Gang Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Gang Liu has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Yichen Li
School of Petroleum Engineering, China University of Petroleum (East China), Qingdao 266580, China
3 shared publicationsGang Wang
School of Petroleum Engineering
2 shared publicationsKai Wang
School of Petroleum Engineering, China University of Petroleum (East China), Qingdao 266580, China
2 shared publications- Kai Wang
China University of Petroleum (East China)
2 shared publications Yinan Hu
School of Petroleum Engineering, China University of Petroleum (East China), Qingdao 266580, China
2 shared publications- Gang Wang
School of Petroleum Engineering, China University of Petroleum (East China), Qingdao, China
1 shared publication
Latest Publications
- Open Access
Tripability Analysis of Casing Strings in Directional Wells Using the Continuous Beam-Column and Buckling Theory
Hindered casing strings are often encountered in unconventional oil and gas exploration during the casing running process. This not only increases the operating costs and time but can also lead to downhole accidents and even abandonment in serious cases. Due to various assumptions, the calculation results of the existing soft models and hard models are different, which causes confusion for field operators when taking friction reduction measures. Moreover, a lowering force is often applied to assist hindered casing string running in a drilling field. However, its application is mainly based on work experience and lacks mechanistic analysis and theoretical guidance. Thus, in this study, a simulation model for the analysis of casing string tripability in a directional well was established and the model was combined with the continuous beam-column theory and buckling theory. The model was used to study how various factors including the friction coefficient, drilling fluid density, and casing diameter could affect the lowering force required when a casing string was hindered by buckling. The results showed that the maximum lowering force and the maximum effective lowering force decreased with the increase in the friction coefficient and the performance of the drilling fluid could be adjusted rapidly, which would be beneficial for ensuring that the casing string could be tripped smoothly by applying a lowering force. The increase in the drilling fluid density caused the maximum lowering force and the maximum effective lowering force to decrease, which was not conducive to hindered casing string running. The larger the casing diameter was, the greater the maximum lowering force and the maximum effective lowering force were. It was more convenient to apply a lowering force for a casing with a large diameter. In addition, the improved model could identify whether the casing string was in contact with the upper or lower borehole walls. Through finite element method verification, the prediction was in line with the actual casing running operation and the improved model has the smallest prediction error, i.e., 6.58%, compared with the existing models. Therefore, the improved model might provide necessary theoretical guidance for casing running operations in directional wells.
Open AccessTripability Analysis of Casing Strings in Directional Wells Using the Continuous Beam-Column and Buckling Theory
Hindered casing strings are often encountered in unconventional oil and gas exploration during the casing running process. This not only increases the operating costs and time but can also lead to downhole accidents and even abandonment in serious cases. Due to various assumptions, the calculation results of the existing soft models and hard models are different, which causes confusion for field operators when taking friction reduction measures. Moreover, a lowering force is often applied to assist hindered casing string running in a drilling field. However, its application is mainly based on work experience and lacks mechanistic analysis and theoretical guidance. Thus, in this study, a simulation model for the analysis of casing string tripability in a directional well was established and the model was combined with the continuous beam-column theory and buckling theory. The model was used to study how various factors including the friction coefficient, drilling fluid density, and casing diameter could affect the lowering force required when a casing string was hindered by buckling. The results showed that the maximum lowering force and the maximum effective lowering force decreased with the increase in the friction coefficient and the performance of the drilling fluid could be adjusted rapidly, which would be beneficial for ensuring that the casing string could be tripped smoothly by applying a lowering force. The increase in the drilling fluid density caused the maximum lowering force and the maximum effective lowering force to decrease, which was not conducive to hindered casing string running. The larger the casing diameter was, the greater the maximum lowering force and the maximum effective lowering force were. It was more convenient to apply a lowering force for a casing with a large diameter. In addition, the improved model could identify whether the casing string was in contact with the upper or lower borehole walls. Through finite element method verification, the prediction was in line with the actual casing running operation and the improved model has the smallest prediction error, i.e., 6.58%, compared with the existing models. Therefore, the improved model might provide necessary theoretical guidance for casing running operations in directional wells.
