Ajit Panesar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Ajit Panesar has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Ricky D. Wildman
University of Nottingham
3 shared publications - Adedeji Aremu
University of Nottingham
2 shared publications Bohan Peng
2 shared publications- Christopher Tuck
Centre for Additive Manufacturing, Faculty of Engineering, University of Nottingham, Jubilee Campus, Nottingham NG8 1BB, U.K.
2 shared publications I.A. Ashcroft
2 shared publicationsIan Ashcroft
2 shared publications
Latest Publications
- Open Access
- 3 November 2026
- Published by Springer Nature in Research Square
Generative design for additive manufacturing through data-free optimization-derived neural weight subspaces
Generative design (GD) enables exploration of diverse shape variants that exhibit trade-offs among competing design objectives related to part manufacturability and performance, offering a transformational approach towards automated part design for advanced additive manufacturing (AM). However, existing GD methods often derive design diversity either from large datasets of existing designs or through topological modifications, limiting their applicability to data-scarce engineering problems, particularly for complex parts where manufacturability and preservation of topology and geometric features are critical. In this work, we present a training-free generative design framework that leverages the optimisation trajectory of a single neural field-based shape optimisation to represent and explore neural field variants within a low-dimensional neural weight subspace. Our design space exploration is realised through a Langevin diffusion-inspired stochastic process with energy-conditioned guidance, enabling the generation of constraint-satisfying shape variants that provide distinct objective trade-offs. The framework generalises across geometrically and topologically diverse complex parts, including freeform geometries with intricate surface features and non-trivial topology. We validate the method through simulations and physical additive manufacturing experiments, demonstrating support-free 3D printing of the generated shape variants and establishing a data-free route towards manufacturability-aware generative design for complex parts.
- 3 November 2026
- Published by Springer Nature in Research Square
Open AccessGenerative design for additive manufacturing through data-free optimization-derived neural weight subspaces
Generative design (GD) enables exploration of diverse shape variants that exhibit trade-offs among competing design objectives related to part manufacturability and performance, offering a transformational approach towards automated part design for advanced additive manufacturing (AM). However, existing GD methods often derive design diversity either from large datasets of existing designs or through topological modifications, limiting their applicability to data-scarce engineering problems, particularly for complex parts where manufacturability and preservation of topology and geometric features are critical. In this work, we present a training-free generative design framework that leverages the optimisation trajectory of a single neural field-based shape optimisation to represent and explore neural field variants within a low-dimensional neural weight subspace. Our design space exploration is realised through a Langevin diffusion-inspired stochastic process with energy-conditioned guidance, enabling the generation of constraint-satisfying shape variants that provide distinct objective trade-offs. The framework generalises across geometrically and topologically diverse complex parts, including freeform geometries with intricate surface features and non-trivial topology. We validate the method through simulations and physical additive manufacturing experiments, demonstrating support-free 3D printing of the generated shape variants and establishing a data-free route towards manufacturability-aware generative design for complex parts.
- Open Access
- 24 May 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 125
Advancing multi-material laser powder bed fusion through topology optimized design
- 24 May 2026
- Published by Elsevier in Additive Manufacturing
- Vol. 125
Open AccessAdvancing multi-material laser powder bed fusion through topology optimized design
- Open Access
- 1 September 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 110
Multi-layer thermal history prediction framework for directed energy deposition based on extended physics-informed neural networks (XPINN)
- 1 September 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 110
Open AccessMulti-layer thermal history prediction framework for directed energy deposition based on extended physics-informed neural networks (XPINN)
- Open Access
- 18 February 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 101
Smooth 3D transition cell generation based on latent space arithmetic
- 18 February 2025
- Published by Elsevier in Additive Manufacturing
- Vol. 101
Open AccessSmooth 3D transition cell generation based on latent space arithmetic
- Open Access
- 31 October 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 95
Multi-layer thermal simulation using physics-informed neural network
- 31 October 2024
- Published by Elsevier in Additive Manufacturing
- Vol. 95
Open AccessMulti-layer thermal simulation using physics-informed neural network
- Open Access
- 28 May 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-14
Multidisciplinary design optimisation of lattice-based battery housing for electric vehicles
Batteries with high energy densities become essential with the increased uptake of electric vehicles. Battery housing, a protective casing encapsulating the battery, must fulfil competing engineering requirements of high stiffness and effective thermal management whilst being lightweight. In this study, a graded lattice design framework is developed based on topology optimisation to effectively tackle the multidisciplinary objectives associated with battery housing. It leverages the triply periodic minimal surfaces lattices, aiming for high mechanical stiffness and efficient heat dissipation considering heat conduction and convection. The effectiveness of the proposed framework was demonstrated through the battery housing design, showcasing its ability to address multidisciplinary objectives as evidenced by the analysis of the Pareto front. This study identifies the potential of lattices in lightweight applications incorporating multiphysics and offers an efficient lattice design framework readily extended to other engineering challenges.
