Andrew Cannon
Andrew Cannon has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Emily M. Ryan
Department of Mechanical Engineering, Boston University, Boston, Massachusetts 02215, United States
2 shared publications - Alexei P. Sokolov
University of Tennessee
1 shared publication - Dandan Yang
Experimental Teaching Center of Materials Science, School of Materials Science and Engineering, Nankai University, Tianjin 300350, China
1 shared publication Emily Ryan
Boston University
1 shared publication- Feiyuan Sun
Institute of New Energy Material Chemistry, School of Materials Science and Engineering, Nankai University, Tianjin 300350, China
1 shared publication - Huabin Yang
Institute of New Energy Material Chemistry School of Materials Science and Engineering Nankai University Tianjin China
1 shared publication
Latest Publications
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (62) , 2926
Li-Ion Cell in Operando Monitoring and Prognostication Using CMUT Devices
Capacitive micromachined ultrasonic transducer (CMUT) devices are ideal solutions for in operando battery monitoring applications especially for consumer electronics. Their minute size (2mm x 1mm x 0.5mm) allows direct placement on the battery without affecting the form factor of the device, the volume production techniques used for their manufacture allow for a very low-cost device, and they can be easily integrated with front-end integrated circuits either in a single device or in a discrete multichip form. Together with industry partners we have developed CMUT devices that we use to continuously monitor the behavior of a battery while it is cycling. For this work we used CMUTs (close-up shown in Fig. 1(a)) developed to operate with a low bias voltage (less than 30 V) which reduces the complexity of the driving hardware. The impulse response and its frequency content are shown in Fig. 1(b). In collapse mode, the peak frequency is 4.0 MHz and the one-way –3 dB BW is 76%, which allows flexibility in setting the drive conditions to interrogate the battery. Our testing also shows that the CMUTs show good device-to-device uniformity and they have a very stable performance in variable temperature environments (e.g. 0℃ - 60℃ ). The cell is interrogated in pulse-echo mode. The CMUT is excited by a wide-band unipolar pulse and the returned analog signal is filtered and amplified. The signal is then digitized and processed to extract features that allow us to quantify the state of the battery. Figure 1(c) depicts such signal features change under baseline cell cycling conditions (three cycles at a charge rate of C/4). These changes are the result of mechanical material property changes in the cell e.g., electrode stiffness and density [1] which directly affect the acoustic wave propagation inside the cell. Figure 1(d) depicts signal feature change due cell overcharge (red line). Ultrasound is especially sensitive to gas generation which occurs as the cell voltage extends beyond normal operating range [2]. Signal features provide early warning notice that cell is outside of normal operating conditions. Figure 1. a) Close-up image of CMUT device. b) CMUT impulse response and corresponding frequency content. c) Signal features (RMS and Time of Flight (ToF)) and thickness change during C/4 charge and discharge. d) Signal features during cell constant current overcharge. Cell overcharged after 4.4V (red line). Chang, W. et al. Measuring effective stiffness of Li-ion batteries via acoustic signal processing. Mater. Chem. A 8, 16624–16635 (2020). Appleberry, M. C. et al. Avoiding thermal runaway in lithium-ion batteries using ultrasound detection of early failure mechanisms. Journal of Power Sources 535, 231423 (2022). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (62) , 2926
Li-Ion Cell in Operando Monitoring and Prognostication Using CMUT Devices
Capacitive micromachined ultrasonic transducer (CMUT) devices are ideal solutions for in operando battery monitoring applications especially for consumer electronics. Their minute size (2mm x 1mm x 0.5mm) allows direct placement on the battery without affecting the form factor of the device, the volume production techniques used for their manufacture allow for a very low-cost device, and they can be easily integrated with front-end integrated circuits either in a single device or in a discrete multichip form. Together with industry partners we have developed CMUT devices that we use to continuously monitor the behavior of a battery while it is cycling. For this work we used CMUTs (close-up shown in Fig. 1(a)) developed to operate with a low bias voltage (less than 30 V) which reduces the complexity of the driving hardware. The impulse response and its frequency content are shown in Fig. 1(b). In collapse mode, the peak frequency is 4.0 MHz and the one-way –3 dB BW is 76%, which allows flexibility in setting the drive conditions to interrogate the battery. Our testing also shows that the CMUTs show good device-to-device uniformity and they have a very stable performance in variable temperature environments (e.g. 0℃ - 60℃ ). The cell is interrogated in pulse-echo mode. The CMUT is excited by a wide-band unipolar pulse and the returned analog