DTDmytro Tregubov

Dmytro Tregubov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dmytro Tregubov has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    ПРОЦЕСИ ПРИПИНЕННЯ САМОНАГРІВАННЯ ПОШКОДЖЕНИХ ЛІТІЙ-ІОННИХ АКУМУЛЯТОРІВ ПОДАВАННЯМ ВОДИ

    by Дмитро Трегубов, Артем Майборода, Єгор Турбін, Віталій Нуянзін, Дмитро Журбинський

    Об'єктом дослідження є аналіз побудови, принципів роботи та механізмів теплового розгону літій-іонних акумуляторів; увага зосереджена на їх перевагах та недоліках, матеріалах розчинників та електродів, що використовуються, складі газової фази електродних реакцій та особливостях пожежної небезпеки. Узагальнено перебіг процесів, що спостерігаються на основних стадіях теплового розгону акумуляторів. Розроблено методологію та зібрано установку для дослідження процесів теплового розгону пошкодженого акумулятора та його гасіння. Визначено типові зовнішні механічні пошкодження акумулятора, що призводять до неконтрольованого теплового розгону. Відповідність температурного режиму процесу самонагрівання акумулятора стадіям теплового розгону визначається на основі даних вимірювання температури та візуальних спостережень. Розглянуто набір можливих хімічних реакцій, що викликають інтенсивне самонагрівання, подальше розкладання матеріалів та деформацію акумулятора. Припинення самонагрівання досліджували шляхом занурення акумулятора в ємність з надлишком води відносно стехіометричної кількості для максимальної маси металевого літію, яка може накопичуватися під час роботи акумулятора. Виділення газів реєстрували візуально, а у складі визначали водень. Вимірювали зміну кислотності отриманого водного розчину під час гасіння шляхом охолодження водою в надлишку. Встановлено залежності часу завершення реакції з водою для досліджуваного механічного пошкодження. Розраховано кількість води, необхідну для поглинання тепла, яке може виділятися під час реакцій; отримане значення корелює з експериментальними даними. Розглянуто можливі заходи щодо запобігання та зупинки горіння літій-іонних акумуляторів. Планується повторити поточну схему дослідження теплового розгону літій-іонного акумулятора, але не через механічне пошкодження, а за умов підвищеної температури навколишнього середовища та поганого теплообміну із зовнішнім простором.

  • Моделювання вибухонебезпечних властивостей амонійної селітри

    by Vitalii Nuianzin, Dmytro Tregubov, Artem Maiboroda, Larisa Trefilova, Volodymyr Mazurov

    Систематизовано уявлення стосовно механізмів виникнення вибухових властивостей амонійної селітри агропризначення. Показано, що сучасні уявлення лише частково описують випадковість таких подій без обґрунтування чітких механізмів розвитку. Систематизовано напрямки зміни властивостей селітри за різних добавок та умов зберігання, а також шляхи підвищення стійкості її будови під час зберігання. Порівняно механізми запобіганню виникненню вибухової здатності для типових агросумішей селітри з сульфатом амонію або карбонатом кальцію. Наведено схеми хімічних перетворень амонійної селітри під час розкладання за умов температурного впливу або інших шляхів ініціювання. Показано, що питомий тротиловий еквівалент вибуху амонійної селітри коливається у межах 0,45–1,35 залежно від набору супутніх факторів. Оцінено можливі наслідки вибуху для селітри агропризначення масою 3000 т на підставі усередненого тротилового еквіваленту вибуху. Оцінено можливі наслідки вибуху агросумішей селітри порушеного складу масою 10000 т за коефіцієнтом участі у вибуху. Проведено моделювання варіантів надмолекулярної будови амонійної селітри для стабільного стану та для моменту ініціювання вибухових перетворень з визначенням показника схильності до детонації КD на основі показника «легкості плавлення». Встановлено, що схема «лінійний кластер на основі нітробазису» дає високий показник схильності до детонації КD>1, що не відповідає дійсності; для тетрагональних ґраток отримано КD1, що визначає значні вибухові властивості. Можливість утворення різних надмолекулярних структур визначає можливість формування різних вибухових властивостей.