- Open Access
Experimental Investigations of Offshore Sand Production Monitoring Based on the Analysis of Vibration in Response to Weak Shocks
Sand production is a problem that is often encountered in unconventional oil and gas exploitation and that is difficult to effectively solve. Accurate online monitoring of sand production is one of the keys to ensuring the safety and long-term production of oil wells as well as efficient production throughout the life cycle of production wells. This paper proposes a method for monitoring sand production in offshore oil wells that is based on the vibration response characteristics of sand-carrying fluid flow impinging on the pipe wall. This method uses acceleration sensors to obtain the weak vibration response characteristics of sand particles impinging on the pipe wall on a two-dimensional time-frequency plane. The time-frequency parameters are further optimized, and the ability to identify weakly excited vibration signals of sand particles in the fluid stream is enhanced. The difference between the impact response of the sand particles and the impact response of the fluid flow to the pipe wall is identified, and corresponding indoor verification experiments are carried out. Under different sand contents, particle sizes, and flow rates (sand content 0-2, sand particle size 96-212μm, and flow velocity 1-3m/s), the impact response frequency of sand particles to the pipe wall exhibits good consistency. The characteristic frequency band of sand impacting the pipe wall is 30-50kHz. A statistical method is used to establish the response law of the noise signal of the fluid. Based on this knowledge, a real-time calculation model of sand production in offshore oil wells is constructed, and the effectiveness of this model is verified. Finally, a field test is carried out with a self-developed sand production signal dynamic time-frequency response software system on 4 wells of an oil production platform in the Bohai Sea. This system can effectively distinguish sand-producing wells from non-sand-producing wells. The dynamic time-frequency response, field test results, and actual laboratory results are consistent, verifying the effectiveness of the method proposed in this paper and further providing a theory for improving the effectiveness of the sand production monitoring method under complex multiphase flow conditions. This study also provides technical guidance for the industrial application of sand production monitoring devices in offshore oil wells.
Open AccessExperimental Investigations of Offshore Sand Production Monitoring Based on the Analysis of Vibration in Response to Weak Shocks
Sand production is a problem that is often encountered in unconventional oil and gas exploitation and that is difficult to effectively solve. Accurate online monitoring of sand production is one of the keys to ensuring the safety and long-term production of oil wells as well as efficient production throughout the life cycle of production wells. This paper proposes a method for monitoring sand production in offshore oil wells that is based on the vibration response characteristics of sand-carrying fluid flow impinging on the pipe wall. This method uses acceleration sensors to obtain the weak vibration response characteristics of sand particles impinging on the pipe wall on a two-dimensional time-frequency plane. The time-frequency parameters are further optimized, and the ability to identify weakly excited vibration signals of sand particles in the fluid stream is enhanced. The difference between the impact response of the sand particles and the impact response of the fluid flow to the pipe wall is identified, and corresponding indoor verification experiments are carried out. Under different sand contents, particle sizes, and flow rates (sand content 0-2, sand particle size 96-212μm, and flow velocity 1-3m/s), the impact response frequency of sand particles to the pipe wall exhibits good consistency. The characteristic frequency band of sand impacting the pipe wall is 30-50kHz. A statistical method is used to establish the response law of the noise signal of the fluid. Based on this knowledge, a real-time calculation model of sand production in offshore oil wells is constructed, and the effectiveness of this model is verified. Finally, a field test is carried out with a self-developed sand production signal dynamic time-frequency response software system on 4 wells of an oil production platform in the Bohai Sea. This system can effectively distinguish sand-producing wells from non-sand-producing wells. The dynamic time-frequency response, field test results, and actual laboratory results are consistent, verifying the effectiveness of the method proposed in this paper and further providing a theory for improving the effectiveness of the sand production monitoring method under complex multiphase flow conditions. This study also provides technical guidance for the industrial application of sand production monitoring devices in offshore oil wells.
- 18 June 2020
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 25 (06) , 3200-3216
Time-Dependent Compressibility of Crude Oil in Gelled State Measured by a New Apparatus
Compressibility is a basic property of gelled crude oil, which was always regarded as a constant in the unsteady-pipe-flow process. In this article, the compressibility of gelled crude oil was accurately measured, and some new characteristics were discovered by a new apparatus that was developed using a special sealing method consisting of an elastic film and the Newtonian fluid. There was no leakage in the special hermetical method, and the unexpected seal-ring deformation of the piston in the traditional compression apparatus was also well-avoided. Using the new apparatus, compressibility of the gelled crude oil was tested and it was found that the compressibility of gelled crude oil is strongly time dependent.
- 18 June 2020
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 25 (06) , 3200-3216
Time-Dependent Compressibility of Crude Oil in Gelled State Measured by a New Apparatus
Compressibility is a basic property of gelled crude oil, which was always regarded as a constant in the unsteady-pipe-flow process. In this article, the compressibility of gelled crude oil was accurately measured, and some new characteristics were discovered by a new apparatus that was developed using a special sealing method consisting of an elastic film and the Newtonian fluid. There was no leakage in the special hermetical method, and the unexpected seal-ring deformation of the piston in the traditional compression apparatus was also well-avoided. Using the new apparatus, compressibility of the gelled crude oil was tested and it was found that the compressibility of gelled crude oil is strongly time dependent.
- 1 June 2019
- Published by Elsevier in Powder Technology
- Vol. 352, 227-239
Vibration multisensor fusion method for the identification and characterization of sand particles in dispersions of oil in water flow
- 1 June 2019
- Published by Elsevier in Powder Technology
- Vol. 352, 227-239
Vibration multisensor fusion method for the identification and characterization of sand particles in dispersions of oil in water flow
- 1 May 2015
- Published by Elsevier in Powder Technology
- Vol. 276, 183-192
Vibration sensor approaches for sand detection in oil–water–sand multiphase flow
- 1 May 2015
- Published by Elsevier in Powder Technology
- Vol. 276, 183-192
Vibration sensor approaches for sand detection in oil–water–sand multiphase flow