signal is filtered and amplified. The signal is then digitized and processed to extract features that allow us to quantify the state of the battery. Figure 1(c) depicts such signal features change under baseline cell cycling conditions (three cycles at a charge rate of C/4). These changes are the result of mechanical material property changes in the cell e.g., electrode stiffness and density [1] which directly affect the acoustic wave propagation inside the cell. Figure 1(d) depicts signal feature change due cell overcharge (red line). Ultrasound is especially sensitive to gas generation which occurs as the cell voltage extends beyond normal operating range [2]. Signal features provide early warning notice that cell is outside of normal operating conditions. Figure 1. a) Close-up image of CMUT device. b) CMUT impulse response and corresponding frequency content. c) Signal features (RMS and Time of Flight (ToF)) and thickness change during C/4 charge and discharge. d) Signal features during cell constant current overcharge. Cell overcharged after 4.4V (red line). Chang, W. et al. Measuring effective stiffness of Li-ion batteries via acoustic signal processing. Mater. Chem. A 8, 16624–16635 (2020). Appleberry, M. C. et al. Avoiding thermal runaway in lithium-ion batteries using ultrasound detection of early failure mechanisms. Journal of Power Sources 535, 231423 (2022). Figure 1
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (25) , 1649
(Invited) The Importance of Modeling Interfacial Phenomena in Electrochemical Systems
Chemical-physical processes at material interfaces drive performance and degradation in various energy and environmental systems, such as high energy density batteries, fuel cells, and electrolyzers. Transport (mass, charge, heat) to and through interfaces combined with reactions on the surface dictate the performance and also the degradation of these systems. To understand the fundamental material behavior of electrochemical systems, and to improve their performance and lifetime meso-scale interfacial modeling is needed that can resolve both the surface phenomena and the transport within the interfacial region. In this talk, I will discuss our research into computational modeling of interfacial and surface phenomena that drive performance in high energy density lithium batteries. Over multiple charge/discharge cycles non-uniform lithium plating and secondary reactions at the interface drive performance degradation and pose safety risks. The interplay between local transport, surface conditions, and operating conditions dictate these interfacial changes. In our work we use multi-phase, meso-scale modeling of the interfacial region to understand the driving forces for these changes and the coupling between physical phenomena to better understand the critical physics at the interface and to design more stable, long lasting interfaces.
- 28 August 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-01 (25) , 1649
(Invited) The Importance of Modeling Interfacial Phenomena in Electrochemical Systems
Chemical-physical processes at material interfaces drive performance and degradation in various energy and environmental systems, such as high energy density batteries, fuel cells, and electrolyzers. Transport (mass, charge, heat) to and through interfaces combined with reactions on the surface dictate the performance and also the degradation of these systems. To understand the fundamental material behavior of electrochemical systems, and to improve their performance and lifetime meso-scale interfacial modeling is needed that can resolve both the surface phenomena and the transport within the interfacial region. In this talk, I will discuss our research into computational modeling of interfacial and surface phenomena that drive performance in high energy density lithium batteries. Over multiple charge/discharge cycles non-uniform lithium plating and secondary reactions at the interface drive performance degradation and pose safety risks. The interplay between local transport, surface conditions, and operating conditions dictate these interfacial changes. In our work we use multi-phase, meso-scale modeling of the interfacial region to understand the driving forces for these changes and the coupling between physical phenomena to better understand the critical physics at the interface and to design more stable, long lasting interfaces.
- Open Access
- 1 August 2021
- Published by Elsevier in Cell Reports Physical Science
- Vol. 2 (8) , 100534
Glass-fiber-reinforced polymeric film as an efficient protecting layer for stable Li metal electrodes
- 1 August 2021
- Published by Elsevier in Cell Reports Physical Science
- Vol. 2 (8) , 100534
Open AccessGlass-fiber-reinforced polymeric film as an efficient protecting layer for stable Li metal electrodes
- 28 July 2021
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 4 (8) , 7848-7861
Characterizing the Microstructure of Separators in Lithium Batteries and Their Effects on Dendritic Growth
- 28 July 2021
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 4 (8) , 7848-7861
Characterizing the Microstructure of Separators in Lithium Batteries and Their Effects on Dendritic Growth