- 28 May 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-14
Open AccessMultidisciplinary design optimisation of lattice-based battery housing for electric vehicles
Batteries with high energy densities become essential with the increased uptake of electric vehicles. Battery housing, a protective casing encapsulating the battery, must fulfil competing engineering requirements of high stiffness and effective thermal management whilst being lightweight. In this study, a graded lattice design framework is developed based on topology optimisation to effectively tackle the multidisciplinary objectives associated with battery housing. It leverages the triply periodic minimal surfaces lattices, aiming for high mechanical stiffness and efficient heat dissipation considering heat conduction and convection. The effectiveness of the proposed framework was demonstrated through the battery housing design, showcasing its ability to address multidisciplinary objectives as evidenced by the analysis of the Pareto front. This study identifies the potential of lattices in lightweight applications incorporating multiphysics and offers an efficient lattice design framework readily extended to other engineering challenges.
- Open Access
Effect of Manufacture-Induced Interfaces on the Tensile Properties of 3D Printed Polyamide and Short Carbon Fibre-Reinforced Polyamide Composites
This study aims to elucidate the structure–property–process relationship of 3D printed polyamide and short carbon fibre-reinforced polyamide composites. The macroscopic properties (tensile modulus) of the 3D printed samples are quantitatively correlated to the printing process-induced intrinsic microstructure with multiple interfaces. The samples were printed with different layer thicknesses (0.1, 0.125 and 0.2 mm) to obtain the varied number of interface densities (number of interfaces per unit sample thickness). The result shows that the printed short carbon fibre-reinforced polyamide composites had inferior partially bonded interfaces compared to the printed polyamide, and consequently exhibited interface-dependent elastic performance. The tensile modulus of 3 mm thick composites decreased up to 18% as a function of interface density, whilst the other influencing aspects including porosity, crystallinity and fibre volume fraction (9%) were the same. Injection moulding was also employed to fabricate samples without induced interfaces, and their tensile properties were used as a benchmark. Predictions based on the shear-lag model were in close agreement (<5%) with the experimental data for the injection-moulded composites, whereas the tensile modulus of the printed composites was up to 38% lower than the predicted modulus due to the partial bonded interfaces.
Open AccessEffect of Manufacture-Induced Interfaces on the Tensile Properties of 3D Printed Polyamide and Short Carbon Fibre-Reinforced Polyamide Composites
This study aims to elucidate the structure–property–process relationship of 3D printed polyamide and short carbon fibre-reinforced polyamide composites. The macroscopic properties (tensile modulus) of the 3D printed samples are quantitatively correlated to the printing process-induced intrinsic microstructure with multiple interfaces. The samples were printed with different layer thicknesses (0.1, 0.125 and 0.2 mm) to obtain the varied number of interface densities (number of interfaces per unit sample thickness). The result shows that the printed short carbon fibre-reinforced polyamide composites had inferior partially bonded interfaces compared to the printed polyamide, and consequently exhibited interface-dependent elastic performance. The tensile modulus of 3 mm thick composites decreased up to 18% as a function of interface density, whilst the other influencing aspects including porosity, crystallinity and fibre volume fraction (9%) were the same. Injection moulding was also employed to fabricate samples without induced interfaces, and their tensile properties were used as a benchmark. Predictions based on the shear-lag model were in close agreement (<5%) with the experimental data for the injection-moulded composites, whereas the tensile modulus of the printed composites was up to 38% lower than the predicted modulus due to the partial bonded interfaces.
- 5 October 2022
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 145 (1)
Predictions of the Elastic–Plastic Compressive Response of Functionally Graded Polymeric Composite Lattices Manufactured by Three-Dimensional Printing
We use three-dimensional printing to manufacture lattices with uniform and graded relative density, made from a composite parent material comprising a nylon matrix reinforced by short carbon fibers. The elastic–plastic compressive response of these solids is measured up to their densification regime. Data from experiments on the lattices with uniform relative density are used to deduce the dependence of their elastic–plastic homogenized constitutive response on their relative density, in the range 0.2–0.8. These data are used to calibrate finite element (FE) simulations of the compressive response of functionally graded lattices (FGLs), which are found in good agreement with the corresponding measurements, capturing the salient features of the measured stress versus strain responses. This exercise is repeated for two lattice topologies (body-centered cubic and Schwarz-P). The phenomenological constitutive models produced in this study can be used in topology optimization to maximize the performance of 3D-printed FGLs components in terms of stiffness, strength, or energy absorption.
