Ming Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ming Zhang has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Jun Han
College of Mining, Liaoning Technical University, Fuxin, China
2 shared publications Bingjie Huo
College of Mining
1 shared publicationChen Cao
Affiliations College of Mining, Liaoning Technical University, Fuxin, China, EIS, CME, University of Wollongong, Wollongong, NSW, Australia
1 shared publication- Chen Cao
College of Mining, Liaoning Technical University, Fuxin 123000, China
1 shared publication - Chen Cao
College of Mining
1 shared publication Shuangwen Ma
Affiliation College of Mining, Liaoning Technical University, Fuxin, China
1 shared publication
Latest Publications
- Open Access
- 30 August 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (17) , 8041
An Equivalent Radial Stiffness Method of Laboratory SEPT on Anchorage Performance Prediction of Rockbolts under Different Field Geoconditions
The short encapsulation pull-out test (SEPT) is extensively used in rockbolting research or engineering. The field SEPT is time-consuming and labor-intensive, and its result is only applicable to the tested in situ. The laboratory SEPT is usually employed in theoretical rockbolting research due to its easily controlled variables. However, the design of laboratory SEPT is quite different, as there is no standard testing method, resulting in the applicability and limitations of each study not being clear. Accordingly, the aim of this paper is to bridge the gap between laboratory SEPT research and field application. On the basis of thick-walled cylinder theory, a mechanical model of a rock bolt subjected to axial load was established under consideration of the deformational behavior of confining materials around the bolt. Plane stress analysis was introduced to derive the analytical relationship between the axial force of the bolt and the deformation of the confining materials. A new approach of laboratory SEPT sample design was established, namely, equivalent radial stiffness theory, to simulate anchorage performance in a specific in-situ geocondition. Consequently, the field SETP could be replaced by laboratory testing using properly designed bolting samples with a certain level of accuracy. In addition, the application scope of previous laboratory SEPT research could be accurately defined. Laboratory SEPT was carried out to study the anchoring performance of right spiral rebar bolts under different confining materials. Poly Vinyl Chloride (PVC) tubes with a thickness of 31 mm, #60 aluminum (Al) tubes with a thickness of 5.8 mm, and #20 steel tubes with a thickness of 5.5, 7.0 mm were used in sample preparation to simulate soft, medium, and hard surrounding rocks in the field. The anchorage performance of the bolt under different geoconditions was systematically proposed, which provides a technical approach for similar research using different anchoring materials. A negative exponential expression formulating the axial load capacity of the right spiral bolts for the full spectrum of the surrounding rocks’ strength was derived on the basis of theoretical analysis and data regression. It can be used for preliminary reinforcement design, as well as the accurate key parameter setting in the numerical calculation of roadway deformation using right spiral bolts. The theoretical prediction is highly consistent with the testing results in the literature, which confirms the validity and reliability of this research. This study contributes to the establishment of a laboratory SEPT standard in rock mechanics.
- 30 August 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (17) , 8041
Open AccessAn Equivalent Radial Stiffness Method of Laboratory SEPT on Anchorage Performance Prediction of Rockbolts under Different Field Geoconditions
The short encapsulation pull-out test (SEPT) is extensively used in rockbolting research or engineering. The field SEPT is time-consuming and labor-intensive, and its result is only applicable to the tested in situ. The laboratory SEPT is usually employed in theoretical rockbolting research due to its easily controlled variables. However, the design of laboratory SEPT is quite different, as there is no standard testing method, resulting in the applicability and limitations of each study not being clear. Accordingly, the aim of this paper is to bridge the gap between laboratory SEPT research and field application. On the basis of thick-walled cylinder theory, a mechanical model of a rock bolt subjected to axial load was established under consideration of the deformational behavior of confining materials around the bolt. Plane stress analysis was introduced to derive the analytical relationship between the axial force of the bolt and the deformation of the confining materials. A new approach of laboratory SEPT sample design was established, namely, equivalent radial stiffness theory, to simulate anchorage performance in a specific in-situ geocondition. Consequently, the field SETP could be replaced by laboratory testing using properly designed bolting samples with a certain level of accuracy. In addition, the application scope of previous laboratory SEPT research could be accurately defined. Laboratory SEPT was carried out to study the anchoring performance of right spiral rebar bolts under different confining materials. Poly Vinyl Chloride (PVC) tubes with a thickness of 31 mm, #60 aluminum (Al) tubes with a thickness of 5.8 mm, and #20 steel tubes with a thickness of 5.5, 7.0 mm were used in sample preparation to simulate soft, medium, and hard surrounding rocks in the field. The anchorage performance of the bolt under different geoconditions was systematically proposed, which provides a technical approach for similar research using different anchoring materials. A negative exponential expression formulating the axial load capacity of the right spiral bolts for the full spectrum of the surrounding rocks’ strength was derived on the basis of theoretical analysis and data regression. It can be used for preliminary reinforcement design, as well as the accurate key parameter setting in the numerical calculation of roadway deformation using right spiral bolts. The theoretical prediction is highly consistent with the testing results in the literature, which confirms the validity and reliability of this research. This study contributes to the establishment of a laboratory SEPT standard in rock mechanics.