  • Using fire extinguishing experience in the metallurgical coke wet quenching technology

    by Dmytro Tregubov, Larisa Trefilova, Olena Danyk, Kateryna Rusenko, Volodymyr Mazurov

    The metallurgical coke wet quenching technology was improved. An efficiency comparison, cost-effectiveness and environmental friendliness of coke cooling processes after removal from the furnace using wet and dry methods was carried out. These processes similarity to water fire extinguishing and fire quenching with non-flammable gases was analyzed. Attention is focused on wet quenching advantages and disadvantages and this technology improving feasibility. It is argued that coke single-stage quenching has significant thermal stresses in the lump due to a significant temperature excess in the lump middle over the surface temperature, which at the same time reduces the wastewater impurities neutralization efficiency on the coke surface. The theoretical possibility of the wastewater utilization efficiency increasing using wet quenching, reducing water consumption, improving the coke quality as an important blast furnace process component, and reducing the toxic gas contamination area near the quenching tower is shown. It was established that this issues set can be solved by the water supply phasing selecting for quenching in a pulsed mode, which can ensure the coke lump cooling process uniformity. The water cooling capacity theoretical value of the under conditions of the coke standard single-stage wet quenching and under this ability full use conditions was calculated. It was shown that the using water efficiency as a cooling agent increases if it is completely evaporated and the steam is heated to the coke temperature. According to the assessment, the supply time and water consumption are reduced by 7.5 times when its cooling ability is fully utilized. It is proposed to carry out wet quenching in 3 stages: for 1 min – with concentrated wastewater, for 2 min – with diluted wastewater, for 3 min. – with technical water. The intervals system of water supply pulse mode for the coke cooling with a “supply-pause” scheme with a total quenching time of 219 s was developed, of which the total water supply time is 19 s.


  • Open Access

    PREDICTION OF AMMONIA DANGERS TAKING INTO ACCOUNT THE SUPRAMOLECULAR STRUCTUR

    by Dmytro Tregubov, Yuliana Hapon, Vitalii Nuianzin, Artem Maiboroda, Flora Trehubova, Юліана Гапон, Віталій Нуянзін

    The work aim is to analyze the ammonia hazards, ways to eliminate them, and to develop methods for hazards parameters predicting by the supramolecular structures modeling in comparison with hydrocarbons. The work task is to summarize information about ammonia hazards, analyze their origin, and extend assessing methods of the hydrocarbons supramolecular structure to the ammonia description. Thework analyzes the formation of physicochemical hazard indicators of ammonia and its aqueous solutions. A supramolecular structure influence theoretical assessment on the hazards genesis was carried out. Attention is focused on the developments lack for the such implementation an approach for ammonia. A standard techniques review for eliminating the dangers of ammonia and its aqueous solutions during storage or use in technological processes, as well as in the emergency leakage case, was carried out. Using the hydrocarbons example, the stepwiseness and decrease of maximum permissible concentrations (MPC) in homologous series, which is preserved for the ammonia–hydrazine pair, is shown. The close nature of the change in MPC, solubility in water, and the n-alcohols content in the azeotropic mixture with water was observed. The melting temperature, stoichiometric conditions of combustion, flammability limits, solubility in water were described in cluster structure parameters with a good correlation. To predict the ammonia properties, various schemes of the supramolecular structure worked: for the melting state, different combustion conditions, solubility in а water. The melting temperature is described by the clustering coefficient K = 14; the combustion stoichiometric condition –as an ammonia tetramer with 3 peroxide bridges; lower FL –as ammonia hydroperoxide with β = 1; the upper FL –as an ammonia dimer with 1 peroxide bridge with β = 0.5, an aqueous solution according by a scheme close to stoichiometric combustion conditions, as a tetramer and 14 associated water molecules.Key words:ammonia, hydrocarbons, hazards parameters, maximum permissible concentration, supramolecular structure, cluster, length.

