Sudharshanaraj Thiruppathiraj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sudharshanaraj Thiruppathiraj has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Laxminarayan L. Raja
Department of Aerospace Engineering and Engineering Mechanics, The University of Texas at Austin , Austin, Texas 78712
2 shared publications - Dmitry Levko
Esgee Technologies Inc. , Austin, Texas 78746
1 shared publication Jiho Uh
Memory Technology Innovation Team, Samsung Electronics 2 , 1, Samsungjeonja-ro, Hwaseong-si, Gyeonggi-do 18448, Republic of Korea
1 shared publicationSeung-Min Ryu
Department of Aerospace Engineering and Engineering Mechanics, The University of Texas at Austin 1 , Austin, Texas 78712
1 shared publication
Latest Publications
- Open Access
- 1 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (17)
Computational analysis of the anode-directed streamers propagation in atmospheric pressure C4F7N/N2 mixtures
In recent years, interest in synthetic C4F7N as a gas insulator has been growing due to its unique insulation properties and low global warming potential. In spite of this, very few studies are devoted to the analysis of the electric breakdown of C4F7N and its mixtures with other dilutants such as CO2 and N2. In the present paper, we use a two-dimensional fluid model to analyze the electrical breakdown of the atmospheric pressure C4F7N/N2 mixture. We establish the influence of the C4F7N fraction in the mixture and the cathode voltage rise rate on the breakdown voltage. We find that the ratio between the electron attachment frequency and the voltage rise rate defines the streamer parameters. Namely, if the time scale of electron attachment to C4F7N is much faster than the voltage rise rate, the plasma electronegativity of the streamer body and of its head is extremely high, and it is difficult to define exactly the streamer head location. In the opposite case of the fast rise rates, the conventional streamers with sharp heads were obtained.
- 1 May 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (17)
Open AccessComputational analysis of the anode-directed streamers propagation in atmospheric pressure C4F7N/N2 mixtures
In recent years, interest in synthetic C4F7N as a gas insulator has been growing due to its unique insulation properties and low global warming potential. In spite of this, very few studies are devoted to the analysis of the electric breakdown of C4F7N and its mixtures with other dilutants such as CO2 and N2. In the present paper, we use a two-dimensional fluid model to analyze the electrical breakdown of the atmospheric pressure C4F7N/N2 mixture. We establish the influence of the C4F7N fraction in the mixture and the cathode voltage rise rate on the breakdown voltage. We find that the ratio between the electron attachment frequency and the voltage rise rate defines the streamer parameters. Namely, if the time scale of electron attachment to C4F7N is much faster than the voltage rise rate, the plasma electronegativity of the streamer body and of its head is extremely high, and it is difficult to define exactly the streamer head location. In the opposite case of the fast rise rates, the conventional streamers with sharp heads were obtained.
- 5 August 2021
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 39 (5) , 052404
Direct-simulation Monte Carlo modeling of reactor-scale gas-dynamic phenomena in a multiwafer atomic-layer deposition batch reactor
Atomic layer deposition (ALD) using multiwafer batch reactors has now emerged as the manufacturing process of choice for modern microelectronics at a massive scale. Stringent process requirements of thin film deposition uniformity within wafer (WiW) and wafer–wafer (WTW) in the batch, film conformity along submicrometer wafer features, thin film quality, and the utilization of expensive precursors in the reactor dictate ALD reactor design and process parameter optimization. This paper discusses a particle-based direct-simulation Monte Carlo (DSMC) of the full reactor scale simulation that overcomes the low Knudsen number limitation of typical continuum computational fluid dynamics approaches used for modeling low-pressure ALD reactors. A representative industrial multiwafer batch reactor used for the deposition of Si-based thin films with N2 and Si2Cl6 (hexachlorodisilane) as process feed gases with pressures in the range 43–130 Pa and a uniform reactor temperature of 600 °C is simulated. The model provides detailed insights into the flow physics associated with the transport of the precursor species from the inlets, through wafer feed nozzles, into the interwafer regions, and finally through the outlet. The reactor operating conditions are shown to be in the slip/transitional flow regime for much of the reactor volume and especially the feed gas nozzle and interwafer regions (where the Knudsen number approaches ∼0.2), justifying the need for a high-Knudsen number DSMC approach as in this work. For the simulated conditions, the nonuniformity of precursor species immediately above the wafer surface is predicted to be within <1% for a given wafer and <2% across the entire multiwafer stack. Results indicate that higher pressure degrades WiW and WTW uniformity. A reactor flow efficiency is defined and found to be ∼99%, irrespective of the chamber pressure.
- 5 August 2021
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 39 (5) , 052404
Direct-simulation Monte Carlo modeling of reactor-scale gas-dynamic phenomena in a multiwafer atomic-layer deposition batch reactor
Atomic layer deposition (ALD) using multiwafer batch reactors has now emerged as the manufacturing process of choice for modern microelectronics at a massive scale. Stringent process requirements of thin film deposition uniformity within wafer (WiW) and wafer–wafer (WTW) in the batch, film conformity along submicrometer wafer features, thin film quality, and the utilization of expensive precursors in the reactor dictate ALD reactor design and process parameter optimization. This paper discusses a particle-based direct-simulation Monte Carlo (DSMC) of the full reactor scale simulation that overcomes the low Knudsen number limitation of typical continuum computational fluid dynamics approaches used for modeling low-pressure ALD reactors. A representative industrial multiwafer batch reactor used for the deposition of Si-based thin films with N2 and Si2Cl6 (hexachlorodisilane) as process feed gases with pressures in the range 43–130 Pa and a uniform reactor temperature of 600 °C is simulated. The model provides detailed insights into the flow physics associated with the transport of the precursor species from the inlets, through wafer feed nozzles, into the interwafer regions, and finally through the outlet. The reactor operating conditions are shown to be in the slip/transitional flow regime for much of the reactor volume and especially the feed gas nozzle and interwafer regions (where the Knudsen number approaches ∼0.2), justifying the need for a high-Knudsen number DSMC approach as in this work. For the simulated conditions, the nonuniformity of precursor species immediately above the wafer surface is predicted to be within <1% for a given wafer and <2% across the entire multiwafer stack. Results indicate that higher pressure degrades WiW and WTW uniformity. A reactor flow efficiency is defined and found to be ∼99%, irrespective of the chamber pressure.