- Open Access
- 28 July 2021
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 16 (7) , e0255046
Experimental study on anchorage performance of rockbolts by adding steel aggregates into resin anchoring agents
Pull-out testing was carried out to evaluate the effects of shape, size and concentration of steel aggregates on anchorage performance. Steel grit with particle sizes of 1.5, 2.0, and 2.8 mm and steel shot diameters of 1.4, 2.0, and 2.5 mm were used as steel aggregates and were added into the resin anchoring agent. For each kind of steel aggregate, either 30, 40 or 50 aggregates were used to evaluate the effects of different steel aggregate densities. Anchorage specimens were prepared using ϕ20mm rebar bolts and steel sleeves. Compressive and shear strengths of resin containing steel aggregates, the pullout curve, and the circumferential strain of the sleeves were measured, and the energy consumption was calculated. Results show that compressive and shear strengths of resin containing steel grit and steel shot are increased by 8.4%-17.0% compared to pure resin. For the aggregate numbers of 30, 40 and 50, the anchoring force is increased by 7.9%, 7.5% and 6.5%; energy consumption is increased by 19.2%, 15.0% and 18.6%; and the circumferential strain of the specimen is increased by 28.4%, 25.1% and 39.5%, respectively. The effect of aggregate size on anchoring performance is significant; that is, the aggregate sizes of 1.4~1.5, 2.0 and 2.5~2.8 mm increase the anchoring force, energy consumption and sleeve circumferential strain by 8.5%, 4.6% and 8.7%, 16.0%, 8.4% and 28.4%, and 17.9%, 23.3% and 51.9%, respectively. The relationships of the anchoring force, energy consumption, and circumferential strain with steel aggregate quantity and size are formulated. Results show that the addition of steel aggregates increases the compressive and shear strengths of the resin, and steel aggregate quantity and size have significant impact on anchoring performance. This paper provides the basis for optimization of resin anchoring agents used in the mining industry. The impact of anchoring agent shear strength and residual shear strength on the anchoring effect were also discussed based on the failure analysis of the anchoring section.
- 28 July 2021
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 16 (7) , e0255046
Open AccessExperimental study on anchorage performance of rockbolts by adding steel aggregates into resin anchoring agents
Pull-out testing was carried out to evaluate the effects of shape, size and concentration of steel aggregates on anchorage performance. Steel grit with particle sizes of 1.5, 2.0, and 2.8 mm and steel shot diameters of 1.4, 2.0, and 2.5 mm were used as steel aggregates and were added into the resin anchoring agent. For each kind of steel aggregate, either 30, 40 or 50 aggregates were used to evaluate the effects of different steel aggregate densities. Anchorage specimens were prepared using ϕ20mm rebar bolts and steel sleeves. Compressive and shear strengths of resin containing steel aggregates, the pullout curve, and the circumferential strain of the sleeves were measured, and the energy consumption was calculated. Results show that compressive and shear strengths of resin containing steel grit and steel shot are increased by 8.4%-17.0% compared to pure resin. For the aggregate numbers of 30, 40 and 50, the anchoring force is increased by 7.9%, 7.5% and 6.5%; energy consumption is increased by 19.2%, 15.0% and 18.6%; and the circumferential strain of the specimen is increased by 28.4%, 25.1% and 39.5%, respectively. The effect of aggregate size on anchoring performance is significant; that is, the aggregate sizes of 1.4~1.5, 2.0 and 2.5~2.8 mm increase the anchoring force, energy consumption and sleeve circumferential strain by 8.5%, 4.6% and 8.7%, 16.0%, 8.4% and 28.4%, and 17.9%, 23.3% and 51.9%, respectively. The relationships of the anchoring force, energy consumption, and circumferential strain with steel aggregate quantity and size are formulated. Results show that the addition of steel aggregates increases the compressive and shear strengths of the resin, and steel aggregate quantity and size have significant impact on anchoring performance. This paper provides the basis for optimization of resin anchoring agents used in the mining industry. The impact of anchoring agent shear strength and residual shear strength on the anchoring effect were also discussed based on the failure analysis of the anchoring section.
