


  • Open Access

    Confinement Effect of Plasmon for the Fabrication of Interconnected AuNPs through the Reduction of Diazonium Salts

    by Luong-Lam Nguyen, Quang-Hai Le, Van-Nhat Pham, Mathieu Bastide, Sarra Gam-Derouich, Van-Quynh Nguyen, Jean-Christophe Lacroix

    This paper describes a rapid bottom-up approach to selectively functionalize gold nanoparticles (AuNPs) on an indium tin oxide (ITO) substrate using the plasmon confinement effect. The plasmonic substrates based on a AuNP-free surfactant were fabricated by electrochemical deposition. Using this bottom-up technique, many sub-30 nm spatial gaps between the deposited AuNPs were randomly generated on the ITO substrate, which is difficult to obtain with a top-down approach (i.e., E-beam lithography) due to its fabrication limits. The 4-Aminodiphenyl (ADP) molecules were grafted directly onto the AuNPs through a plasmon-induced reduction of the 4-Aminodiphenyl diazonium salts (ADPD). The ADP organic layer preferentially grew in the narrow gaps between the many adjacent AuNPs to create interconnected AuNPs. This novel strategy opens up an efficient technique for the localized surface modification at the nanoscale over a macroscopic area, which is anticipated to be an advanced nanofabrication technique.