  • Nonlinearities correlation of n-alkanes and n-alcohols physicochemical properties

    by Dmytro Tregubov, Oleksandr Kireev, Kyazim Kyazimov, Larisa Trefilova, Yevhen Slepuzhnikov, Sergei Vavreniuk

    The combustible liquid modulating parameter was established to predict the foam glass fire-extinguishing layer as the primary means for liquids ensuring reliable fire extinguishing in combination with other fire-extinguishing means. The formation peculiarities and buoyancy indicators of dry and wet foam glass in polar and non-polar liquids (alkanes and alcohols) were investigated. It is shown that the foam glass buoyancy increases with an increase in the liquid density. The foam glass buoyancy in polar and non-polar liquids was described depending on the liquid density by an approximate linear dependence separately for dry and wet foam glass. The deviation from the linear trend is explained by the foam glass different wettability, some alcohols water solubility, and liquid mixtures peculiarities. The buoyancy relation with flash point was established, which works separately for n-alkanes, n-alcohols and glycols, which was described mathematically. A formula was developed to describe the relationship between flash temperatures and the liquids density. Correlations with a fire-extinguishing layer of dry foam glass for molar mass, molecule or cluster length, stoichiometric combustion reaction coefficient, burning rate on a free surface, density, flash point, boiling point, autoignition temperature were studied. The forecasting possibility the dry foam glass fire-extinguishing layer based on the description of flammable liquids clusters has been established. Mathematical dependences were obtained for the dry foam glass fire-extinguishing layer depending on the expected clusters length in the liquid and a similar dependence for flash points. The conditions for effective extinguishing of alcohols and alkanes with dry foam glass have been determined. Different modes of extinguishing hydrocarbons with flash temperatures tfp28 оС are recommended, based on the primary layer of 6 cm of wet foam glass with a fraction of 1.0–1.5 cm, with the possibility of finalizing the extinguishing, if necessary, with an inorganic gel by spraying components with an application rate of 0.2 g/cm2.


  • Nonlinearities correlation of n-alkanes and n-alcohols physicochemical properties

    by Dmytro Tregubov, Larisa Trefilova, Natalya Minska, Yuliana Hapon, Dmitry Sokolov

    Correspondences between the changes nonlinearity in substance physico-chemical parameters and the influence mechanisms on them by the substance supramolecular structure in the calculated dependencies form for n-alkanes and n-alcohols was established. Similarity, change features and correlation between such parameters as melting point, boiling point, flash point, self-ignition, density, solubility in water, viscosity, vaporization heat, surface tension were investigated. The paper obtained 14 calculated dependencies that calculate these parameters on the established similarity basis between them and the lengths of the molecule or cluster with sufficient correlation coefficients. For viscosity, vaporization heat and surface tension, change general dependences are established, but without taking into account oscillatory deviations. Calculated dependences between substance characteristic temperatures were obtained: melting temperatures of alkanes and alcohols, boiling and flash temperatures in homologous series, autoignition and melting temperatures (flash, boiling). This correlation is explained by the fact that supramolecular structures are formed according to a similar principle in matter different states and during the combustion initiation. Such structures modeling for the solid, liquid state, and solubility in water was carried out, taking into account different coordination numbers, globulation, and changes in the clustering place according to the molecule length. On the such modeling basis and the "melting ease" indicator, dependencies have been developed for calculation with the dependencies nonlinearities reflection of alkanes and alcohols density and melting temperature. For the boiling and flash point, vaporization heat of alcohols, the deviation from linearity is taken into account by the cluster length reduction parameter. It is shown that the considered dependencies modulation by the cluster length allows to describe their anomalies and increases the calculation convergence.