- 5 October 2022
- Published by ASME International in Journal of Engineering Materials and Technology
- Vol. 145 (1)
Predictions of the Elastic–Plastic Compressive Response of Functionally Graded Polymeric Composite Lattices Manufactured by Three-Dimensional Printing
We use three-dimensional printing to manufacture lattices with uniform and graded relative density, made from a composite parent material comprising a nylon matrix reinforced by short carbon fibers. The elastic–plastic compressive response of these solids is measured up to their densification regime. Data from experiments on the lattices with uniform relative density are used to deduce the dependence of their elastic–plastic homogenized constitutive response on their relative density, in the range 0.2–0.8. These data are used to calibrate finite element (FE) simulations of the compressive response of functionally graded lattices (FGLs), which are found in good agreement with the corresponding measurements, capturing the salient features of the measured stress versus strain responses. This exercise is repeated for two lattice topologies (body-centered cubic and Schwarz-P). The phenomenological constitutive models produced in this study can be used in topology optimization to maximize the performance of 3D-printed FGLs components in terms of stiffness, strength, or energy absorption.
- Open Access
- 19 December 2019
- Published by Springer Nature in JOM
- Vol. 72 (3) , 1292-1298
Mechanical Performance of Additively Manufactured Fiber-Reinforced Functionally Graded Lattices
Latticing has become a common design practice in additive manufacturing (AM) and represents a key lightweighting strategy to date. Functional graded lattices (FGLs) have recently gained immense traction in the AM community, offering a unique way of tailoring the structural performance. This paper constitutes the first ever investigation on the combination of graded strut- and surface-based lattices with fiber-reinforced AM to further increase the performance-to-weight ratio. The energy absorption behavior of cubic lattice specimens composed of body-centered cubic and Schwarz-P unit cells with different severities of grading but the same mass, considered for uniaxial compression testing and printed by fused deposition modelling of short fiber-reinforced nylon, were investigated. The results elucidate that grading affects the energy absorption capability and deformation behavior of these lattice types differently. These findings can provide engineers with valuable insight into the properties of FGLs, aiding targeted rather than expertise-driven utilization of lattices in design for AM.
- 19 December 2019
- Published by Springer Nature in JOM
- Vol. 72 (3) , 1292-1298
Open AccessMechanical Performance of Additively Manufactured Fiber-Reinforced Functionally Graded Lattices
Latticing has become a common design practice in additive manufacturing (AM) and represents a key lightweighting strategy to date. Functional graded lattices (FGLs) have recently gained immense traction in the AM community, offering a unique way of tailoring the structural performance. This paper constitutes the first ever investigation on the combination of graded strut- and surface-based lattices with fiber-reinforced AM to further increase the performance-to-weight ratio. The energy absorption behavior of cubic lattice specimens composed of body-centered cubic and Schwarz-P unit cells with different severities of grading but the same mass, considered for uniaxial compression testing and printed by fused deposition modelling of short fiber-reinforced nylon, were investigated. The results elucidate that grading affects the energy absorption capability and deformation behavior of these lattice types differently. These findings can provide engineers with valuable insight into the properties of FGLs, aiding targeted rather than expertise-driven utilization of lattices in design for AM.
- 18 November 2019
- Published by IOP Publishing in Multifunctional Materials
- Vol. 2 (4) , 045001
Optimized microstructures for multifunctional structural electrolytes
Multifunctional structural materials offer compelling opportunities to realize highly efficient products. However, the need to fulfil disparate functions generates intrinsically conflicting physical property demands. One attractive strategy is to form a bi-continuous architecture of two disparate phases, each addressing a distinct physical property. For example, structural polymer electrolytes combine rigid and ion-conducting phases to deliver the required mechanical and electrochemical performance. Here, we present a general methodology, based on topology optimization, to identify optimal microstructures for particular design considerations. The numerical predictions have been successfully validated by experiments using 3D printed specimens. These architectures are directly relevant to multifunctional structural composites whilst the methodology can easily be extended to identify optimal microstructural designs for other multifunctional material embodiments.
- 18 November 2019
- Published by IOP Publishing in Multifunctional Materials
- Vol. 2 (4) , 045001
Optimized microstructures for multifunctional structural electrolytes
Multifunctional structural materials offer compelling opportunities to realize highly efficient products. However, the need to fulfil disparate functions generates intrinsically conflicting physical property demands. One attractive strategy is to form a bi-continuous architecture of two disparate phases, each addressing a distinct physical property. For example, structural polymer electrolytes combine rigid and ion-conducting phases to deliver the required mechanical and electrochemical performance. Here, we present a general methodology, based on topology optimization, to identify optimal microstructures for particular design considerations. The numerical predictions have been successfully validated by experiments using 3D printed specimens. These architectures are directly relevant to multifunctional structural composites whilst the methodology can easily be extended to identify optimal microstructural designs for other multifunctional material embodiments.