- Open Access
- 1 January 2021
- Published by Wiley in Shock and Vibration
- Vol. 2021 (1)
Ground Stress Distribution and Dynamic Pressure Development of Shallow Buried Coal Seam Underlying Adjacent Room Gobs
The condition of the coal pillars remained in the room‐and‐pillar gobs is complicated. The stresses loaded on the pillar floor may be transmitted and overlapped. It changes the stress environment of the lower coal seam roof, leading abnormal periodic weighting. In the procedure of coal seam 3−1 mining in the Huoluowan Coal Mine, the ground stress is high while the working face passing through the room pillars of overlying coal seam 2−2, leading to hydraulic shield being broken. In this paper, theoretical analysis, numerical calculation, and similar material simulation were used to analyse the stress environment of lower seam and the effect of coal pillars remained in close‐distanced upper seam. The stress transfer model was established for the room pillars of coal seam 2−2, and the stress distribution of underlying strata was obtained based on theoretical analysis. The joint action of dynamic pressure of high stress‐coal pillar with movement of overlying rock strata in the working face 3−1 under the coal pillar was revealed. The results showed that the horizontal stress and vertical stress under the large coal pillar of the room gob in coal seam 2−2 were high, being from 9.7 to 15.3 MPa. The influencing depth of vertical stress ranged from 42 m to 58 m. The influencing depth of horizontal stress ranged from 10 to 23 m. The influencing range of the shear stress was from 25 to 50 m. When the working face 3−1 was mined below the coal pillar of 20 m or 50 m, abutment pressure was relatively high. The stress concentration coefficient reached 4.44–5.00. The dynamic pressure of the working face was induced by the stress overlying of the upper and lower coal seams, instability of the inverted trapezoid rock pillar above the coal pillar, and collapsing movement of the roof. The studying results were beneficial for guiding the safety mining of the coal seam 3−1 in the Huoluowan Coal Mine.
- 1 January 2021
- Published by Wiley in Shock and Vibration
- Vol. 2021 (1)
Open AccessGround Stress Distribution and Dynamic Pressure Development of Shallow Buried Coal Seam Underlying Adjacent Room Gobs
The condition of the coal pillars remained in the room‐and‐pillar gobs is complicated. The stresses loaded on the pillar floor may be transmitted and overlapped. It changes the stress environment of the lower coal seam roof, leading abnormal periodic weighting. In the procedure of coal seam 3−1 mining in the Huoluowan Coal Mine, the ground stress is high while the working face passing through the room pillars of overlying coal seam 2−2, leading to hydraulic shield being broken. In this paper, theoretical analysis, numerical calculation, and similar material simulation were used to analyse the stress environment of lower seam and the effect of coal pillars remained in close‐distanced upper seam. The stress transfer model was established for the room pillars of coal seam 2−2, and the stress distribution of underlying strata was obtained based on theoretical analysis. The joint action of dynamic pressure of high stress‐coal pillar with movement of overlying rock strata in the working face 3−1 under the coal pillar was revealed. The results showed that the horizontal stress and vertical stress under the large coal pillar of the room gob in coal seam 2−2 were high, being from 9.7 to 15.3 MPa. The influencing depth of vertical stress ranged from 42 m to 58 m. The influencing depth of horizontal stress ranged from 10 to 23 m. The influencing range of the shear stress was from 25 to 50 m. When the working face 3−1 was mined below the coal pillar of 20 m or 50 m, abutment pressure was relatively high. The stress concentration coefficient reached 4.44–5.00. The dynamic pressure of the working face was induced by the stress overlying of the upper and lower coal seams, instability of the inverted trapezoid rock pillar above the coal pillar, and collapsing movement of the roof. The studying results were beneficial for guiding the safety mining of the coal seam 3−1 in the Huoluowan Coal Mine.