  • STUDY OF THE SUPRAMOLECULAR STRUCTURE INFLUENCE ON HYDROCARBONS FIRE HAZARD PARAMETERS

    by National University of Civil Protection of Ukraine, Dmytro Tregubov, Flora Tregubova

    A theoretical study of the supramolecular structure influence on the hydrocarbons fire hazard parameters formation was conducted. The work aim is to develop a mechanism for modeling possible supramolecular structures in a flame and to demonstrate the such an approach efficiency for calculating fire hazard parameters. The characteristic temperatures pulsation in homologous series due to differences in molecules clustering mechanisms were chosen assupramolecular state features indicators. It is shown that flash and autoignition temperatures have a change pulsation in the n-alkanes homologous series, which is similar to changes in melting points and solubility in water. An assumption is made about the clustering primary stage presence by the peroxide mechanism during the flame combustion occurrence with the formation of an oxygen bridge between molecules, which is similar to solubility in water. It is shown that fire hazard parameters can depend both on the smallest cluster length and on the associated oxygen molecules number during the combustion initiation.The n-alkanes aggregation proportions into clusters with the oxygen molecules participation have been determined, which allow us to describe the critical conditions for the combustion initiation with the sufficient convergence: lower and upper flammability limits, lower and upper detonation limits, the stoichiometric concentration, the cold flame upper limit. A formula was developed for the n-alkanes autoignition temperatures predictingbased on the "ease of melting" indicator, which works with R=0.98. It is shown that supramolecular peroxide structures formed during the combustion initiation have easier conditions for the condensation.It is calculated that the expected corresponding characteristic temperatures of peroxide clusters phase transitions can be realized in a flame.The condensation processes participation during combustion determines the flame front minimum thickness for the single peroxide-polymer structure formation.Key words:hydrocarbons, characteristic temperatures, cluster, structure, length, peroxide proportion, fire hazard.

  • Correlation of properties in hydrocarbons homologous series

    by Dmytro Tregubov, Larisa Trefilova, Evgen Slepuzhnikov, Dmytro Sokolov, Flora Trehubova

    Correlations between combustible substances properties in the homologous series of n-alkanes and n-alcohols with a length of nС=1–20 were studied in order to determine ways to increase the methods convergence for assessing fire hazard parameters. The cluster length was added to the substance modulating parameters set. It should be noted that substances properties are often predicted using a molecule coarse-grained model, which has discreteness, does not describe short molecules, and requires an individual approach. It is shown that there are substance "arithmetic" parameters that directly depend on the certain atoms number. Among them, "length" better reflects isomeric, conformal, cluster differences, which are associated with parameters anomalies of hydrocarbons. A vaporization heat linear description from nС separately for n-alkanes and n-alcohols gives R=0,999. Exponential approximation of the n-alkanes boiling point tbp and flash point tfp by nС change fractions has R=0,999. It is shown that there is a correlation between tfp and tbp, but with a systematic difference, which indicates that the cluster composition is not completely similar at these temperatures; between tfp and tmp there is a smaller correlation, but its presence indicates clusters partial similarity. A universal formula for predicting hydrocarbons vaporization heats of 10 homologous series has been created, which has R=0,996. The description change hydrocarbons pulsations of in tmp was carried out on the cluster schemes alternation basis in homologous series, as well as taking into account their length and molar mass, which gives R=0,9997. According to similar principles, a formula for the hydrocarbons solubility in the water has been developed, which has the satisfactory accuracy. The study showed that the cluster length is a determining factor by which substance properties are modulated.


  • ПЕРОКСИДНО-КЛАСТЕРНИЙ МЕХАНІЗМ ІНІЦІЮВАННЯ САМОСПАЛАХУВАННЯ

    by Дмитро Трегубов

    Розглянуто вплив пероксидної природи ініціювання самоспалахування на стадійність цього процесу та необхідні зміни у методиці розрахункового прогнозування температури самоспалахування. Дослідження побудовано на припущенні, що першим елементарним актом, який призводить до самоспалахування, є утворення надмолекулярної структури як кластера пероксидного типу. Метою роботи є проведення моделювання найменшої надмолекулярної пероксидної будови вуглеводнів, яка виникає на першому етапі самоспалахування, для уточнення пероксидного механізму розвитку цього виду виникнення горіння та підвищення збіжності розрахункового прогнозування температури самоспалахування. Як базовий гомологічний ряд для моделювання таких структур обрано н- алкани. Встановлено нелінійність температур самоспалахування у зазначеному гомологічному ряду з елементами коливальності, що є ознакою існування надмолекулярних структур із неоднаковим принципом організації для різних сполук, аналогічно властивостям речовин у конденсованому стані. Для першого моменту ініціювання процесів самоспалахування визначено механізм формування взаємозв’язку між нелінійністю зміни температури самоспалахування та будовою найменших можливих кластерів пероксидного типу: формування алкілпероксидного кластера димерної будови, а для метану – додатково гекса-, для етану – тримерної будови. Розраховано усереднені еквівалентні довжини цих структур для суміші лінійних та циклічних алкілпероксидів, що модулює нелінійність зміни температури самоспалахування. Розроблено аналітичну залежність апроксимаційного характеру для опису температури самоспалахування, яка працює з коефіцієнтом кореляції R=0,977 та середнім відхиленням 5,5 оС. Новизною роботи є передбачений кластерний механізм ініціювання самоспалахування та відповідні варіанти можливих надмолекулярних структур пероксидного типу, що дало змогу розробити нову аналітичну залежність для прогнозування температури самоспалахування на підставі значень еквівалентних довжин цих структур та стехіометричного коефіцієнта реакції горіння речовини.

  • Забезпечення балансу властивостей плавучих систем для гальмування випаровування небезпечних рідин

    by Dmytro Tregubov, Oleksandr Kireev, Larisa Trefilova, Maryna Chyrkina, Ilgar Firdosi Dadashov

    Встановлено баланс внесків властивостей засобів, призначених для гальмування ви-паровування рідин та забезпечення безпечних концентрацій пари, у залежності від значень характерних температур та водорозчинності. Доведено, що обмеження розмірів парогазо-вої хмари досягається засобами ізоляції або охолодження поверхні рідини. Показано, що подовжену дію таких засобів можуть забезпечити лише закритопористі плавучі тверді ма-теріали (наприклад, піноскло) і піни, що тверднуть. Акцентовано увагу на таких недоліках вказаних засобів, як мала ізолююча здатність піноскла та незначна охолоджуюча здатність, а для твердіючої піни – горючість. Дослідним шляхом встановлено наявність менших кое-фіцієнтів гальмування випаровування гелем для рідин з більшою водорозчинністю. Дослід-ним шляхом встановлено наявність більшої охолоджуючої здатності у вологого піноскла, ніж у сухого, у 5–6 разів з близькою залежністю для охолодження полярних та неполярних рідин. Показано, що охолоджуючий ефект від подавання піноскла менший для рідин з бі-льшою теплотою випаровування, причому ця різниця приблизно однакова для випадків по-давання як сухого, так і вологого піноскла. Встановлено, що для легкокиплячих неполярних рідин ізоляція випаровування більш ефективно досягається за використання ізолюючої сис-теми на основі сухого піноскла з шаром гелю, а для важкокиплячих рідин – за умови подачі охолоджуючої системи у вигляді вологого піноскла. Визначено, що додатковий внесок у запобігання та припинення горіння за використання водовмісних засобів на основі піно-скла надає флегматизація повітряного простору над поверхнею рідини водяною парою. Доведе-но, що зменшення масової швидкості вигоряння та ефект пожежогасіння за нанесення на поверхню горючої рідини шару піноскла відбувається схожим чином для рідин з близькими моляр-ними масами, а не температурами спалаху.